• 한국결정성장학회지
• /
• 제21권4호
• /
• pp.164-168
• /
• 2011

고이온밀도 플라즈마 식각에 의한 고종횡비, 고이방성을 갖는 ZnO, $SnO_2$ 나노 구조 가스 감응층 형성을 위하여 mask 재료들과의 식각 선택도를 조사하였다. $25BCl_3$/10Ar ICP 플라즈마에서는 ZnO와 Ni 간 5.1~6.1 범위의 식각 선택도가 확보된 반면에 Al의 경우 효율적인 식각 선택도를 확보할 수 없었다. $25CF_4$/10Ar ICP 플라즈마에서는 ZnO와 Ni 간에 7~17 범위의 높은 식각 선택도를 얻을 수 있었다. $SnO_2$는 $SnF_x$ 식각 생성물의 높은 휘발성에 기인하여 Ni에 비해 매우 높은 식각 속도를 나타내었고, 최고치 약 67의 매우 높은 식각 선택도를 확보하였다.

• 대한전자공학회논문지SD
• /
• 제37권7호
• /
• pp.1-6
• /
• 2000

본 연구에서는 Pt 박막을 식각하기 이하여 기존에 최적화된 가스 혼합비인 $Cl_2$(10)Ar (90)에 $N_2$ 가스를 첨가하기 실험하였다. $Cl_2$(10)/Ar(90)의 가스 혼합비에 20% $N_2$가스 첨가시, $SiO_2$ 마스크에 대한 Pt 박막의 선택비 향상으로 70$^{\circ}$ 이상의 식각 프로파일을 얻을 수 있었다. 이는 $SiO_2$ 마스크 위에 Si-N, Si-O-N과 같은 차단막 생성을 통한 결과로 확인 되어졌다. $SiO_2$ 마스크에 대한 Pt 박막의 최대 선택비와 식각률은 각각 1.71과 4125 ${\AA}$/min 이다. 이는 Pt-N, Pt-N-Cl과 같은 휘발성 화합물의 생성을 통한 결과로 판단된다.

• 한국재료학회지
• /
• 제9권5호
• /
• pp.496-502
• /
• 1999

In this study, n-GaN samples were etched using planar inductively coupled $Cl_2$/$H_2$plasmas and the effects of plasma conditions on the etch properties, surface composition, and ohmic contact formation were investigated as a function of gas combination. As the addition of hydrogen to the $Cl_2$plasma increased to 100%, GaN etch rates decreased due to the reduction of chlorine radical density. Even though the variation of the surface composition is limited under $50\AA$, the surface composition was also changed from Ga-rich to N-rich with the increased addition of hydrogen to $Cl_2$. Etch products by the reaction between Ga in GaN and Cl in $Cl_2$ plasma were investigated using OES analysis during the GaN etching. The value of specific resistivity of the contact formed on the n-GaN etched using 100% $Cl_2$plasma was 3.1$\times$10\ulcorner$\Omega$$\textrm{cm}^2$, and which was lower than that formed on the non-etched n-GaN. However, the resistively was increased with the increased hydrogen percent in $Cl_2$/$H_2$.

• Journal of Radiation Protection and Research
• /
• 제12권1호
• /
• pp.48-53
• /
• 1987

중성자 선원의 강도를 측정하기 위하여 흔히 황산망간용액조 방법이 사용되고 있다. 본 연구에서는 $^{55}Mn(n,{\gamma})^{56}Mn$ 반응에 도입되는 국산 $MnSO_4{\cdot}H_2O$(동양화학제품)중에 불순들 성분을 규명하기 위하여 Ar-ICP 플라즈마방출 분광계측에 의한 분석화학 방법이 사용되었다. 분석결과로부터 주로 Co, Zn과 미량의 Cd, Li 등이 관련 불순물로서 중성자를 흡수하는 것으로 판명되었으며 전체 불순물에 의한 중성자 흡수 비율은 $^{55}Mn$에 의하여 포획되는 중성자 수의 약 1.37%로 산정되었다.

• 한국결정성장학회지
• /
• 제23권2호
• /
• pp.86-92
• /
• 2013

나노결정질 다이아몬드 박막 증착을 위한 전처리 공정으로 $SF_6/O_2$ 유도결합 플라즈마를 이용하여 Si 기판 표면을 texturing하였다. $SF_6/O_2$ 플라즈마 texturing은 2~16 범위의 매우 넓은 정규화된 표면 조도 선택성을 제공할 수 있음을 확인하였다. Texturing된 Si 기판 표면의 나노 다이아몬드 입자 seeding 이후 기존 기계적 연마 전처리에 비해 현저히 향상된 ${\sim}6.5{\times}10^{10}cm^{-2}$의 높은 핵형성 밀도를 확보하였다.

• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 2008년도 하계학술대회 논문집 Vol.9
• /
• pp.168-168
• /
• 2008

Dimension of a transistor has rapidly shrunk to increase the speed of device and to reduce the power consumption. However, it is accompanied with several problems like direct tunneling through the gate dioxide layer and low conductivity characteristic of poly-Si gate in nano-region. To cover these faults, study of new materials is urgently needed. Recently, high dielectric materials like $Al_2O_3$, $ZrO_2$, and $HfO_2$ are being studied for equivalent oxide thickness (EOT). However, poly-Si gate is not compatible with high-k materials for gate-insulator. Poly Si gate with high-k material has some problems such as gate depletion and dopant penetration problems. Therefore, new gate structure or materials that are compatible with high-k materials are also needed. TiN for metal/high-k gate stack is conductive enough to allow a good electrical connection and compatible with high-k materials. According to this trend, the study on dry etching of TiN for metal/high-k gate stack is needed. In this study, the investigations of the TiN etching characteristics were carried out using the inductively coupled $BCl_3$-based plasma system and adding $Cl_2$ gas. Dry etching of the TiN was studied by varying the etching parameters including $BCl_3$/Ar gas mixing ratio, RF power, DC-bias voltage to substrate, and $Cl_2$ gas addition. The plasmas were characterized by optical emission spectroscopy analysis. Scanning electron microscopy was used to investigate the etching profile.

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 2004년도 추계학술대회 논문집 전기물성,응용부문
• /
• pp.72-74
• /
• 2004

In this study, we used a inductively coupled plasma (ICP) source for etching $Al_2O_3$ thin films because of its high plasma density, low process pressure and easy control bias power. $Al_2O_3$ thin films were etched using $Cl_2/BCl_3$, $N_2/Cl_2/BCl_3$, and Ar/$Cl_2/BCl_3$ plasma. The experiments were carried out measuring the etch rates and the selectivities of $Al_2O_3$ to $SiO_2$ as a function of gas mixing ratio, rf power, and chamber pressure. When $Cl_2$ 50% was added to $Cl_2/BCl_3$ plasma, the etch rate of the $Al_2O_3$ films was 118 nm/min. We also investigated the effect of gas addition. In case of $N_2$ addition, the etch rate of the $Al_2O_3$ films decreased while $N_2$ was added into $Cl_2/BCl_3$ plasma. However, the etch rate increased slightly as Ar added into $Cl_2/BCl_3$ plasma, and then further increase of Ar decreased the etch rate. The maximum etch rate was 130 nm/min at Ar 20% in $Cl_2/BCl_3$ plasma, and the highest etch selectivity was 0.81 in $N_2$ 20% in $Cl_2/BCl_3$ plasma. And, we obtained the results that the etch rate increases as rf power increases and chamber pressure decreases. The characteristics of the plasmas were estimated using optical emission spectroscopy (OES).

• 한국표면공학회지
• /
• 제32권3호
• /
• pp.416-422
• /
• 1999

The characteristics of inductively coupled Cl$_2$/BCl$_3$ plasmas during the GaN etching were studied using plasma mass spectrometry by measuring the relative amounts of reactive ions, neutrals, and etch products. GaN etch rates increased with the increase of pressure and showed a maximum near 25mTorr for the pure $Cl_2$ and near 30mTorr for $Cl_2$$BCl_3$. The addition of$ BCl_3$ to $Cl_2$ also was increased GaN etch rates until 50%BCl$_3$ was mixed to $Cl_2$. The GaN etching with pure $Cl Cl_2$ appears to be related to the combination of Cl$_2^{+}$ ion bombardment and the chemical reaction of Cl radicals. In the case of the GaN etching with Cl$_2$/BCl$_3$, in addition to the combined effect of$_2^{ +}$ ions and Cl radicals, $_BCl2^{+ }$ ions appear to be responsible for some of GaN etching even though they do not have significant effect on the GaN etching compared to $Cl_2^{+}$ and Cl. $Ga^{+ }$ , $GaCl^{+}$ , $GaCl_2^{+}$ , and $N_2^{+}$ were observed as the positive ions of etch products, and the intensities of these etch products showed the same trends as those of GaN etch rate. Among the etch products, Ga and $N_2$ appear to be the main etch products.

• 분석과학
• /
• 제25권5호
• /
• pp.265-272
• /
• 2012

기존의 Okamoto cavity를 변형시킨 WR-340 도파관을 사용한 cavity를 제작하고 고출력(2.45 GHz, 2 kW)의 헬륨, 질소 및 아르곤 마이크로파 플라즈마(MIP; Microwave Induced Plasma)를 성공적으로 형성시켰다. 플라즈마 생성의 주요한 요인들은 내부전도체의 직경과 내부전도체와 외부전도체간의 간격, 내부전도체 끝과 토치의 위치 등이 있으며 그 중 헬륨 마이크로파 플라즈마에 대하여 cavity의 디자인을 최적화시키고 그 특성을 조사하였다. ICP(Inductively Coupled Plasma)용 mini 토치와 자체 제작한 나선형흐름토치를 비교 연구한 결과, 헬륨 플라즈마 기체 흐름량은 약 25 L/min~30 L/min로서 서로 비슷하였다. 토치 상단부에 석영관을 덧씌워 공기유입을 막은 결과, 340 nm 근처의 NH분자선들이 없어지거나 감소하였다. 플라즈마의 온도 및 전자밀도를 측정한 결과, 4,350 K의 들뜸 온도와 $3.67{\times}10^{11}/cm^3$의 전자밀도를 얻었다. 이 값들은 기존의 다른 마이크로파 플라즈마와 비슷하거나 약간 작은 값이다. 고출력의 플라즈마로서 수용액을 직접 분석하는 것이 가능하였고 현재 Cl의 검출한계는 116 mg/L 수준으로서 아직 분석적인 최적화가 필요한 단계이다.

• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 2008년도 추계학술대회 논문집 Vol.21
• /
• pp.363-363
• /
• 2008

The development of dry etching process for sapphire wafer with plasma has been key issues for the opto-electric devices. The challenges are increasing control and obtaining low plasma induced-damage because an unwanted scattering of radiation is caused by the spatial disorder of pattern and variation of surface roughness. The plasma-induced damages during plasma etching process can be classified as impurity contamination of residual etch products or bonding disruption in lattice due to charged particle bombardment. Therefor, fine pattern technology with low damaged etching process and high etch rate are urgently needed. Until now, there are a lot of reports on the etching of sapphire wafer with using $Cl_2$/Ar, $BCl_3$/Ar, HBr/Ar and so on [1]. However, the etch behavior of sapphire wafer have investigated with variation of only one parameter while other parameters are fixed. In this study, we investigated the effect of pressure and other parameters on the etch rate and the selectivity. We selected $BCl_3$ as an etch ant because $BCl_3$ plasmas are widely used in etching process of oxide materials. In plasma, the $BCl_3$ molecule can be dissociated into B radical, $B^+$ ion, Cl radical and $Cl^+$ ion. However, the $BCl_3$ molecule can be dissociated into B radical or $B^+$ ion easier than Cl radical or $Cl^+$ ion. First, we evaluated the etch behaviors of sapphire wafer in $BCl_3$/additive gases (Ar, $N_2,Cl_2$) gases. The behavior of etch rate of sapphire substrate was monitored as a function of additive gas ratio to $BCl_3$ based plasma, total flow rate, r.f. power, d.c. bias under different pressures of 5 mTorr, 10 mTorr, 20 mTorr and 30 mTorr. The etch rates of sapphire wafer, $SiO_2$ and PR were measured with using alpha step surface profiler. In order to understand the changes of radicals, volume density of Cl, B radical and BCl molecule were investigated with optical emission spectroscopy (OES). The chemical states of $Al_2O_3$ thin films were studied with energy dispersive X-ray (EDX) and depth profile anlysis of auger electron spectroscopy (AES). The enhancement of sapphire substrate can be explained by the reactive ion etching mechanism with the competition of the formation of volatile $AlCl_3$, $Al_2Cl_6$ or $BOCl_3$ and the sputter effect by energetic ions.