• Journal of the Korea Institute of Information and Communication Engineering
• /
• v.14 no.11
• /
• pp.2397-2402
• /
• 2010

Dielectric resonator bandpass filters with various time-delay at 800MHz were designed and fabricated in this paper. from the results of this study. first of all, good response. characteristics were measured for all cases. The insertion loss was below 2dB and flatness for ripple was below 0.2dB, whereas return loss was over 20dB, respectively. The measured delay time of the fabricated prototype were 6ns, 12ns and 200s, respectively and the flatness characteristics did not exceeding Ins for all cases. Furthermore, 2~4ns of flatness were measured for 2-hole dielectric block and other dielectric resonator filters with various delay time by combination of each prototypes filters were also implemented.

• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.16 no.11
• /
• pp.1054-1062
• /
• 1991

In this paper a communication system using direct sequence spread spectrum (DS/SS) technique is constructed to transmit burst format data over power line channel with impulsive noise and narrowband interferences. Fast code synchronization is acquired by digital matched filter and data decision is accomplished by sampling pulses. In order to examine the performance of the power line communication system, but error rate and packet loss rate are measured over the simulation channel with various noise sources. When the packet composed of 1-bit preamble and 63-bit data is transmitted under very high burst impulsive noise, the bit error rate is about 10$^3$-10$^4$ and the packet loss rate is below 0.07.

• The Transactions of The Korean Institute of Electrical Engineers
• /
• v.59 no.8
• /
• pp.1394-1400
• /
• 2010

This paper introduces a newly improved Ultra-FRFET that has much better reverse recovery characteristic than that of the typical MOSFET and presents its effectiveness in the HV-BLU system of LCD TVs. The reverse recovery time, $T_{rr}$ of Ultra-FRFET is shorter than 40nsec and the peak value of reverse current, $i_{rr}$ is also much smaller compared to the typical MOSFET's, which are sufficient to prevent the MOSFET’s failures without additional FRDs and diodes in HV-BLU system with a half-bridge resonant inverter topology worked by PWM method. In order to verify the validity, the loss analysis and the implementation results in cases when both the conventional solution using typical MOSFETs with additional FRDs and a new solution using Ultra-FRFETs are applied to a HV-BLU of 40" LCD TV are presented. As a result, the effectiveness of Ultra-FRFET was verified and the results are presented in this paper.

• Journal of the Korean Institute of Illuminating and Electrical Installation Engineers
• /
• v.27 no.10
• /
• pp.15-20
• /
• 2013

In this paper, wireless power transfer system using the magnetic resonance was designed and applied to LED lighting for implementation of wireless lighting. This lighting was made by the converted DC driving type and the direct AC driving type. In the former, transferred AC power was rectified into DC and regulated to the specified voltage value, which leads to produce the loss at the rectifying and regulating circuit. In the latter, wireless-transferred AC power was directly applied to LED, which get rid of the loss derived from the additional circuit. For the efficiency-comparison between the former and the latter, the power at each stage was measured when the same optical output radiated from LED lighting part. The result revealed that the direct AC driving type had 18% higher efficiency than the DC driving type and confirmed that LED lighting using magnetic resonance wireless power transfer system can be efficient by direct AC power supply. And the direct AC driving type had the simple circuit structure and the simple LED lighting formation, so this can leads to various application.

• Journal of Power Electronics
• /
• v.18 no.2
• /
• pp.332-342
• /
• 2018

This paper proposes a parameter design method for multi-element resonant converters (MERCs) with a unique resonant zero point (RZP). This method is mainly composed of four steps. These steps include program filtration, loss comparison, 3D figure fine-tuning and priority compromise. It features easy implementation, effectiveness and universal applicability for almost all of the existing RZP-MERCs. Meanwhile, other design methods are always exclusive for a specific topology. In addition, a novel dual-CTL converter is also proposed here. It belongs to the RZP-MERC family and is designed in detail to explain the process of parameter selection. The performance of the proposed method is verified experimentally on a 500W prototype. The obtained results indicate that with the selected parameters, an extensive dc voltage gain is obtained. It also possesses over-current protection and minimal switching loss. The designed converter achieves high efficiencies among wide load ranges, and the peak efficiency reaches 96.9%.

• Journal of the Korean Society for Railway
• /
• v.11 no.1
• /
• pp.69-74
• /
• 2008

This paper presents the design and implementation of MIB for SNMP-based PLC system which is applicable to communication for railway vehicles. The proposed MIB has four nodes which are "Basic Information", "Configuration", "Stats", and "Alarm." The essential peripheral functions for "Alarm" to improve the performance of PLC are deyised. ACF is for auto connecting devices without intervention of the user. DEC is for checking the loss of data and the presence of error. DLPF is for preventing the loss of data and error To evaluate the proposed system, the experimental set-up is developed and the experiments are successfully carried out. The conclusion points out that the suggested MIB contributes the betterment of the conventional PLC systems.

• Journal of The Korean Digital Architecture Interior Association
• /
• v.9 no.3
• /
• pp.69-76
• /
• 2009

The importance of efficient construction site management has been growing as the amount of construction information increases which is used in the growing construction site. Accordingly in this study, we are trying to find out the application situation and possibility of BIM through theoretical examination and domestic & overseas case study of BIM and we are trying to suggest the way of efficient construction site management formulation through implementation phase-oriented and cooperation entity-oriented analysis in the construction site. We found out that it was possible to minimize time loss and financial loss by visualizing 2D drawings through 3D modeling of target building by applying BIM and that it was possible to improve accuracy of budget planning with quantitative information of 3D model, to plan construction process with more confidence due to accurate architectural information of drawings and quantitative information, and to manage cost and quality through process management based on construction information acquired by BIM including object information by part. It is concluded that we can improve efficiency of construction management between field and each cooperating entity by integrating and linking BIM information through this process.

• The Transactions of the Korean Institute of Electrical Engineers C
• /
• v.54 no.5
• /
• pp.185-189
• /
• 2005

This paper focuses on the design for Rx/Tx switch module of GSM(global standard mobile) band, characterization of a miniature, low power and dual-band implementation of the front-end switch module with low-pass filer And the effort to make agreement between the simulated design and the measured data for these solutions takes the place through accumulated design and manufacturing data library. We present the design, modeling and measurement of switch module integrating GSM Rx/Tx switching circuit and LPF(low pass filter) on a LTCC(low temperature co-fired ceramic) substrate. For GSM application, insertion and return loss of the low pass filter designed was less than 0.3 dB which was less than 12.7 dB at 900 MHz. The LTCC switch module contained 10 embedded passives and 3 surface mount components integrated on 4.6$\times$4.8$\times$1.2 mm, 6-layer multi-layer integrated circuit. The insertion loss of switch module measured at 900 MHz was 11 dB. In both of the design approach yielded excellent agreement between measured and simulated results.

• Proceedings of the KIEE Conference
• /
• 2001.11c
• /
• pp.68-71
• /
• 2001

This paper has been studied for a comparison of the propagation and noise characteristics between ultrasonic and electromagnetic wave for the high speed communication of the short range telemetry. We analyze the propagation depth of electromagnetic and ultrasonic wave by skin depth effect and by ultrasonic loss ratio. We also studied several effects such as near field effect in electromagnetic wave and Rayleigh scattering noise of ultrasonic wave, etc. We show the experimental results of their propagation loss and modulation experiments in water. The experimental results show that both method is good for the implementation of short range telemetry.

• Journal of the Institute of Electronics Engineers of Korea TC
• /
• v.48 no.1
• /
• pp.97-101
• /
• 2011

Quad band p-HEMT SP6T switch for handset applications was developed. To achieve the low insertion loss and high isolation, trade-off between "On" state and "Off" state was considered by optimization of unit cell. Especially, in case isolation between transmit port and receive port, it was achieved by large capacitors and miniaturization of chip size was achieved by common voltage control and ground using back via process. Designed SP6T switch has size of $950um{\times}100um$ and take into consideration the gate recess error, excellent loss and isolation was confirmed in operating frequency.