• Proceedings of the Korean Institute of Building Construction Conference
• /
• 2005.05a
• /
• pp.45-48
• /
• 2005

This study is basic experiment for estimating influence of strength by curing temperature of concrete's heat of hydration and estimate relationship of compressive strength development by initial curing temperature factor, and then asume temperature factor which influence compressive strength development and for showing basic document of qualify control. According to the result of cement mortar by the curing temperature factor high-curing temperature shows high strength on 3 day compare with low curing-temperature, shows higher strength than the piece of high curing temperature.

• Structural Engineering and Mechanics
• /
• v.46 no.1
• /
• pp.39-51
• /
• 2013

An extremum method is presented to predict the wrinkling characteristics of the inflated cone in bending. The wrinkling factor is firstly defined so as to obtain the wrinkling condition. The initial wrinkling location is then determined by searching the maximum of the wrinkling factor. The critical wrinkling load is finally obtained by determining the ratio of the wrinkling moment versus the initial wrinkling location. The extremum method is proposed based on the assumption of membrane material of beam wall, and it is extended to consider beam wall with thin-shell material in the end. The nondimensional analyses show that the initial wrinkling location is closely related to the taper ratio. When the taper ratio is higher than the critical value, the initial wrinkles will be initiated at a different location. The nondimensional critical wrinkling load nonlinearly increases as the taper ratio increases firstly, and then linearly increases after the critical taper ratio. The critical taper ratio reflects the highest load-carrying efficiency of the inflated cone in bending, and it can be regarded as a measure to optimize the geometry of the inflated cone. The comparative analysis shows fairly good agreement between analytical and numerical results. Over the whole range of the comparison, the mean differences are lower than 3%. This gives confidence to use extremum method for bending-wrinkling analysis of inflated conical cantilever beam.

• Proceedings of the Computational Structural Engineering Institute Conference
• /
• 1999.04a
• /
• pp.268-275
• /
• 1999

The purpose of this study is to propose the method of determining the initial pneumatic membrane structures surface and stresses and displacements. Tension structure such as pneumatic membrane structures is stabilized by their initial prestress and air pressure. The process to find initial structural overall shape of tension structures produced by initial prestress called shape finding. One of the most important factor for the design of membrane structures is to search initial smooth surface, because unlike steel or concrete building elements which resist loads in bending, all tension structure forces are carried within the surface by membrane stress. The result for initial surface of pneumatic membrane element and maximum displacement in large deformation in analysis is compared with well-known nonlinear numerical method such as Newton-raphson method and dynamic relaxation method

• 한국공간정보시스템학회:학술대회논문집
• /
• 2004.05a
• /
• pp.83-88
• /
• 2004

First author proposed a proportioning method for member sections of a single layer reticulated dome subjected to uniform and non-uniform load without any geometrical initial imperfection, and discussed the validity and effectiveness of the method which was based on linear buckling stress and a knock down factor. However, buckling of a single layer reticulated dome is strongly affected by initial imperfection. It is well known that geometrical initial imperfections reduce the nonlinear buckling capacity of a single layer raticulated dome. Thus, structural engineers may be recommended to reflect the effects of geometrical initial imperfections in proportioning member sections. In this paper, firstly, the presented proportioning method by first author is applied to dome without consideration of any imperfections and the thickness and diameter of each member are determined. Secondly, the load bearing capacities of the proportioned domes are checked with the imperfection, by the inelastic buckling analysis.

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.26 no.11
• /
• pp.2415-2420
• /
• 2002

In the present study, a new anchor design was proposed to minimize the initial deflection of micro multi-layer cantilever beam with step-up structure, which is a key component of thin film micro-mirror array. It is important to minimize the initial deflection, caused by residual stress, because it reduces the performance of the actuation. Theoretical and experimental studies were conducted to examine the cause of the initial bending deflection. It was found that the bending deflection at the anchor of the cantilever beam was the primary source of initial deflection. Various anchor designs were proposed and the initial deflections for each design were calculated by finite element analysis. The analysis results were compared with experiments. To reduce the initial deflection a secondary support was added to the conventional structure. The optimal shapes were obtained by simulation and experiment. It was found from the analysis that the ratio or horizontal and vertical dimensions of secondary support was the governing factor, which affected the initial deflection.

• Journal of Korean Neurosurgical Society
• /
• v.62 no.2
• /
• pp.256-262
• /
• 2019

Objective : Pituitary adenomas (PAs) are often detected as incidental findings. However, the natural history remains unclear. The objective of this study was to evaluate the natural history and growth pattern of untreated PAs. Methods : Between 2003 and 2014, 59 PAs were managed with clinico-radiological follow up for longer than 12 months without any kind of therapeutic intervention. Tumor volumes were calculated at initial and last follow-up visit, and tumor growth during the observation period was determined. Data were analyzed according to clinical and imaging characteristics. Results : The mean initial and last tumor volume and diameter were $1.83{\pm}2.97mL$ and $13.77{\pm}6.45mm$, $2.85{\pm}4.47mL$ and $15.75{\pm}8.08mm$, respectively. The mean annual tumor growth rate was $0.33{\pm}0.68mL/year$ during a mean observation period of $46.8{\pm}32.1months$. Sixteen (27%) PAs showed tumor growth. The initial tumor size (HR, 1.140; 95% confidence interval, 1.003-1.295; p=0.045) was the independent predictive factor that determined the tumor growth. Six patients (11%) of 56 conservatively managed non-symptomatic PAs underwent resection for aggravating visual symptoms with mean interval of 34.5 months from diagnosis. By Cox regression analysis, PAs of last longest diameter over 21.75 mm were a significant prognostic factor for eventual treatment. Conclusion : The initial tumor size of PAs was independently associated with the tumor growth. Six patients (11%) of conservatively managed PAs were likely to be treated eventually. PAs of last follow-up longest diameter over 21.75 mm were a significant prognostic factor for treatment. Further studies with a large series are required to determine treatment strategy.

• 제어로봇시스템학회:학술대회논문집
• /
• 2002.10a
• /
• pp.116.6-116
• /
• 2002

$\textbullet$ Concept of Adaptive Scaling Factor $\textbullet$ Initial Value and Boundary Conditions $\textbullet$ Adaptive Scaling Factor $\textbullet$ Simulation and Experimental Results

• Journal of Mechanical Science and Technology
• /
• v.16 no.12
• /
• pp.1594-1603
• /
• 2002

In this paper, when the initial propagation angle of a branched crack is calculated from the maximum tangential stress criterion (MTSC) and the minimum strain energy density criterion (MSEDC), it is essential that you use stress components in which higher order terms are considered and stress components at the position in a distance 0.005㎜ from the crack tip (=r). When an interfacial crack propagates along the interface at a constant velocity, the initial propagation angles of the branched crack are similar. to the mode mixities (phase angle) and the theoretical values obtained from MTSC and MSEDC. The initial propagation angle of the branched crack depends considerably on the stress intensity factor K$_2$.

• Journal of the Korean Home Economics Association
• /
• v.49 no.6
• /
• pp.13-22
• /
• 2011

This study investigated the influence of product attribute on initial trust and purchase intention of sensor-based smart clothing. Questionnaires were administered to 256 university students in Daegu, Korea. The results were as follows: First, there were 5 factor solutions in product attribute of smart clothing; comfortableness, health usefulness, management easiness, safety, and aesthetic appearance. Second, there were significant effects on initial trust in heath usefulness, management easiness and safety. Third, there were significant effects on purchase intention in health usefulness, management easiness and aesthetic appearance. Fourth, there was a significant effect on purchase intention in initial trust.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2000.05b
• /
• pp.86-90
• /
• 2000

In this study, A equipment for measuring the initial permeability of soft-ferrite powder was developed by using a differential transformer coil, and was investigated demagnetizing factors. To measure the initial permeability of magnetic ceramic powder is cumbersome since there are not any measuring equipment and method. Magnetic powder is currently used for a magnetic fluid and microwave absorber materials, and the initial permeability of the magnetic powder is very important to be evaluated a powder for some applications.