• Composites Research
• /
• v.25 no.5
• /
• pp.136-140
• /
• 2012

This paper describes the bone healing process of fractured long bones such as a tibia applied by composite IM rods using finite element analysis. To simulated tissue differentiation process mechano-regulation theory with a deviatoric strain was implemented and a user's subroutine programmed by a Python code for an iterative calculation was used. To broadly find the appropriate rod modulus for healing bone fractures, composite IM rods were analyzed considering the stacking sequence. To compare mechanical stimulation at fracture gap, two kinds of initial loading conditions were applied. As a result, it was found that the initial loading condition was the most sensitive factor for the healing performance. In case a composite IM rod made of a plain weave carbon fiber/epoxy (WSN3k) had a stacking sequence of $[{\pm}45]_{nT}$, the healing efficiency was the most effective under a initial load of 10%BW.

• Proceedings of the Korean Nuclear Society Conference
• /
• 2002.10a
• /
• pp.125-125
• /
• 2002

• Proceedings of the Korean Nuclear Society Conference
• /
• 1995.10a
• /
• pp.480-486
• /
• 1995

Turbulent flow field in a subchannel of bare rod bundles has been numerically simulated using the control volume based finite element method. Launder & Ying model of Reynolds stress and Lam & Bremhorst low-Reynolds number model are implemented in k-$\varepsilon$ equations and momentum equations. Secondary flows are simulated using the stream function and vorticity approach. The control volume based finite element method enable to use the upwind scheme (donor cell scheme). Sensitivity of the constants in the models are studied, and proper values are found to get the close result to the measured flow distributions.

• The Journal of the Acoustical Society of Korea
• /
• v.28 no.8
• /
• pp.796-805
• /
• 2009

In this paper, a fabrication process for PZT preform of 1-3 type piezo-composite were studied using powder injection molding (PIM). The viscosity and the Pressure-Volume-Temperature (PVT) characteristics of the fabricated PZT feedstock were analyzed. The filling patterns, pressure, temperature distributions, and forming defects of the preform were analyzed with 3D TIMON commercial packages during PIM process. Also the fabrication conditions and the delivery system of the preform were optimized during the entire PIM process. Based on the simulated results, the preform having uniform distributions of the PZT rod was fabricated with the PIM process.

• Proceedings of the Korean Society for Technology of Plasticity Conference
• /
• 2004.08a
• /
• pp.307-316
• /
• 2004

This study examined the cause of the wrinkle defect which is frequently encountered in wire rod rolling of low carbon steel$(C0.08\~0.13wt.\%)$. Even a small defect on the surface of rolled bars can easily develop into fatal cracks during cold heading process of low carbon steel, and it is therefore necessary to minimize inherent defects on the surface of hot rolled bars. Hot rolling process of low carbon steel was analyzed to identify the cause of the wrinkle defect in conjunction with FE analysis. The integrated analysis revealed that the wrinkle defect initiated in the first stage of rolling, and it was at the billet edge where severe deformation and drastic temperature drop were present. To elucidate the micro-mechanical mechanism of the wrinkle defect, hot compression tests were carried out at various temperatures and strain rates using Gleeble-3800. The surface profile of the each other compressed specimens was compared, and rough surface lines were observed at relatively low temperatures. Those surface defects can develop into wrinkles during multi-pass rolling. To control the wrinkle defect in rolling, it is necessary to design an adequate caliber which can minimize the loss of ductility, and thereby prevent flow localization. To use the result of this study fur other steels, the quantitative measure of the wrinkle defect and flow localization parameter should be proposed.

• Journal of the Korean Society for Precision Engineering
• /
• v.17 no.12
• /
• pp.145-150
• /
• 2000

Micro punching is one of general methods to fabricate simple holes such as permanent ink-jet printer nozzles. A thin punch, that is need for micro punching, usually has been obtained by mechanical machining. There are some method to obtain a thin punch from a cylindrical rod, e.g., microgrinding and WEDG (Wire Electro-Discharge Grinding). Inefficiently, only one punch can be obtained from these machining methods. In contrast with these methods, many punches can be fabricated simultaneously by electrochemical process. Electrochemical process has usually aimed to obtain very sharp probe for atomic force microscopy (AFM) or scanning tunneling microscopy (STM), and it has not been considered the whole shape of a probe in spite of good merits. In this paper, an ultrathin punch with a tapered shape and a cylindrical tip is newly fabricated by electrochemical process.

• Food Engineering Progress
• /
• v.22 no.4
• /
• pp.381-385
• /
• 2018

Various rheological methods to measure the hardness of instant cooked rice by a texture analyzer were investigated and compared. Specifically, instant white rice samples with a wide range of hardness were subjected to four different rheological tests with disk, cylinder, rod, and cone probe whose results were inter-correlated. All the measurements demonstrated that the hardness of instant rice was reduced with increasing moisture content and showed negatively linear relationships. Out of the four tests applied in this study, the highest coefficient of correlation ($R^2=0.9268$) was observed distinctly in the cone probe test, where both compressive and shear forces can be applied to deform individual rice grains. However, the cylinder probe test had the lowest coefficient of correlation ($R^2=0.7247$) because it may be ineffective in causing direct deformation of individual rice grains. Furthermore, when the hardness values (N) were converted to stress (Pa), highly linear correlations ($R^2{\approx}0.99$) were observed between the tests with similar probe geometry and force application.

• Journal of the Korean Society for Precision Engineering
• /
• v.9 no.1
• /
• pp.29-33
• /
• 1992

A non-contact torque sensor was developed using amorphous alloy. The change of maixmum magnetic induction of C0-based amorphous alloy under the tensile and compressive stress was proportional to applied torque. For the construction of the torque sensor, a glass fiber reinforced-epoxy rod was used as shaft. The amorphous strips were attached on the epoxy shaft in the direction of $+45^{\circ}$and $-45^{\circ}$. The magnetizing coil and 2 sensing coil was installed. The static and dynamic test was carried out. The linearity and sensor hysteresis of the torque sensor was less than 1%.

• CDE review
• /
• v.21 no.2
• /
• pp.27-30
• /
• 2015

Smartphone users are 15 billion in all round the world, and Korean smartphone users are estimated at 40million people to 83% of the Korean population. Selfie stick is most popular item among 20, 30's age users. And they use smartphones more than 90%. In survey they express inconvenience of using selfie stick. Inconveniences are as follows. * Heavy * Handle is inconvenient. * Mistiming during taking pictures * the range of shooting is not enough. In this paper the first improvement was that rod strength is slightly stronger. The second we divide a grip into 3 parts. If 3 parts are unfolded, these can use for tripod. We use deflection Interpretation for main Finite Elements Method program.

• Journal of the Korean Ceramic Society
• /
• v.36 no.4
• /
• pp.417-424
• /
• 1999

Laser lapping of diamond films is performed with focused beam of copper vapor laser. Both spherical and rod-shape laser beam are used. Diamond surface is scanned at various scan speeds(0,125, 0.5, 0.75 mm/sec) and baem shifts (5, 10, 20, 40, 100$\mu\textrm{m}$) At 0.125 mm/sec 10$\mu\textrm{m}$ scan condition the level difference of di-amond surface of about 700$\mu\textrm{m}$ over 20 mm is reduced to 200$\mu\textrm{m}$ In addition surface roughness is also im-proved from 3.53$\mu\textrm{m}$ to 2.47$\mu\textrm{m}$ at 5$\mu\textrm{m}$ beam shift. But at higher beam shift than 10$\mu\textrm{m}$ laser scan makes the surface rougher which is considered to be due to the non uniform spatial distribution of laser en-ergy. It is concluded that homogenized laser beam with high average power is needed for large area laser lapping of diamond films at appreciable rates.