• Proceedings of the KIEE Conference
• /
• 1998.07c
• /
• pp.1159-1162
• /
• 1998

The induced voltage of underground pipelines caused by the stray current not only do harm to workers and instruments. but also cause big accident such as gas explosion. The AC stray current is mainly produced by the grounding system of the 22.9kV distribution power system and the DC stray current is mainly produced by the subway system. The mechanism of AC and DC induction, stray current failure examples of domestic and foreign countries and the countermeasure of the AC and DC induction are described.

• Proceedings of the KIEE Conference
• /
• 2000.07d
• /
• pp.2374-2376
• /
• 2000

In this paper, we propose an indirect vector control method using Adaptive Neuro-Fuzzy Inference System (ANFIS) parameter estimator. It estimates the rotor time constant when the indirect vector control of induction motor is applied. We use the stator current error that is difference between the current command and estimated current calculated from terminal voltage and current. And two induced current estimate equations are used in training ANFIS.The estimator is trained by the hybrid learning algorithm. Simulation results shows good performance under load disturbance and motor parameter variations.

• The Transactions of the Korean Institute of Electrical Engineers C
• /
• v.52 no.12
• /
• pp.573-578
• /
• 2003

In this study, new type of induction charging system for electrostatic spraying was manufactured and proposed to improve the electrical safety and charging efficiency. And parameters of proposed system to generate the maximum deposition current with electrical safety were selected and investigated. The selected parameters were frequency of square pulse and thickness of insulation material, outer diameter of device and thickness and positions of electrode. Charging quantity of water drop was measured by deposition current detected from sensing plate indirectly. The maximum deposition current for each parameter were 3.5[uA] at the frequency of 15[kHz] and thickness of 0.25[mm] insulating layer. And maximum deposition currents were 2.8[uA] and 3.0[uA] at 25[mm] outer diameter of charging device and 0.25[mm] thickness of electrode each. Effects of electrode position from spraying nozzle on deposition current was a little.

• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 2005.11a
• /
• pp.400-405
• /
• 2005

The diagnosis of mechanical load and of power transmission system failures is usually carried out through mechanical signals such as vibration signals, acoustic emissions, motor speed envelope. If the mechanical load comes from an electrical machine the mechanical failures could be detected previously. Mechanical rotor imbalances and rotor eccentricities are reflected in electric, electromagnetic and mechanical quantities. Therefore, many surveillance schemes apply to the Fourier spectrum of a line current in order to monitor the motor condition. Due to the interaction of the currents and voltages, both these current harmonics are also reflected by a single harmonic component in the frequency spectrum of the electric power. Motor Current Signature Analysis is the usuful technique to assess machine electrical condition.

• Proceedings of the KIPE Conference
• /
• 2000.07a
• /
• pp.195-198
• /
• 2000

In this paper the insulation characteristics test results of 25 low-voltage induction motors($3\phi$, 5HP, 380V) are presented. Five different types of insulation techniques are applied to 25 motors. The maximum partial discharge (PD) magnitude ($\textrm{Q}_{m}$) discharge inception voltage (DIV) dissipation factor tip-up ($\Delta$tan$\delta$) and rate of change in AC current($\Delta$I) are measured by PD and AC current tests. Also the insulation breakdown tests by high voltage pulse are performed and the corresponding breakdown voltage are obtained.

• The Transactions of the Korean Institute of Electrical Engineers B
• /
• v.52 no.2
• /
• pp.87-92
• /
• 2003

This paper presents a flux estimator for the sensorless vector control of induction motors. The proposed method utilize the combination of the voltage model based on stator equivalent model and the current model based on rotor equivalent model, which enables stable estimation of rotor flux in high speed region and in low speed region. The dynamic performance of proposed method is verified through the experiment. The experimental results show that motors ran easily start even under 150[%] load condition and operate continuously below 0.5[Hz].

• 한국정보디스플레이학회:학술대회논문집
• /
• 2009.10a
• /
• pp.307-309
• /
• 2009

We have fabricated vertical-type organic transistors (static induction transistors; SITs) with built-in nano-triode arrays formed in parallel by a colloidal-lithography technique. Using this technique, we could fabricate a microstructure in a lateral direction within a large-scale organic device without relying on photolithography. The organic transistor showed low operating voltages, high current output, and large transconductance.

• The Transactions of the Korean Institute of Electrical Engineers
• /
• v.34 no.7
• /
• pp.283-288
• /
• 1985

This paper is concerned with the analysis of microprocessor-based PID control for the current source inverter-induction motor derive system. A linearized dynamic model of the motor is derived and is converted into the discrete-time model. With the equation, the overall system including the feedback loops is formulated into a single discrete-time state equation. The stability regions are determined at various values of controller gains. The transient responses of the motor speed are simulated by digital computer and are verified by laboratory experiments.

• Proceedings of the Korean Institute of IIIuminating and Electrical Installation Engineers Conference
• /
• 2006.05a
• /
• pp.91-96
• /
• 2006

This paper shows quantatively the cause of electric power induction that was occured by flowing current when high speed electric car travels and the investigation of earth potential upswing and animal damage example by rail leakage current.

• Proceedings of the KIEE Conference
• /
• 2002.07b
• /
• pp.848-850
• /
• 2002

Single phase induction motor is directly used usual source, it can be a source of an appliance such as mechanical fan, refrigerator, washing machine, etc. Especially capacitor-run single phase induction motor is suitable to make more inexpensive and high efficient products because it is more high efficiency, and good to start than other single phase induction motors. Generally, voltage and current of capacitor-run single phase induction motor transfer to the part of positive phase and negative phase based on two motor theory. In this paper, we simulate the torque characteristics to capacitance variation from single phase induction motor's equivalent circuit. Through the test using the real motor, we compare and investigate the maximum torque of run state related with capacitance and the adequacy of the converted model.