• Journal of the Korea Institute of Building Construction
• /
• v.15 no.4
• /
• pp.359-365
• /
• 2015

Floor mortar experiences dry shrinkage by temperature and humidity difference of internal matrix with material type. Also, since floor mortar is influenced by environmental conditions during placing and curing period, cracks are likely to be occurred. In this study, it was evaluated the hardening and dry shrinkage properties of non-sintered binder based floor mortar utilizing alpha-hemihydrate gypsum which has expansibility in order to prevent crack of the floor mortar. It was applied to the construction site, and examined the effects of external environmental conditions on shrinkage deformation and cracking. Different types of slag accelerated initial and final setting in comparison with cement mortar and its compressive strength was satisfied standard compressive strength for floor mortar. Also shrinkage deformation behavior after the initial expansion exhibited a similar tendency with the cement mortar. From the field application result, no crack was found from slag mortar, and it is determined that the slag mortar has better dimensional stability than cement mortar caused by external environment conditions.

• Journal of the Korea Concrete Institute
• /
• v.17 no.2 s.86
• /
• pp.237-245
• /
• 2005

In this paper, the changes of the period of cold weather concrete in Korea with the elapse of age are discussed to investigate the influence of elapse of age on period of cold weather concrete. The climate data of Korean Meteorological Administration(KMA) ranging from 1971 to 2000 was used. The period of cold weather concrete was calculated by following the specification of Korea Concrete Institute(KCI), American Concrete Institute(ACI) and Architectural Institute of Japan(AIJ), respectively. Previous research by the authors used the climate dada of KMA from 1961 to 1990 and research conducted by Kim M.H. used the climate data from 1931 to 1980 were also compared with the period of present paper. According to the results, in present paper, the period of cold weather concreting by KCI was calculated about 95days on average and the period by ACI was 101 days on average and the period by AIJI was 92days on average. For the variation of the period with the elapse of time, the period of cold weather concrete by KCI and ACI in present paper was shortened by as much as 5${\~}$6days compared with that of previous paper 10years ago. However, the period of cold weather concreting by AIJ did not exhibit a marked reduction in the period compared with that of previous paper by the author. But the period by Kim following AIJ exhibited a decrease in the period compared to the period by present paper by as much as 3days. For regional influence, the period of cold weather concreting in southern part of Korea was found to be much shorter than those at northern part. This may be due to the rising of mean temperature caused by global warming effect.

• Journal of the Korea Institute of Building Construction
• /
• v.17 no.1
• /
• pp.47-54
• /
• 2017

Cement industry is typical carbon-emission industry. If the industrial by-products(granulated blast-furnace slag (GGBFS), fly ash, etc.) are used a large amount, it might be able to reduce cement consumption and mitigate carbon emissions. In this case, however, decrease of early strength is relatively large. Therefore, there is a limitation in increase of the amount of substitute. Considering these circumstances, it would be a good solution to reduce carbon emissions in cement industry to improve the performances of mixed cement through proper alkali-activation in Portland blended cement using GGBFS or fly ash. Therefore, this study prepared concrete in ready-mixed concrete manufacturing facilities with an addition of a binder which used 2.0% modified alkali sulfate activator after mixing Portland cement, GGBFS and fly ash in the ratio of 4:4:2 and assessed its basic properties. The results found the followings: The use of modified alkali-sulfate activator slightly reduced slump and shortened setting time. As a result, bleeding capacity decreased while early strength improved. In addition, there is no big difference in carbonation resistance. It appears that there should be continued experiments and analyses on the related long-term aged specimens.

• Korean Chemical Engineering Research
• /
• v.51 no.3
• /
• pp.407-410
• /
• 2013

The chlorination of a metallurgical-grade silicon was carried out in a fluidized bed reactor, 25 mm in diameter. The flow rate of the chlorine admitted into the reactor was 0.2 L/min and that of the carrier nitrogen was 0.8~1.0 L/min. The reactor temperature was maintained at $450^{\circ}C$ and the temperature of the coolant at the $SiCl_4$ condenser was at $-5^{\circ}C$. The $SiCl_4$ yield increased with increasing the mole fraction of chlorine in the feed gas, exhibiting 28% at the mole fraction of 0.2. Further increase of the chlorine mole fraction was not attempted in a worry that the reactor might be failed due to the high exothermicity of the reaction. The production of $SiCl_4$ from silicon by fluidized bed chlorination was demonstrated on a laboratory scale, which is a stepping stone for future studies under more severe conditions toward industrial application.

• Journal of the Korea Convergence Society
• /
• v.11 no.9
• /
• pp.109-115
• /
• 2020

With the continuous development of automobile design industry, fastback design style has become the main popular trend of automobile appearance design, and it has an important impact on the future automobile appearance design. This study summarizes the basic rules and characteristics of the design style base don combing, analyzing and verifying the data of the fastback design style. It provides the necessary basic research for the better application of the fastback design style in the future automobile design. Firstly, through the literature research method to sort out and analyze the de finition, origin and history of fastback design style. Secondly, through the comparative study, the author compares and analyzes the characteristics, advantages and disadvantages of the fastback design style and the step back design style. Thirdly, through case analysis, it studies the classification and characteristics of fastback design style. Finally, this paper summarizes the influence of the fastback design style on the future automobile appearance design, and the specific design methods. Forecasts the development trend of fastback design style in the field of automobile exterior design in the future. Through this research, we sorted out the related historical development of fastback design and the characteristics and advantages of fastback design style (from the perspective of functionality, economy and aesthetics).The fastback design style has formed a more systematic research theory, which provides basic research materials for future fastback design research. In the next stage, this study will be further subdivided, focusing on the different design features of different automobile manufacturers which subdivide the fastback design style into different design features according to their own needs.

• Journal of the Microelectronics and Packaging Society
• /
• v.19 no.2
• /
• pp.7-15
• /
• 2012

Semiconductor packages are increasingly moving toward miniaturization, lighter and multi-functions for mobile application, which requires highly integrated multi-stack package. To meet the industrial demand, the package and silicon chip become thinner, and ultra-thin packages will show serious reliability problems such as warpage, crack and other failures. These problems are mainly caused by the mismatch of various package materials and geometric dimensions. In this study we perform the numerical analysis of the warpage deformation and thermal stress of 4-layer stacked FBGA package after EMC molding and reflow process, respectively. After EMC molding and reflow process, the package exhibits the different warpage characteristics due to the temperature-dependent material properties. Key material properties which affect the warpage of package are investigated such as the elastic moduli and CTEs of EMC and PCB. It is found that CTE of EMC material is the dominant factor which controls the warpage. The results of RSM optimization of the material properties demonstrate that warpage can be reduced by $28{\mu}m$. As the silicon die becomes thinner, the maximum stress of each die is increased. In particular, the stress of the top die is substantially increased at the outer edge of the die. This stress concentration will lead to the failure of the package. Therefore, proper selection of package material and structural design are essential for the ultra-thin die packages.

• Journal of the Korean Institute of Gas
• /
• v.8 no.4 s.25
• /
• pp.62-69
• /
• 2004

It is necessary to eliminate the electric static for the prevention of disasters by electric static discharge, the improvement of production efficiency, the protection of a sensitive electronic devices in the variable manufacturing processes. Then it is handled for elimination of electric static in the painting plant, the film manufacturing plant, the producing semi-conductor factory. This study described on the ideal condition of electric static elimination efficiency by changing of the length of voltage input type eliminator's bar, the length of copper pipe and the gap of electrode and the existence of explosion by inflammable gas with that conditions. As the result, the electric static elimination efficiency has the most ideal value at the 8-11(mm) gap of the earth electrode and needle type electrode each elimination bar and there is not explode at the explosive experiment of inflammable gas with the ideal elimination bar. We can consider that there are some data which are needed for elimination efficiency and it will be able to protect the occurrence of explosion accident inflammable nas in the industrial fields.

• 대한공업교육학회지
• /
• v.44 no.2
• /
• pp.1-27
• /
• 2019

In recent years, space planning ability using 3D sketch software is required in the working field of interior design. However, vocational high school do not respond appropriately to changes in the industry, because the class of vocational high school consists of hands-on practical classes and 2D CAD based classes. There is a shortage of 3D sketch software-based instruction programs that can improve students' spatial planning skills. Therefore, this study is to develop instruction program using 3D sketch software for 'Planning for Residential Space' unit of NCS-based on interior design subject and to find out the effect on students' academic achievement by applying to vocational high school class. The 3d sketch software based instructional program developed in this study was developed through four stages of preparation, development, implementation and evaluation according to the PDIE model process. The experimental design model used nonequivalent group posttest-only design in this study. Experiments were conducted on vocational high school students in construction and 9 hours of interior design subjects were applied. After the experiments, students were tested for academic achievement in the cognitive, affective, and psychomotor areas. As a result, the instruction program using the 3d sketch program developed in this study was found to be more effective in improving students' academic achievement than existing manual instruction program in both cognitive, affective, and psychomotor areas.

• Journal of the Korea Institute of Information and Communication Engineering
• /
• v.13 no.3
• /
• pp.623-628
• /
• 2009

The emergence of compact and low-power wireless communication sensors and actuators in the technology supporting the ongoing miniaturization of processing and storage allows for entirely the new kinds of embedded systems. These systems are distributed and deployed in environments where they may have been designed into a particular control method, and are often very dynamic. Collection of devices can communicate to achieve a higher level of coordinated behavior. Wireless sensor nodes deposited in various places provide light, temperature, and activity measurements. Wireless sensor nodes attached to circuits or appliances sense the current or control the usage. Together they form a dynamic and multi-hop routing network connecting each node to more powerful networks and processing resources. Wireless sensor networks are a specific-application and therefore they have to involve both software and hardware. They also use protocols that relate to both applications and the wireless network. Wireless sensor networks are consumer devices supporting multimedia applications such as personal digital assistants, network computers, and mobile communication devices. Wireless sensor networks are becoming an important part of industrial and military applications. The characteristics of modem embedded systems are the capable of communicating adapting the different operating environments. In this paper, We designed and implemented sensor network system which shows through host PC sensing temperature and humidity data transmitted for wireless sensor nodes composed wireless temperature and humidity sensor and designs sensor nodes using embedded system with the intention of studying USN.

• Proceedings of the KAIS Fall Conference
• /
• 2000.10a
• /
• pp.30-33
• /
• 2000

최근 국내에서도 관 동맥 질환 환자의 수가 급증하고 있으며, 관 동맥 질환의 치료 방법인 관 동맥 성형 술은 관 동맥 stent의 도입에 의하여 보편화되어 국내에서 년간 5000개 이상의 stent가 시술되고 있다. 그러나 stent는 고가(1,200천원/개)로 전량 수입에 의존하고 있으며, 시술 후 사망까지 이를 수 있는 혈전에 의한 급성 페쇠와 재 협착이 문제점이다. 이를 위한 한가지 방법이 생체 적합성이 뛰어난 복합 stent의 개발인데 SiC나 Carbon을 coating한 stent는 시술 후 혈전 형성을 억제하는 것으로 알려져 있다. 특히 가장 순수한 Pyrolytic carbon은 hemocompatibility가 탁월하고 기밀 성이기 때문에 본 연구에서 그의 CVB-Kinetics를 연구코저 하는 것이다. methane으로부터 pyrolytic carbon의 CVD는 온도에 따라서 다양한 구조를 가지며 따라서 그의 mechanism도 다양하다는 것은 잘 알려져 있다. 더구나 광간(균질)반응과 표면(불균질)반응의 정량적 관계에 따라서도 다르다는 것도 확인되었다. 그러나 stainless steel 316L로 만든 stent는 12 - 15 %의 Ni과 2%의 Mo을 함유해서 금속성을 잃지 않는 저온(600℃)에서도 pyrolytic carbon의 속매적 CVD가 가능함을 그리고 SiC의 코팅에 적합한 buffer layer 역할을 함을 확인하였다. 그리하여 본 연구는 반응기 설계에 필요한 저온 촉매적 pyrolytic carbon의 CVD-kinetics의 연구결로 그의 mechanism과 함께 rate law 식을 유도, 확인하였으며 600℃, 90kPa에서 P/sub ch4//P/sub H2/=5:1과 체류시간 1.8 sec가 최적임을 발견하였다. 이때 석출속도 11.2 g-mol/g-cat.h 혹은 두께속도로 73 nm/sec를 나타내었다.메타놀-물 (1 : 1) 유출액에서 $(0.80\;{\mu}g)$ 검출되었다. 하면 morey eel내장에서 얻은 독물질도 DEAE-셀루로즈에서 ST-1 과 ST-2로 나누어지며, 이 ST-1의 TLC, HPLC 및 알루미나 컬럼상의 거동이 파랑비늘돔에서 얻은 ST-1의 그것과 같으므로 scaritoxin으로 보고한 ST-1은 ciguatoxin의 형태인 less polar cigutoxin (LPCTX) 으로 생각된다.에서 각각 대조구의 57, 413 및 315% 증진되었다. 거품의 열안정성은 15분 whipping시, pH 4.0(대조구, 30.2%) 및 5.0(대조구, 23.7%)에서 각각 $0{\sim}38.0$ 및 $0{\sim}57.0%$이었고 pH 7.0(대조구, 39.6%) 및 8.0(대조구, 43.6%)에서 각각 $0{\sim}59.4$ 및 $36.6{\sim}58.4%$이었으며 sodium alginate 첨가시가 가장 양호하였다. 전체적으로 보아 거품안정성이 높은 것은 열안정성도 높은 경향이며, 표면장력이 낮으면 거품형성능이 높아지고, 비점도가 높으면 거품안정성 및 열안정성이 높아지는 경향이 있었다.protocol.eractions between application agents that are developed using different languages. Dynamic agent invocation is accomplished by Java Native Interface(JNI) that links two heterogeneous methods, and by KQML language interface that facilitates the communications between heterogeneous agents. This scheme of dyna