• Journal of Electrical Engineering and Technology
• /
• v.9 no.5
• /
• pp.1753-1761
• /
• 2014

Due to the inherent inhomogeneous and anisotropy nature of the composite materials, the detection of internal defects in these materials with non-destructive techniques is an important requirement both for quality checks during the production phase and in service inspection during maintenance operations. The estimation of the time-of-arrival (TOA) and/or time-of-flight (TOF) of the ultrasonic echoes is essential in ultrasonic non-destructive testing (NDT). In this paper, we used split-spectrum processing (SSP) combined with matching pursuit signal decomposition (MPSD) to develop a dedicated ultrasonic detection system. SSP algorithm is used for Signal-to-Noise Ratio (SNR) enhancement, and the MPSD algorithm is used to decompose backscattered signals into a linear expansion of chirplet echoes and estimate the chirplet parameters. Therefore, the combination of SSP and MPSD (SSP-MPSD) presents a powerful technique for ultrasonic NDT. The SSP algorithm is achieved by using Gaussian band pass filters. Then, MPSD algorithm uses the Maximum Likelihood Estimation. The good performance of the proposed method is experimentally verified using ultrasonic traces acquired from three specimens of carbon fibre reinforced polymer multi-layered composite materials (CFRP).

• Korean Journal of Metals and Materials
• /
• v.48 no.12
• /
• pp.1103-1108
• /
• 2010

We fabricated flanged outer races for wheel bearing units using 0.52%C clean steels, and then characterized and studied the transformation behavior. The outer races produced by hot forging and high frequency induction hardening in this study were analyzed through microstructural characterization using OM, SEM, TEM, and X-ray diffractometer and their microhardness depth profiles of the raceway contacted by balls were measured using MVH tester. The surface hardened layers with a uniform hardness profile in the raceway consisting of very fine martensite with sub-micron sized retained austenite could be formed for very short time during high frequency induction hardening after hot forging. The very fine martensite may be transformed on rapid cooling, from the inhomogeneous austenite nucleated on rapid heating in small particles of pearlitic cementite fragmentated by hot forging. On the other hand the sub-micron sized retained austenite may be chemically stabilized due to their extremely small size, from the small austenite nucleated at the grain boundaries.

• Journal of Powder Materials
• /
• v.28 no.5
• /
• pp.375-380
• /
• 2021

In this study, we investigate the effect of the duration of mechanical alloying on the microstructures and mechanical properties of ODS ferritic/martensitic steel. The Fe(bal.)-10Cr-1Mo pre-alloyed powder and Y₂O₃ powder are mechanically alloyed for the different mechanical alloying duration (0 to 40 h) and then constantly fabricated using a uniaxial hot pressing process. Upon increasing the mechanical alloying time, the average powder diameter and crystallite size increased dramatically. In the initial stages within 5 h of mechanical alloying, inhomogeneous grain morphology is observed along with coarsened carbide and oxide distributions; thus, precipitate phases are temporarily observed between the two powders because of insufficient collision energy to get fragmented. After 40 h of the MA process, however, fine martensitic grains and uniformly distributed oxide particles are observed. This led to a favorable tensile strength and elongation at room temperature and 650℃.

• Journal of Powder Materials
• /
• v.20 no.4
• /
• pp.245-252
• /
• 2013

This study attempted to manufacture a Cu-Ga coating layer via the cold spray process and to investigate the applicability of the layer as a sputtering target material. In addition, changes made to the microstructure and properties of the layer due to annealing heat treatment were evaluated, compared, and analyzed. The results showed that coating layers with a thickness of 520 mm could be manufactured via the cold spray process under optimal conditions. With the Cu-Ga coating layer, the ${\alpha}$-Cu and $Cu_3Ga$ were found to exist inside the layer regardless of annealing heat treatment. The microstructure that was minute and inhomogeneous prior to thermal treatment changed to homogeneous and dense with a more clear division of phases. A sputtering test was actually conducted using the sputtering target Cu-Ga coating layer (~2 mm thickness) that was additionally manufactured via the cold-spray coating process. Consequently, this test result confirmed that the cold sprayed Cu-Ga coating layer may be applied as a sputtering target material.

• Progress in Superconductivity
• /
• v.8 no.2
• /
• pp.169-174
• /
• 2007

We measured the field profiles, H(x)'s of coated conductors by using scanning Hall probe method when various magnetic fields, $H{_\alpha}'s$ or currents, I's were applied. From the measured field profiles, we calculated the current profiles, J(x)'s by the inversion method. The calculated J(x)'s of coated conductors show some different properties from the standard critical state model. $J{_c}'s$ are inhomogeneous varying with the positions and are not constant when $H_{\alpha}$ or I changes. And when I decreases the features of current reversion are remarkably different from the model.

• Journal of Welding and Joining
• /
• v.25 no.3
• /
• pp.37-44
• /
• 2007

Mechanical and thermomechanical properties of the bulk metallic glass (BMG) are so unique that the deformation behavior is largely dependent on the temperature and the strain rate. Impacting behavior of NiTiZrSiSn bulk metallic glass powder during kinetic spraying was investigated in this study. Considering the impact behavior of the BMG, the kinetic spraying system was modified and attached the powder preheating system to make the transition from the inhomogeneous deformation to the homogeneous deformation of impacting BMG particle easy BMG splat formation is considered from the viewpoint of the adiabatic shear instability. It is suggested that the impact behavior of bulk metallic glass particle is determined by the competition between fracture and deformation. The bonding of the impacting NiTiZrSiSn bulk amorphous particle was primarily caused by the temperature-dependent deformation and fracture (local liquid formation) behavior.

• Journal of the Korean Society of Manufacturing Process Engineers
• /
• v.20 no.1
• /
• pp.42-47
• /
• 2021

Recently, many structures using lightweight materials have been developed. This study was conducted by using Al6061-T6 and carbon fiber reinforced plastic (CFRP), two common lightweight materials. In addition, the failure characteristics of an interface bonded between a single material and a heterogeneous bonding material were analyzed. The specimens bonded with CFRP and Al6061-T6 were utilized by the combination of the heterogeneous bonding material. The specimens had a double cantilevered shape and the bonding between the materials was achieved by applying a structural adhesive. The experiments were conducted in opening mode: the lower part of the samples was fixed, while their upper part was subjected to a forced displacement of 3 mm/min by using a tensile tester. Under the tested amount of strength, energy release rate, and considering the specimens' fracture characteristics in opening mode, the specimen "CFRP-Al" presented the maximum stress, followed by "Al" and "CFRP". We can hence conclude that the inhomogeneous material "CFRP-Al" is useful for the construction of lightweight structures bonded with structural adhesive.

• Journal of Radiation Protection and Research
• /
• v.34 no.4
• /
• pp.176-183
• /
• 2009

Maintenance on the water chamber of steam generator during outage in nuclear power plants (NPPs) has a likelihood of high radiation exposure to whole body of workers even short time period due to the high radiation exposure rates. In particular, it is expected that hands would receive the highest radiation exposure because of its contact with radiation materials. In this study, characteristic analysis of inhomogeneous radiation fields for contact operations was conducted using thermoluminescent dosimeter (TLD) readouts from the application tests of two-dosimeter algorithm to Korean NPPs in 2004. It is regarded that inhomogeneous radiation fields for contact operations in NPPs are dominated by high energy photons. In addition, field tests for workers who participated in maintenance on the steam generator during outage at Ulchin NPPs in 2009 and pressure tube replacement at Wolsong NPPs in 2009 were conducted to analyze radiation fields and to estimate the extremity dose. As a result, radiation fields were dominated by high energy photons.

• Journal of the Korean institute of surface engineering
• /
• v.53 no.6
• /
• pp.330-342
• /
• 2020

Since the original report on ferroelectricity in Si-doped HfO2 in 2011, fluorite-structured ferroelectrics have attracted increasing interest due to their scalability, established deposition techniques including atomic layer deposition, and compatibility with the complementary-metal-oxide-semiconductor technology. Especially, the emerging fluorite-structured ferroelectrics are considered promising for the next-generation semiconductor devices such as storage class memories, memory-logic hybrid devices, and neuromorphic computing devices. For achieving the practical semiconductor devices, understanding polarization switching kinetics in fluorite-structured ferroelectrics is an urgent task. To understand the polarization switching kinetics and domain dynamics in this emerging ferroelectric materials, various classical models such as Kolmogorov-Avrami-Ishibashi model, nucleation limited switching model, inhomogeneous field mechanism model, and Du-Chen model have been applied to the fluorite-structured ferroelectrics. However, the polarization switching kinetics of fluorite-structured ferroelectrics are reported to be strongly affected by various nonideal factors such as nanoscale polymorphism, strong effect of defects such as oxygen vacancies and residual impurities, and polycrystallinity with a weak texture. Moreover, some important parameters for polarization switching kinetics and domain dynamics including activation field, domain wall velocity, and switching time distribution have been reported quantitatively different from conventional ferroelectrics such as perovskite-structured ferroelectrics. In this focused review, therefore, the polarization switching kinetics of fluorite-structured ferroelectrics are comprehensively reviewed based on the available literature.

• 기계와재료
• /
• v.23 no.3
• /
• pp.16-29
• /
• 2011

결정 합금 대비 비정질 합금은 높은 경도를 갖기 때문에 마모 저항성도 좋고 내부 식성 등 환경에 대한 저항성도 월등하며, 또한 과냉된 액상 상태까지 재가열하게 되면 낮은 점성도를 갖게 되므로 복잡한 3차원적인 형상을 가지는 부품을 환경에 대한 저항성, 피로 저항성, 강도 및 경도 등을 모두 고려하여 높은 정밀도를 가지고 제조하는 것이 가능하므로 우수한 물성을 갖는 구조 및 기능성 재료로의 다양한 응용이 타진되고 있다. 이러한 비정질 합금의 변형 거동에 대한 연구는 대부분 유리 천이 온도 이하에서의 전단 및 파단에 이르는 이른바 불균일 변형(Inhomogeneous Deformation) 거동에 대한 이해를 위한 실험 및 해석적 연구에 집중되어 왔다. 반면 상업화의 기반이 되는 고상 기반 2차 정형 성형은 과냉 액상 영역에서의 구조 완화 및 결정화롤 대표되는 미세 구조 제어 균일 변형(Homogeneous Deformation)에 대한 이해 없이는 불가능하므로, 이러한 관점에서 비정질 합금 특유의 점성 유동 특성을 이용한 균일 변형 응용 예시 및 미세구조 변화 연계 해석 기술의 현황을 소개하고자 한다.