• Structural Engineering and Mechanics
• /
• v.76 no.4
• /
• pp.491-503
• /
• 2020

This study extends previous experimental research on the shear behaviour of macrosynthetic fibre-reinforced concrete beams and compares them to steel fibre-reinforced concrete beams with similar mechanical and geometrical properties. This work employed two fibre types: 60/0.9 (long/diameter) double hooked-end steel fibre and 60/85 monofilament polypropylene fibre. Beams were tested by shear loading covering parameters, such as two different cross-section widths, two shear-span-to-effective-depth ratios, two fibre types and using repetitions with and without transverse reinforcement. For quantitative comparison purposes, crack pattern evolution was studied along increasing loads levels. Effects were studied by photogrammetry, including influence of fibres on crack propagation in uncracked and dowel zones, influence of fibres on stirrup behaviour, and shear deformation or kinematics of critical shear cracks. The results evidenced similar effectiveness for both fibre types in controlling shear crack propagation and horizontal dowel cracking. Both fibres provided similar shear ductility and shear deflections. Consequently, the authors confirm that residual flexural tensile strengths are a convenient parameter for characterising the shear behaviour of fibre-reinforced concrete beams.

• 한국연소학회:학술대회논문집
• /
• 1998.10a
• /
• pp.139-154
• /
• 1998

Under certain circumstance, premixed turbulent flame can be treated as wrinkled thin laminar flame and its motion in a hydrodynamic flow field has been investigated by employing G-equation. Past studies on G-equation successfully described certain aspects of laminar flame propagation such as effects of stretch on flame speed. In those studies, flames were regarded as a passive interface that does not influence the flow field. The experimental evidences, however, indicate that flow field can be significantly modified by the propagation of flames through the volume expansion of burned gas. In the present study, a new method to be used with G -equation is described to include the effect of volume expansion in the flame dynamics. The effect of volume expansion on the flow field is approximated by Biot-Savart law. The newly developed model is validated by comparison with existing analytical solutions of G -equation to predict flames propagating in hydrodynamic flow field without volume expansion. To further investigate the influence of volume expansion, present method was applied to initially wrinkled or planar flame propagating in an imposed velocity field and the average flame speed was evaluated from the ratio of flame surface area and projected area of unburned stream channel. It was observed that the initial wrinkling of flame cannot sustain itself without velocity disturbance and wrinkled structure decays into planar flame as the flame propagates. The rate of decay of the structure increased with volume expansion. The asymptotic change in the average burning speed occurs only with disturbed velocity field. Because volume expansion acts directly on the velocity field, the average burning speed is affected at all time when its effect is included. With relatively small temperature ratio of 3, the average flame speed increased 10%. The combined effect of volume expansion and flame stretch is also considered and the result implied that the effect of stretch is independent of volume release.

• KSII Transactions on Internet and Information Systems (TIIS)
• /
• v.15 no.4
• /
• pp.1263-1274
• /
• 2021

In online competitive social networks, each user can be influenced by different competing influencers and consequently chooses different products. But their interest may change over time and may have swings between different products. The existing influence spreading models seldom take into account the time-related shifts. This paper proposes a minimum cost influence maximization algorithm based on the competitive transition probability. In the model, we set a one-dimensional vector for each node to record the probability that the node chooses each different competing influencer. In the process of propagation, the influence maximization on Competitive Linear Threshold (IMCLT) spreading model is proposed. This model does not determine by which competing influencer the node is activated, but sets different weights for all competing influencers. In the process of spreading, we select the seed nodes according to the cost function of each node, and evaluate the final influence based on the competitive transition probability. Experiments on different datasets show that the proposed minimum cost competitive influence maximization algorithm based on IMCLT spreading model has excellent performance compared with other methods, and the computational performance of the method is also reasonable.

• Proceedings of the Plant Resources Society of Korea Conference
• /
• 2019.10a
• /
• pp.40-40
• /
• 2019

는쟁이냉이는 전국 각지 산지의 응달이나 물가에서 자생하는 여러해살이풀이다. 3월 경 눈을 뚫고나와 가장 이른 봄나물로 식용하기도 한다. 특유의 매운 맛이 있어 식용작물로 발전가능성이 높은 식물종이다. 따라서 본 연구는 는쟁이냉이 재배기술 정립을 위한 기초자료 수집의 일환으로 수행되었다. 차광에 따른 는쟁이냉이 생육특성을 비교 분석하기 위해 경북 봉화군 소재 국립백두대간수목원 양묘장 노지에 무차광, 40% 차광, 55%차광, 65%차광 처리구를 배치 후, 실험을 진행하였다. 생육특성의 비교를 위해 초장, 초폭, 엽 수, 엽길이, 엽너비, 엽병길이, SPAD 값 총 7가지 항목에 대해 생장기(6월), 휴면기(9월) 두 차례 측정하였다. 측정 결과, 모든 측정값이 차광구가 무차광구보다 높게 나타났다. 또한 무차광구는 6월 조사 이후, 7월 말까지 생장량이 줄어들다가 전량 지상부 고사가 발생하여 는쟁이냉이 재배를 위해서는 차광처리가 필수적으로 필요하다는 것을 확인할 수 있었다. 측정항목 중 초장, 초폭, 엽길이, 엽너비, 엽병길이는 차광율이 높을수록 증가하는 경향을 보였다. 그러나 엽록소함량을 추정할 수 있는 SPAD 값은 40% 차광구가 가장 높았고 55%차광구, 65%차광구에서는 오히려 감소하는 경향을 보였다. 또한 엽 수도 40% 차광구가 가장 높았다. 위 결과를 종합해볼 때, 는쟁이냉이 재배 시 55% 이상의 차광율을 적용하면 잎 자체의 크기 증대를 기대할 수 있으며, 40% 수준의 차광율을 적용하면 잎 수와 혁질의 잎을 생산할 수 있을 것으로 여겨진다. 다만, 본 실험은 는쟁이냉이 재배 생산량에 대한 부분에 집중하였고 상품화를 위해서는 품질에 관한 연구가 추가적으로 이루어져야 할 것으로 판단된다.

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.39 no.1
• /
• pp.63-69
• /
• 2015

The primary aim of this paper is to evaluate the probabilistic fatigue crack propagation models using the residual of a random variable and to present the probabilistic model fit for the probabilistic fatigue crack growth behavior in Mg-Al-Zn alloys under maximum load conditions. The models used in this study were prepared by applying a random variable to empirical fatigue crack propagation models such as the Paris-Erdogan model, Walker model, Forman model, and modified Forman model. It was verified that the good models for describing the stochastic variation of the fatigue crack propagation behavior in Mg-Al-Zn alloys under maximum load conditions were the 'probabilistic Paris-Erdogan model' and 'probabilistic Walker model'. The influence of the maximum load conditions on the stochastic variation of fatigue crack growth is also considered.

• Magazine of the Korean Society of Agricultural Engineers
• /
• v.18 no.1
• /
• pp.4021-4037
• /
• 1976

This paper describes the actual experiments of the error propagation and studies of analytical photogrammetry using the simulation method in which we can find the causes of the errors. These studies and the results give the valuable data which are very effective for systematically controlling the errors in aerial triangulation. The main contents in my paper are as follows: 1. Dose the scale errors in the successive models in the form of normal distribution appear when the observation errors propagate in the form of normal distribution\ulcorner 2. In what form does this scale error propagation in the actual model appear\ulcorner 3. When the causes of the scale error propagation are found, is the evaluation standard determined normally\ulcorner 4. What degree of influence is there form the constant errors\ulcorner I have done several experiments using the simulation method technique to solve the complicated error propgation of aerial triangulation which is the effective means to research the relations between cause and effect. In this paper, the studies have concentrated on the following points of simulation experiments. (1) The first part descries how we can produce the soft program of the simulation experiment. (2) The second part is the method propagating the errors in the simulation models and the kinds of errors. (3) The final part is the most important; that is the analyzing and evaluation of control during actual work. From the above-mentioned points, it is said that these studies are a very important development in the field of controlling and managing aerial photogrammetry and especially in the case of error propagation, we can clearly find the causes of the errors and steps and parts of errors generated when we use these techniques.

• Transactions of the Korean Society of Mechanical Engineers B
• /
• v.38 no.2
• /
• pp.173-181
• /
• 2014

The propagation behavior and structural variation of a premixed propane/air flame with frequency change in an ultrasonic standing wave at various equivalence ratios were experimentally investigated using Schlieren photography and pressure measurement. The propagating flame was observed in high-speed Schlieren images, allowing local flame velocities of the moving front to be analyzed in detail. The study reveals that the distorted flame front and horizontal splitting in the burnt zone are due to the ultrasonic standing wave. Vertical locations of the distortion and horizontal stripes are intimately dependent on the frequency of the ultrasonic standing wave. In addition, the propagation velocity of the flame front bounded by the standing wave is greater than that of the flame front without acoustic excitation. As expected, the influence of the ultrasonic standing wave on premixed-flame propagation becomes more prominent as the frequency increases.

• Journal of the Computational Structural Engineering Institute of Korea
• /
• v.20 no.2
• /
• pp.95-103
• /
• 2007

An analytical closed-form solution for wave propagation velocity and damping in saturated porous media is presented in this paper The fully coupled field model with compressible solid Brains and pore water were used to derive this solution. An engineering approach for the analysis of fully saturated porous media was adopted and closed-form solutions for one dimensional wave propagation in a homogeneous domain were derived. The solution is highly versatile in that it considers compression of the solid grains, compression of the pore water, deformation of the porous skeleton, and spatial damping and can be used to compute wavespeeds of first and second kind and damping coefficients in various geologic materials. This solution provides a means of analyzing the influence of material property variations on wavespeed and attenuation. In Part 2 of this work the theoretical solution is incorporated into the numerical code and the code is used in a parametric study on wave propagation velocity and damping.

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.38 no.4
• /
• pp.401-407
• /
• 2014

In this paper, the effect of cohesive laws on the finite element analysis of crack propagation using cohesive elements is investigated through three-point bending and double cantilever beam problems. The cohesive elements are implemented into ABAQUS/Standard user subroutines(UEL), and the shape of cohesive law is varied by changing parameters in polynomial functions of cohesive traction-separation relations. In particular, crack propagation behaviors are studied by comparing load-displacement curves of the analysis models which have different shapes of cohesive laws with the same values of fracture energy and cohesive strength. Furthermore, the influence of the element size on crack propagation is discussed in this study.

• Laser Solutions
• /
• v.9 no.2
• /
• pp.1-9
• /
• 2006

In this paper, we investigated the characteristics of fatigue fracture on TB(Tailored Blank) weldment by comparing the fatigue crack propagation characteristics of base metal with those of TB welded sheet used for vehicle body panels. We also investigated the influence of center crack on the fatigue characteristic of laser weld sheet of same thickness. We conducted an experiment on fatigue crack propagation on the base metal specimen of 1.2mm thickness of cold-rolled metal sheet(SPCSD) and 2.0mm thickness of hot-rolled metal sheet(SAPH440) and 1.2+2.0mm TB specimen. We also made an experiment on fatigue crack propagation on 2.0+2.0mm and 1.2+1.2mm thickness TB specimen which had center crack. The characteristics of fatigue crack growth on the base metal were different from those on 1.2+2.0mm thickness TB specimen. The fatigue crack growth rate of the TB welded specimens is slower in low stress intensity factor range $({\Delta}K)$ region and faster in high${\Delta}K$ region than that of the base metal specimens. The slant crack angle slightly influenced the crack propagation of the TB specimen of 2.0+2.0mm thinkness.