• Fire Science and Engineering
• /
• v.24 no.3
• /
• pp.52-57
• /
• 2010

Fire protection countermeasure were considered on the straw thatched roof and wooden structure. For the fire resistant treatment, rice straw was soaked in the fire resistant liquid with different soaking time. After treatment, some rice straw sample was washed with water then the rice straws were tested to check the fire resistance performance. And the wood was soaked in the fire resistant liquid at an atmospheric pressure, vacuum-pressure condition and painted with brush on the surface. To analyse the fire resistant performance of rice straw, ignition delay time was measured under the radiant heat flux of cone heater. And the fire resistant performance of wood samples were tested with 45 degree fire resistant test apparatus and cone heater. Based on the cone heater test, the rice straw which most easily ignitable material shows the longer ignition delay time than not treated ones and even in the water washed straw show a longer ignition delay time than not treated ones. And fire resistant treated woods of vacuum-pressure treated sample showed the most excellent performance on fire resistance. And the fire resistant treated by brush and soaking showed a longer ignition delay time than not treated ones. From this experiment, it was found that a fire resistant treatment of rice straw and wood of the house can be protected from the fire spread.

• Journal of the Society of Disaster Information
• /
• v.18 no.3
• /
• pp.574-580
• /
• 2022

Purpose: As corn oil is semi-drying oil, it has more double bonds than non-drying oil and is easier to combine with oxygen. In addition, among the causes of spontaneous ignition, accidents caused by oil-soaked cloths due to oxidative heat are gradually increasing. Therefore, the purpose of this study is to understand the characteristics of spontaneous combustion according to the number of towels and the amount of corn oil at 65℃. Method: After setting the test temperature to 65℃, 25ml, 50ml, 75ml of corn oil per towel was sprayed. The central temperature of the sample rises above the set temperature. It was determined, and when the central temperature of the sample became similar to the set temperature, it was determined as non-igniting. Result: After evenly distributing 25ml of corn oil per towel, as a result of the experiment, 5 towels did not ignite, and 10 and 15 towels ignited. Also, as a result of an experiment using 50ml and 75ml of corn oil per towel, spontaneous ignition occurred when the number of towels was 5, 10, or 15 sheets. Conclusion: Even a small amount can cause a fire if the conditions for spontaneous ignition are met.

• Journal of the Korean Society for Aeronautical & Space Sciences
• /
• v.32 no.10
• /
• pp.102-111
• /
• 2004

The procedure of design and manufacture of sub-scale combustor using bipropellant swirl injector with external mixing for a liquid rocket engine are described. The results of cold flow test, ignition test and combustion test of the sub-scale combustor are also given in this paper. The sub-scale combustor uses liquid oxygen(LOx) and kerosene as propellants and has a injector head, an ablative material combustor wall and a water cooled nozzle. The injector head has LOx manifold, fuel manifold, fire face plate, one center swirl injector and 18 main swirl injectors. The cold flow, ignition and combustion tests were successfully performed without damage of combustor. Results of hot firing tests show that combustion efficiency meets the target of design and operations of start and stop cyclogram are stable and high frequency combustion instability does not occur.

• Journal of the Korean Society of Propulsion Engineers
• /
• v.7 no.1
• /
• pp.18-27
• /
• 2003

To perform combined tests with propellant feeding system and engine, which were developed for KSR-III launcher, vertical test stand was organized and a series of hot-fire combustion tests were carried out with engines of several injector faceplate types. In hot-fire tests in vertical installation, combustion instabilities occurred right after ignition with an engine without baffle, and such combustion instabilities did not occur at ignition add during mainstage operation for an engine with STS or composite baffle. 1.regular and temporary pressure pulsations(popping) were detected during steady operation with a baffle engine, however a development to combustion instabilities with resonant mode was highly suppressed by baffle. With a series of tests, it was confirmed that the last developed engine, which has composite baffle, was operated successfully in KSR-III flight propulsion system.

• Journal of the Korean GEO-environmental Society
• /
• v.2 no.2
• /
• pp.5-12
• /
• 2001

The physical characteristics and contaminant level of the dredged material generated by the channel maintenance and water quality improvement was analysed in a series of the study of the beneficial uses of dredged material in harbor. Dredged materials were sampled at Kunsan, Kohyun, Samchunpo, and Pohang Harbors and tested in the laboratory(leaching Test). From the experimental results, the specific gravity does not shows large differences, while almost grains are composed of silts and oyster shells except Pohang harbor containing gravels. The COD release rate and ignition loss is high in Kunsan dredged materials because of the watershed pollutants loads. The nutrient release rate is also relatively high. The release concentration of the heavy metals shows the highest values on Zn, Pb, Cd, Cu constituents at Kohyun, Kunsan, Samchunpo, Kunsan, respectively.

• Journal of the Society of Disaster Information
• /
• v.15 no.1
• /
• pp.98-108
• /
• 2019

Purpose: The purpose of this study is to test the sprinkler performance to protect the wall and ceiling joints of the sandwich panel warehouse in case of fire. Method: Based on the field surveys, test was setup and combustibles were prepared. The sprinkler discharge tests were performed at the corner of the wall and right under the sprinkler head. Results: It has been found that operation of the K-80 closed sprinkler head prevents the ignition of the sandwich panel and therefore no damage to the joints of sandwich panels. To prevent skipping phenomenon, it is necessary to install the sprinkler head from the corner of the wall and to keep a minimum distance of 2.4m and a maximum distance of 3m. Conclution: A Standard Operation Procedure should be prepared to suppress and rescue of fire brigade for a sandwich panel warehouse protected by perimeter sprinklers preventing a ignition of core materials and control fire.

• Journal of the Korea Safety Management & Science
• /
• v.15 no.2
• /
• pp.63-69
• /
• 2013

The purposes of this study are to survey stereotypes of control-display relationships for seven principal controls in passenger cars using the paper-pencil and hardware tests, and to examine stereotype strength of the paper-pencil test through comparing the stereotypes for the controls derived by the two methods. Ninety two and 60 college-aged students participated in the paper-pencil test and the real car simulation of the hardware test, respectively. There are dominant motion-directions for all controls in the paper-pencil test, while in the hardware test, there are dominant motion-directions for six controls including head light, high beam, door window, ignition key, door key and door lock controls. The stereotypes of motion-directions for six controls obtained by the paper-pencil test were the same as or similar to those by the hardware test. It was inferred from this that the congruence of the stereotypes by the two methods might be attributed to two simple motion-direction principles of 'clockwise for increase' and 'upward for increase.' Although it is known that the hardware test would be best for obtaining accurate stereotypes between controls and displays, this study implies that if the paper-pencil test is well designed, the paper-pencil test can produce the same results as the hardware test at low cost and without consuming time.

• Fire Science and Engineering
• /
• v.34 no.2
• /
• pp.14-21
• /
• 2020

This paper presents the study of a fire risk to the backside of two miniatures of ISO 9705 2/5 using a lightweight partition for indoor space division and reproduction of the ISO 9705 test. An SGP partition, stud partition, glass wool panel, urethane foam panel, sandwich panel, and glass partition were selected as the test specimens, which are frequently used in construction. According to the ISO 9705 test standard, stabilization was achieved using a measuring device that recorded data before the ignition of a burner and continued recording for 120 s thereafter. After ignition was achieved, the power was increased to 300 kW for 600 s and then reduced to 100 kW for 600 s. The specimens were subsequently observed for 180 s, and the fire risk to the backside and the fire pattern of the wall unit were analyzed. Owing to the amount of heat generated by the ignition source, the maximum temperature of the backside was observed to be 67.7 ℃ for the SGP partition, 55.1 ℃ for the stud partition, 52.4 ℃ for the glass wool panel, 727.4 ℃ for the sandwich panel, 561 ℃ for the urethane foam panel, and 630.5 ℃ for the glass partition. In the cases of the sandwich and urethane foam panels, the explosion of flammable gas occurred by virtue of fusion of the interior materials. The reinforced glass was fractured owing to the temperature difference between the heat- and nonheat-responsive parts. Ultimately, the fire risk to the nearby section room was deemed to be high.

• Journal of the Korean Society of Safety
• /
• v.20 no.4 s.72
• /
• pp.171-179
• /
• 2005

It is essential to understand the role of wall lining materials when they are exposed to a fire from an ignition source. Full-scale test methods permit an assessment of the performance of a wall lining material. Fire growth models have been developed due to the costly expense associated with full-scale testing. The models require heat flux maps from the ignition burner flame as input data. Work to date was impeded by a lack of detailed spatial characterization of the heat flux maps due to the use of limited instrumentation. To increase the power of fire modeling, accurate and detailed heat flux maps from the ignition burner are essential. High level spatial resolution for surface temperature can be provided from an infrared camera. The objective of this study was to develop a heat flux mapping procedure for a room test burner flame to a wall configuration with surface temperature information taken from an infrared camera. A prototype experiment was performed using the ISO 9705 test burner to demonstrate the developed heat flux mapping procedure. The results of the experiment allow the heat flux and spatial resolutions of the method to be determined and compared to the methods currently available.

• Journal of Mechanical Science and Technology
• /
• v.14 no.1
• /
• pp.103-112
• /
• 2000

Numerical simulations of unsteady opposed-flow flames are performed using an adaptive time integration method designed for differential-algebraic systems. The compressibility effect is considered in deriving the system of equations, such that the numerical difficulties associated with a high-index system are alleviated. The numerical method is implemented for systems with detailed chemical mechanisms and transport properties by utilizing the Chemkin software. Two test simulations are performeds hydrogen/air diffusion flames with an oscillatory strain rate and transient ignition of methane against heated air. Both results show that the rapid transient behavior is successfully captured by the numerical method.