• 대한산업공학회지
• /
• 제33권3호
• /
• pp.381-392
• /
• 2007

In this paper, we present an analytical method for estimating the saturation throughput of an 802.11 ad hoc LAN in the presence of noise distorting transmitted frames. This is the first method that allows studying analytically the 802.11 network performance with consideration of correlated channel failures usually inherent to realistic wireless channels. With the study, we consider the possible packet fragmentation that can be adopted to reduce the performance degradation caused by noise-induced distortions. In addition to the throughput, our method allows estimating the probability of a packet rejection occurring when the number of packet transmission retries attains its limit. The obtained numerical results of investigating 802.11 LANs by the developed method are validated by simulation and show high estimation accuracy as well as the method efficiency in determining the optimal fragmentation threshold.

• 대한전자공학회논문지SP
• /
• 제46권1호
• /
• pp.56-62
• /
• 2009

산업용 강판튜브 CR영상의 잡음특성과 기하학적 구조에 관한 해석적 접근을 시도한다. 산업현장에서 방사선 측정실험으로 직접 취득한 방사선영상을 방사선강도에 따라 30(개) 이상의 샘플을 수집하였다. 이들 각 영상은 배경부, 두께부 및 튜브내부의 세 영역으로 구성되었는바, 그 가운데 튜브내부영역을 분석 대상으로 삼았다. 통계적이고 함수적인 방법론에 의해 잡음특성을 포함한 기하학적 구조를 분석한다. 영상을 구성하는 화소라인별로 또는 공간적으로 분석을 수행하여 강판튜브의 기하학적 원형 형태가 방사선영상화 과정을 거치면서 일어나는 변형과 잡음속성 변화의 두 가지 특성을 규명한다. 분석시 부합함수와 그 오차를 기하학적 변형의 판별인자로, 표준편차, 평균 및 SN비를 잡음특성 판별인자로 설정하고 방사선투과정도의 영상에서의 실현인 회색도 변화에 따른 이들 인자들의 변화를 고찰하였다. 분석결과, 본래의 원형 구조가 방사선투과 강도에 따라 타원형에서 저반경 원형 그리고 고반경원형의 점차적인 구조 변형을 일으킨다는 사실을 밝혔고, 잡음의 편차가 투과강도에 반비례함을 규명하였다.

• Journal of Preventive Medicine and Public Health
• /
• 제4권1호
• /
• pp.41-64
• /
• 1971

During the period from July 1st to the end of November 1970, a survey on air pollution and noise level was made in Seoul, Pusan and Taegu, the three largest cities in Korea. Each city was divided into 4-6 areas; the industrial area, the semi-industrial area, the commercial area, the residential area, the park area and the downtown area. Thirty eight sites were selected from each area. A. Method of Measurement : Dustfall was measured by the Deposit Gauge Method, sulfur oxides by $PbO_2$ cylinder method, suspended particles by the Digital Dust Indicator, Sulfur dioxide ($SO_2$) and Carbon Monoxide (CO) by the MSA & Kitakawa Detector and the noise levels by Rion Sound Survey meter. B. Results: 1. The mean value of dustfall in 3 cities was $30.42ton/km^2/month$, ranging from 8.69 to 95.44. 2. The mean values of dustfall by city were $33.17ton/km^2/month$ in Seoul, 32.11 in Pusan and 25.97 in Taegu. 3. The mean values of dustfall showed a trend of decreasing order of semi-industrial area, downtown area, industrial area, commercial area, residential area, and park area. 4. The mean value of dustfall in Seoul by area were $52.32ton/km^2/month$ in downtown, 50.54 in semi-industrial area, 40.37 in industrial area, 24,19 in commercial area, 16.25 in park area and 15.39 in residential area in order of concentration. 5. The mean values of dustfall in Pusan by area were $48.27ton/km^2/month$ in semi-industrial area, 36.68 in industrial area 25.31 in commercial area, and 18.19 in residential area. 6. The mean values of dustfall in Taegu by area were $36.46ton/km^2/month$ in downtown area, 33.52 in industrial area, 20.37 in commercial area and 13.55 in residential area. 7. The mean values of sulfur oxides in 3 cities were $1.52mg\;SO_3/day/100cm^2\;PbO_2$, ranging from 0.32 to 4.72. 8. The mean values of sulfur oxides by city were $1.89mg\;SO_3/day/100cm^2\;PbO_2$ in Pusan, 1.64 in Seoul and 1.21 in Taegu. 9. The mean values of sulfur oxides by area in 3 cities were $2.16mg\;SO_3/day/100cm^2\;PbO_2$ in industrial area, 1.69 in semi-industrial area, 1.50 in commercial area, 1.48 in downtown area, 1.32 in residential area and 0.94 in the park area, respectively. 10. The monthly mean values of sulfur oxides contents showed a steady increase from July reaching a peak in November. 11. The mean values of suspended particles was $2.89mg/m^3$, ranging from 1.15 to 5.27. 12. The mean values of suspended particles by city were $3.14mg/m^3$ in Seoul, 2.79 in Taegu and 2.25 in Pusan. 13. The mean values of noise level in 3 cities was 71.3 phon, ranging from 49 to 99 phon. 14. The mean values of noise level by city were 73 phon in Seoul, 72 in Pusan, and 69 in Taegu in that order. 15. The mean values of noise level by area in 3 cities showed a decrease in the order of the downtown area, commercial area, industrial area and semi-industrial area, park area and residential area. 16. The comparison of the noise levels by area in 3 cities indicated that the highest level was detected in the downtown area in Seoul and Taegu and in the industrial area in Pusan. 17. The daily average concentration of sulfur dioxides ($SO_2$) in 3 cities was 0.081 ppm, ranging from 0.004 to 0.196. 18. The daily average concentrations of sulfur dioxides by city were 0.092 ppm in Seoul, 0.089 in Pusan and 0.062 in Taegu in that order. 19. The weekly average concentration of carbon monoxides(CO) was 27.59 ppm. 20. The daily average concentrations of carbon monoxides by city were 33.37 ppm. in Seoul, 25.76 in Pusan and 23.65 in Taegu in that order. 21. The concentration of $SO_2$ and CO reaches a peak from 6 p. m. to 8 p. m. 22. About 3 times probably the daily average concentration of CO could be detected in the downtown area probably due to heavy traffic emission in comparison with that in the industial area. 23. As for daily variation of the concentration of $SO_2$ and CO it was found that the concentration maintains relatively higher value during weekdays in the industrial area and on the first part of the week in the downtown area.

• 한국산학기술학회논문지
• /
• 제19권10호
• /
• pp.401-409
• /
• 2018

본 연구는 패스(Path) 제어방법을 적용하여 소형전술차량에 적용된 NSD의 소음을 저감하기 위한 것이다. 소형전술차량은 고기동성 확보를 위해 후차축에 차동제한장치 중 하나인 NSD를 적용하였다. NSD는 높은 제한율을 가져 기동성을 향상 시켜주지만 기계적 구조에 의해 특정 조건에서 소음이 발생되는 단점이 있다. 이 소음은 NSD가 차동장치로써 원활한 역할 수행을 위해 기어간 유격에 의해 치간 접촉에 따라 발생되는 소음이다. 이러한 소음이 지속적으로 사용자에게 전달됨에 따라 운용자가 지속적인 문제 제기 및 개선 요구를 하고 있다. 물론, NSD의 소음으로 인해 제품의 성능 또는 내구성에 미치는 영향은 없으며, 국방규격에서 규정하는 소음 조건 역시 만족한다. 하지만, 사용자의 지속적인 개선요구에 따라 소음저감을 위한 방안에 대해 연구를 수행하였다. 따라서, 본 연구에서는 소음원의 제거가 현실적으로 제한되는 전술차량의 NSD 소음을 감소하기 위해 NSD의 소음이 전달되는 경로를 제어하는 패스제어방법을 적용하였다. 이를 통해 구조 전달계를 개선 보완하고 이에 대한 개선효과를 검증하고자 한다.

• Journal of Advanced Marine Engineering and Technology
• /
• 제18권1호
• /
• pp.81-91
• /
• 1994

Combustion noise involved with chemical heat release and turbulent process in turbopropulsion systems, gasturbine, industrial furnaces and internal engines is indeed noisy. The experimental study reported in this paper is made to identify a dominant combustion noise in jet flames. Gaseous propane and kerosene fuel have been used with air as the oxidizer in a different jet combustion systems. Combustion and aerodynamic noise are studied through far field sound pressure measurements in an anechoic chamber. And also mean temperature and velocities and turbulent intensities of both isothermal and reacting flow fields were measured. It is shown that axial mean velocity of reacting flow fields is higher about 1 to 3m/sec than that of cold flow in a gaseous combustor. As the gaseous fuel flow rate increases, the acoustic power increases. But the sound pressure level for the spray flame decreases with increasing equivalence ratio. The influence of temperature in the combustion fields due to chemical heat release has been observed to be a dominant noise source in the spray flame. The spectra of combustion noise in gaseous propane and kerosene jet flame show a predominantly low frequency and a broadband nature as compared with the noise characteristics in an isothermal air jet.

• 한국정보통신학회논문지
• /
• 제17권7호
• /
• pp.1725-1731
• /
• 2013

최근 산업사회가 고도의 디지털 정보화 시대로 발전함에 따라 영상처리는 여러 분야에 활용되고 있다. 그러나 여전히 데이터를 처리하는 과정에서 다양한 잡음에 의해 영상의 열화가 발생하며, 잡음을 제거하기 위해 여러 가지 방법의 연구가 진행되고 있다. 따라서 본 논문에서는 임펄스 잡음을 제거하기 위해, 표준편차를 이용한 변형된 메디안 필터를 제한하였다. 제안한 알고리즘은 잡음판단과 잡음제거 두 부분으로 나누며, 비 잡음 신호는 그대로 보존하고, 잡음 신호는 필터처리 한다. 그리고 객관적 판단을 위해 기존의 방법들과 비교하였으며, 판단의 기준으로 PSNR(peak signal to noise ratio)을 사용하였다.

• 한국소음진동공학회논문집
• /
• 제20권11호
• /
• pp.1089-1096
• /
• 2010

The relation between the vibration induced from machinery and the radiated sound is complicated. Acoustic intensity method is widely used to obtain the accuracy of noise measurement and noise identification. In this study, as groundwork, the complex acoustic intensity method is performed to identify noise source and transmission path on different free space point source fields. As an industrial application, the complex acoustic intensity method is applied to HVAC to identify sound radiation characteristics in the near field. Experimental complex acoustic intensity method was applied to HVAC, it is possible to identify noise sources in complicated sound field characteristics which noise sources are related with each other, and certificate the validity of complex acoustic intensity. Especially, it can be seen that complex acoustic intensity method using both of active and reactive intensity is vital in devising a strategy for identification of noise. Also, the vector flow of acoustic intensity was investigated to identify sound intensity distributions and energy flow in the near field of HVAC.

• International Journal of Safety
• /
• 제3권1호
• /
• pp.6-9
• /
• 2004

This paper deals with the noise evaluation technique of a reciprocating air-compressor and its noise reduction. The reciprocating air-compressors are widely used in the small, medium sized industrial firms, and lots of their employees are affected and irritated by their noise in the workplace. Thus, noise control actions should be taken appropriately by considering the hearing loss due to the occupational noise exposure. Lead-wrapping techniques are employed to identify the contribution of principal noise sources which are generally known as motor, belts, suction/discharge valves, moving pistons, and flow-induced noise caused by edges or discontinuities along the flow path e.g. expansions, contractions, junctions and bends etc .. As a result, main noise sources of the air-compressor can be categorized by the suction/discharge noise, valve noise, and compressed-air tank noise. Based on the investigations, mufflers are designed to reduce both the suction/discharge noise and the compressed-air tank noise. Instead of the conventional valve plate, polyethylene resin is used as a new one for the reduction of valve impact noise. In addition, attempts are made to reduce the valve noise propagation to the cylinder head and the compressor tank by using the insulation casings. As a result of the countermeasure plans, it can be achieved that the noise reduction of the air-compress is up to 10dB.

• 한국산학기술학회논문지
• /
• 제19권2호
• /
• pp.639-643
• /
• 2018

전자 시스템이 소형화, 이동성의 요구에 따라 전력 변환의 필요성이 계속 증가하고 있다. 또한 전력 변환에는 전력 효율과 함께 전력 변환시스템의 소형화를 위해 적용하는 스위칭에 의한 잡음으로부터 시스템 안정성이 보장되어야 한다. 따라서 전력 변환시 스위칭 잡음을 감소시킬 수 있는 대책이 필수적이다. 본 논문에서는 DC/DC Buck Converter회로를 구성하였고, reference plane을 갖는 4층 PCB 회로 구조에서 부품의 배치를 변경할 경우 발생하는 스위칭 잡음특성을 비교 분석하였다. 또한, Reference Plane을 제거한 양면 PCB회로 구조에서 부품 배치를 달리하였을 경우 스위칭 잡음 특성을 각각 시뮬레이션으로 비교 분석하였다. 그 결과 4층 PCB회로 구조에서는 Current return path에 따라 Radiated Emission 특성이 12dB, Conducted Emission 특성이 7~8dB 감소됨을 확인하였다. 또한 양면 PCB회로 구조에서는 Conducted Emission이 20~25dB 감소됨을 확인하였다. 이로써 전력 변환 회로를 설계할 경우 Current return path의 구성에 따라 잡음 특성을 향상시킬 수 있음을 확인하였다.

• 한국산업보건학회지
• /
• 제15권2호
• /
• pp.135-143
• /
• 2005

This study was conducted to measure the exposure levels to noise for the middle and the high school students who worn headsets in the PC rooms. The noise levels from the headsets were measured with noise dosimeters, and the statistical relationships between the utilization pattern, user's views on the PC rooms and it's environment were analyzed for the selected PC rooms in the Ahnshan area. The results were as follows; 1. No significant difference was found in the number of uses and average time spent per day by education level and by sex of the users(p>0.05). 2. No statistical significant difference was found between the contents selected by education level of the users (p>0.05). The male participants overwhelmingly enjoyed the PC games (98.3 %) while females selected for listening music (75.0 %) with significant difference(P<0.05), followed by browsing internet and PC communications (70.0 %), PC game (66.7 %) and chatting (33.3 %). 3. The actual noise measurements of the headsets worn by the users of different sexes and educational backgrounds produced no differences(p>0.05), while a significant difference was found between genders (p<0.05). 4. For sound pressure level measurements, the weighted average(Lavg) of 84.5 dB(A) on the left headsets exceeded that of 79.8 dB(A) on the right headsets significantly(p<0.01) and the maximum value of 96.9 dB(A) on the left headsets exceeded the maximum value of 93.5 dB(A) on the right headsets(p<0.01). 5. The actual noise measurements of the headsets worn by the users of different sexes and educational backgrounds produced no differences(p>0.05), however, the contents selected by the users with different educational backgrounds were noted with significant difference(p<0.05) while no difference was found by gender(p>0.05).