• 한국멀티미디어학회논문지
• /
• 제10권2호
• /
• pp.187-199
• /
• 2007

회화적 렌더링의 궁극적인 목적은 주어진 영상을 가지고 사람이 직접 그린 듯 한 회화적 느낌을 표현하는 것이다. 이러한 회화적 느낌을 표현하기 위한 요소에는 브러시의 굵기, 방향, 질감, 그리고 생성된 브러시가 캔버스에 그려질 것인가를 판단하는 기준설정 등이 있다. 본 논문에서는 에지 밀도를 이용해 브러시가 캔버스에 그려질 것인가를 판단하는 기준을 설정하는 알고리즘을 제시한다. 에지밀도란 일정 영역에서의 에지의 양을 나타낸다. 이와 함께 정적 격자 단위로 그려질 위치를 찾는 것이 아닌 동적 격자단위로 찾아가는 방법을 사용하고 브러시의 일관된 방향성을 위해 방향 보간을 한다. 또한 텍스처를 가진 다양한 브러시를 사용하여 질감을 표현한다. 에지의 밀도정보를 이용한 그려질 판단 기준설정, 통적 격자에 의한 위치선정, 일관된 브러시의 방향, 그리고 텍스처를 사용한 질감 표현 과정들을 통해 더 사실적인 오일 페인팅(oil painting)의 효과를 얻을 수 있다.

• 대한치과보철학회지
• /
• 제40권3호
• /
• pp.236-245
• /
• 2002

The acrylic resin was first introduced as denture base materials in 1937 and it is commonly used for denture base fabrication nowadays. Three different curing cycles (Conventional curing cycle, short curing cycle and long curing cycle) and three commercially available heat-activated acrylic resins (Vertex RS, Lucitone 199 and ProBase Hot) were investigated to find the curing cycle and material that showed the minimum shrinkage of the resin during polymerization process. A brass master mold was fabricated and duplicated by additional silicone impression material. Stone molds were made by pouring of type III dental stone (SILKY-ROCK YELLOW, Whip-Mix, Louisville, Kentucky). It was embedded in the flask. Strain gauge and thermocouple were embedded in the specimen. Strain gauge and thermocouple were connected to signal conditioning amplifier and data was recorded by pre-programmed software. The parameters ESmax (Maximum expansion strain), Sb (Strain measured just before deflasking procedure), Sa (Strain measured just after deflasking procedure) and Sf (Strain measured at the end of the experiment) were measured. ${\Delta}$S was calculated from Sb and Sa (${\Delta}$S=Sb-Sa). In the experiment concerned about materials, the parameters 90-ESmax (Maximum expansion strain measured during early 90 minutes of curing procedure), 180-ESmax (Maximum expansion strain measured from 90 minutes to 180 minutes), Sb, Sa, ${\Delta}$S and Sf were measured and the following conclusions were made. 1. The ESmax value of conventional curing cycle showed the largest value and the 180-ESmax value of Lucitone 199 showed the smallest value. 90-ESmax values showed no significant difference (p<0.05). 2. ${\Delta}$S values of conventional curing cycle showed the positive values. ${\Delta}$S values of short curing cycle and long curing cycle showed the negative values. All three materials cured by conventional curing cycle showed the positive values. 3. The Sf values of long curing cycle and ProBase Hot (cured by conventional curing cycle) showed the smallest values.

• The Journal of Advanced Prosthodontics
• /
• 제2권3호
• /
• pp.102-105
• /
• 2010

PURPOSE. The aims of this study were to suggest a method of fabrication of the record base using a light-polymerized resin by applying the two-phase fabrication method for the improvement of the fit of the record base and to compare the degree of fit according to the separation site. MATERIALS AND METHODS. In the edentulous cast of maxilla, four test groups were considered. In the first, second, third, and fourth test groups (n = 12 in each group) the separation was done at 0, 5, 10, and 15 mm, respectively below the alveolar crest along the palatal plane. For the control group, the record base was made without separating the two sections. The light-body silicone material was injected into the fitting surface of the record base. It was then placed onto the cast and finger pressure was applied to stabilize it in a seated position followed by immediate placement onto the universal test device. Finally, the mass of the impression material was measured after it was removed. ANOVA was performed using the SAS program. For the post-hoc test, the Wilcoxon Rank-Sum test and the Tukey-Kramer HSD test were performed ($\alpha$ = 0.05). RESULTS. The control group and Group 3, 4 showed significant differences. The Group 3 and 4 showed significantly smaller inside gaps than the control group which was not made with the two-phase fabrication method. CONCLUSION. The two-stage polymerized technique can improve the fit of the denture base particularly when the separation was made at 10 to 15 mm from the alveolar crest.

• 한국산학기술학회논문지
• /
• 제11권1호
• /
• pp.49-54
• /
• 2010

자동차의 A.C 제너레이터(alternating current generator) 부품으로 사용되는 로터폴(rotor pole)을 가공할 때는 트랜스퍼온간단조금형(transfer warm forging die)으로 성형한다. 소재를 온간가공 영역으로 가열한 후 즉시 금형안으로 이송시켜 제1스테이지(1st stage)에서 업세팅가공(upsetting work)하고 제2스테이지(2nd stage)로 이송하여 측방압출(lateral extrusion)가공을 한다. 이때 측방압출 스테이지의 금형에서 다이블록(die block), 다이부싱(die bushing), 센터펀치(center punch), 사이드펀치(side punch)의 접촉면이 압출시의 과혹(過酷)한 조건에 견디지 못하여 쉽게 마멸(abrasion)되어 금형수명(die life)을 단축시키고 있다. 이 때문에 생산량 감소로 인한 납기지연, 금형의 수리보수시간 과다, 제품의 정밀도 저하 등의 문제점이 발생되고 있다. 이러한 문제점을 해결하기 위하여 금형재질 선정과 열처리 작업 싸이클 개선, 방전가공시의 트러블 해소, 핵심부품의 구조변경 등을 연구하여 금형수명을 40~50% 연장 하고자 하였다.

• 복식
• /
• 제43권
• /
• pp.259-282
• /
• 1999

To analyze the characteristics of Orientalism which is expressed in the fashion of the 1990's this study was examined according to three aspects such as form textiles and pattern and the aspects was considered with regard to Chinese Indian Japanese Korean, Southeas Asian and North African style. 1. In form Orientalism which is influenced by latest other fashion trend; Naturalism and Minimalism is expressed as a comfortable casual style which simplifies the way of wearing and mixes the characteristic elements of folk costume with western costume. The way of layerd wearing like knotting wrapping draping and the symbolic from which is inspired by the unique are of each country are shown. 2. In textiles Chinese Japanese and Indian silk as well as Southeast Asian and North African cotton show a splendid oriental impression using vivid color. On the other hand the linens of Korea like hemp and ramie emphasize natural characteristics and show a simple and unartificial oriental beauty. But in the use of material and color it shows a remarkable tendency to break the preconceived idea by coordinating a luxurious silk with a practical denim or harmonizing technical new-masterials with traditional materials. 3. In pattern the decorative elements of Orientalism such as a traditional pattern skills to dye embroidery and other decorations are emphasized on the form of western costume. The sketchy patterns of Chinese Korean and Japanese styles which include the pattern of a flower a bamboo and a butterfly are expressed using embroidery or textile printing. The geometrical seriate patterns of Southeast Asian and North African styles use traditional dyeing methods like Batik. Also the Indian technique of decoration like Mirro Work satisfies handcrafted royalty and feminine romantic taste in modern minimal fashion. The Orientalism expressed in the fashion of 1990's emphasizes the characteristics of people wearing colthing which break the preconceived idea by simplifying the form harmonizing differences between oriental and western cultures and mixing the elements of traditional costumes among countries. Most of all. Ethno using geonmetrical seriate pattern and technical new metal material and Romantic Ethnic using flower embroidery precious stones and beads are appearing as a distinctinve feature.

• 한국의류산업학회지
• /
• 제8권3호
• /
• pp.258-268
• /
• 2006

The purpose of this study is to consider incense culture found in costume and life in forms of carrying and decoration. Here, incense for carrying and decoration is classified into two cases, using it as a costume accessory and life space. Hyangjumony, Hyangnorigae, Hyangjul, Hyangdae and Hyangseonchu were costume accessories. Hyangjumony was not only used for the royal palanguin, but also for bedroom. When Poetic Literature, and other ancient publications were reviewed in regard to incense for carrying and decoration, it was estimated that incense began to be carried for the first time before the late period of Shilla(9C). In addition, it was found that incense was not just a personal taste, but one of important gifts exchanged between states, envoys of different nations and between sovereign and subject and that incense was a necessary costume accessory for men. Types of incense for carrying and decoration used in this nation are classified into Hyangjumony, Hyangnorigae, Hyangjul and Hyangseonchu. Hyangjumony is a fabric pouch that contains incense. Hyangnorigae is Norigae whose main material is incense. Hyangjul is a string to which incense is hanged. Hyangseonchu is Seonchu whose main material is incense. Incense for carrying and decoration was based on five colors that symbolize cosmic order and harmony, of which red and purple were mostly used. Red strongly suggests expelling Yin with Yang, or exorcism. The color gives a strong impression, so it was often used to make a carried incense more decorating. Main materials of incense for carrying and decoration were gold, silver, precious stone and horsehair. They are different in characteristics, but were used appropriately for incense fragrance and decoration. Patterns mainly used for the incense had shapes of animal, plant, sipjangsaeng and letter. These were all auspicious patterns that symbolize human wishes and desires, especially individual and family happiness.

• 대한치과보철학회지
• /
• 제31권2호
• /
• pp.219-235
• /
• 1993

To determine the compatibilities of soft liming materials with denture cleansers by measuring the flexibility and elasticity and investigating the surface changes, 4 self-curing acrylic resin soft lining materials and 1 heat-curing silicone soft lining material were evaluated. 3mm thick x 20mm diameter discs of soft lining materials were individually bonded to a hard acrylic resin base as per manufacturers’instructions. Using an Instron universal testing machine, a static stress of $2kg/cm^2$ was applied for 30secs., the strain in compression was measured, giving an indication of the material’s flexibility. Elastic recovery was measured at 10secs. After removal of stress. Surface changes were investigated with Stereomicroscope. Then the specimens were immersed in 4alkaline peroxide denture cleansers and water as control group, tests were carried out at 1 day, 2 days, 7 days, 14 days and 30 days. The results were as follows : 1. Alkaline peroxide denture cleansers caused considerable porosity on the surface of selfcuring acrylic resin soft lining materials, and the most affected by the cleansers were Viscogel, Coe-Soft, Coe-Comfort, Lynal, in that order. 2. There was significant difference in flexibility between each soft lining material except for Coe-Comfort and Visco-gel, and every soft lining material was significant difference in elasticity. Especially Molloplast-B and Lynal were less flexible and more elastic than other soft lining materials(p<0.05). 3. The denture cleansers increased the flexibility and elasticity of the soft lining materials compared with control group(p<0.05), and Denalan, Polident, Kleenite, Efferdent affected the soft lining materials in that order. 4. There was significant difference in flexibility between each denture cleanser except for Denalan and Polident(p<0.05). Though Denalan and Polident, Denalan and Kleenite did not show significant difference in elasticity, other denture cleansers showed significant difference among each other(p<0.05). 5. Clinically Coe-Comfort, Coe-Soft and Visco-gel were incompatible with alkaline peroxide denture cleansers, and Lynal would be used within only 2 weeks. But Molloplast-B was compatible with alkaline peroxide denture cleansers.

• 디자인학연구
• /
• 제16권1호
• /
• pp.63-72
• /
• 2003

본 연구의 목적은 도시민의 일상체험의 장인 가로공간을 대상으로 대상지역 가로경관의 역사적, 문화적 특성을 제고한 상징 이미지를 추출하고 이것을 바탕으로 한 지역의 정체성을 명확히 하는데 있다. 이를 통해 지역 이미지의 상징성과 미래지향적 가로의 이미지를 가로환경시설물에 적용함으로써 지역의 상징성을 표현하고 개성 있는 거리로 새롭게 인식시켜 활력 있는 가로환경을 조성하고자 한다. 또한 이 연구를 통해 상징가로 환경조성의 기초자료를 제시하고 실제적인 디자인 사례를 제시함으로써 특성화된 지역문화를 활성화하는데도 그 목적 이 있다. 상징가로의 디자인 접근방법으로 역사적 요소가 상실되고 도시화(신도시)가 이루어진 가로를 대상으로 지역의 상징적 이미지를 현재의 지역이미지와 미래지향적 이미지로 추출하였다. 이미지 평가실험을 통해 추출된 상징적 이미지를 바탕으로 미래지향적인 가로의 상징도구로 가로환경시설물을 이용하여 지역의 가로를 특성화하였다. 가로환경시설물의 디자인에 상징이미지를 적용하여 타 지역과 차별화된 가로를 형성하고 지역의 아이덴티티(Identity)를 확립함으로써 지역민의 소속감, 자부심과 애향심을 심어주는데 도움을 주고, 공공기관에서 지금까지의 연구내용과 연관된 계획을 수립하고 시행하고자 할 때, 본 연구가 상징성 추출에 있어서 하나의 방향성을 제시하였음에 그 의의를 둔다.

• 대한치과보철학회지
• /
• 제45권5호
• /
• pp.653-664
• /
• 2007

Statement of problem: The screw detorque value is a measure of the preload remaining in the screw just before detorquing. Purpose: This study evaluated the effect of different screw tightening sequences and tightening methods on detorque values for a well-fitting implant superstructure. Material and method: An implant superstructure that connected directly to four implants (Astra Tech) was fabricated on a fully edentulous mandibular acrylic resin model. Six well-fitting dental stone casts were made with a pickup impression of the superstructure from the acrylic resin model. To evaluate the effect of three screw tightening sequences (1-2-3-4, 2-4-3-1, and 2-3-1-4) and two tightening methods (2-step and 1-step) on the stability of screw joint, the detorque values for a well-fitting implant superstructure were measured twice after screw tightening using 20 Ncm. Detorque values were analyzed using multi-way analysis of variance and two-way analysis of variance at a .05 level of significance. Results: 1. The mean detorque values for three screw tightening sequences were 12.3 Ncm, 12.6 Ncm, and 12.0 Ncm, respectively. 2. The mean detorque values for two screw tightening methods were 12.0 Ncm, and 12.2 Ncm, respectively. 3. The mean of mimimum detorque values for three screw tightening sequences and for two tightening methods were 10.6 Ncm, 11.1 Ncm, 10.5 Ncm, and 9.8 Ncm, respectively. 4. No statistically significant differences among the variables of screw tightening sequence and tightening method were found (p>.05) for detorque values and for mimimum detorque values. Conclusion: Within the limitations of this study, the screw tightening sequence and tightening method did not have a significant effect on the detorque values for a well-fitting implant superstructure.

• 구강회복응용과학지
• /
• 제38권1호
• /
• pp.34-41
• /
• 2022

최근 디지털 기술과 Computer-aided design/Computer-aided manufacturing (CAD/CAM) 작업 환경은 의치 제작에 있어 임상의의 진료 과정의 변화를 가져왔다. CAD/CAM 기술을 이용한 의치 제작 방식은 진료 및 기공 과정을 단순화하여 오류의 발생을 감소시키며, 임상적인 효율성과 편리함을 제공한다. 본 증례는 하악 편위를 가진 상·하악 완전 무치악 환자에서 광경화 SLA 기반의 3D 프린팅을 이용한 디지털 제작 방식의 양악 총의치 수복 증례이다. 구강 스캐너로 채득한 디지털 모형에서 기록상을 제작하였고 교합제에 악간관계를 기록한 후 부가 중합형 실리콘 인상재로 폐구 정밀 인상을 채득하였다. 또한 교합제를 장착하고 촬영한 안면 스캔 데이터를 추가로 획득하여 기공 작업 시 교합 평면 결정이나 인공치 배열에 참고할 수 있도록 하였다. 인상체를 3차원 스캔 후 CAD 프로그램을 통해 인공치를 배열하였고, 연마면을 형성하여 의치 디자인을 완성하였다. 시적 의치 및 최종 의치는 미국식품의약국(Food and Drug Administraion, FDA) 승인을 받은 액체 광경화성 레진을 이용하여 stereolithography (SLA) 기반 3D 프린터로 출력하였고, 최종 의치는 적절한 안정과 유지, 지지를 보였으며 기능적, 심미적으로 만족스러운 결과를 얻을 수 있었다.