• Journal of Positioning, Navigation, and Timing
• /
• v.9 no.4
• /
• pp.337-345
• /
• 2020

In this paper, an efficient signal tracking method to simultaneously track both GPS L1 C/A and Galileo E1B CBOC(6,1,1/11) using a low cost GPU is proposed. In the existing method that each GNSS signal is processed within 1 ms, more than 2 ms processing time is required in GPU to process 4 ms CBOC signal. It means that real time operation is possible if only Galileo E1B CBOC signal is concerned. But when both GPS C/A and Galileo CBOC is required, it cannot process GPS C/A signal in real time. To process 1 ms GPS C/A and 4 ms Galileo CBOC signal in real time, 4 ms Galileo CBOC signal is divided into 4 by 1 ms signal block in the proposed method. Specially, a buffer that simultaneously manages 1 ms and 4 ms signals is designed. In addition, a module that accumulates the 1 ms correlation value of the Galileo CBOC by 4 ms and passes it to the PLL and DLL is implemented. The operation and performance are evaluated with real measurements in the GPU based SDR. The experimental results show that tracking of more than 16 satellites of GPS C/A and Galileo E1B is possible using the proposed method.

• ETRI Journal
• /
• v.36 no.3
• /
• pp.352-360
• /
• 2014

This paper presents a 900 MHz zero-IF RF transceiver for IEEE 802.15.4g Smart Utility Networks OFDM systems. The proposed RF transceiver comprises an RF front end, a Tx baseband analog circuit, an Rx baseband analog circuit, and a ${\Delta}{\Sigma}$ fractional-N frequency synthesizer. In the RF front end, re-use of a matching network reduces the chip size of the RF transceiver. Since a T/Rx switch is implemented only at the input of the low noise amplifier, the driver amplifier can deliver its output power to an antenna without any signal loss; thus, leading to a low dc power consumption. The proposed current-driven passive mixer in Rx and voltage-mode passive mixer in Tx can mitigate the IQ crosstalk problem, while maintaining 50% duty-cycle in local oscillator clocks. The overall Rx-baseband circuits can provide a voltage gain of 70 dB with a 1 dB gain control step. The proposed RF transceiver is implemented in a $0.18{\mu}$ CMOS technology and consumes 37 mA in Tx mode and 38 mA in Rx mode from a 1.8 V supply voltage. The fabricated chip shows a Tx average power of -2 dBm, a sensitivity level of -103 dBm at 100 Kbps with PER < 1%, an Rx input $P_{1dB}$ of -11 dBm, and an Rx input IP3 of -2.3 dBm.

• Journal of the Korea Institute of Information and Communication Engineering
• /
• v.13 no.4
• /
• pp.629-635
• /
• 2009

The FSK duplex remote controlling wireless transmission units with a common local oscillator circuit for transmitter and receiver are designed and implemented in this paper. In the FSK full-duplex the channel frequency for Tx/Rx is allocated, a common switching oscillator circuit for Tx/Rx is designed in the FSK half-duplex scheme. Both of FSK units get functions of automatic channel detection for busy channels and channel configuration for an idle channel in order to reduce the RF channel interference and are designed as a remote controller with small-sized low power of 10mW and the 400MHz-colpitz type PLL configuration of 50kHz channel separation. The full-duplex Tx/Rx link frequency gets frequency difference of 42.8MHz, which is double of 21.4MHz IF frequency.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.15 no.11
• /
• pp.1043-1050
• /
• 2004

In this paper, Phase noise is analyzed and a novel approach of the nonlinear approximation including second order term of phase noise is presented to analyze and quantize system performance. As results, in QPSK-OFDM system, when PLL loop bandwidth is 5.0 Hz, 1.0 kHB, 0.5 kHz respectively, there are about 0.6 dB, 1.0 dB, 1.7 dB SNR penalties at BER=10$\^$-4/ compared with system without phase noise in AWGN channel. In 16QAM modulation, there are about 1.9 dB, 3.2 dB, 6.7 dB SNR penalties at BER=10$\^$-4/ respectively. At QPSK-OFDM system, comparing the previous linear approximation method with our proposed nonlinear approximation method, there is similar BER performance at phase noise variance lower than 0.02, but certain difference occurs as variance increases more than 0.02. Furthermore, analytical BER results closely match with simulation results in the OFDM system employing QPSK and 16qAM modulation. And, BER performance of QPSK-OFDM system is considerably degraded because of the BER error floor if the phase noise variance becomes larger than 0.03.

• Journal of the Institute of Electronics and Information Engineers
• /
• v.54 no.4
• /
• pp.25-31
• /
• 2017

This paper presents a 270/540/750/1500-Mb/s serial-data transmitter realized in a $0.13-{\mu}m$ CMOS technology for the applications of video data transmission. A low-cost RG-58 copper cable(5C-HFBT-RG6T) is exploited as a transmission medium connected to a single BNC connector, which shows cable loss 45 dB in maximum at 1.5 GHz. RLGC modeling provides an equivalent circuit for SPICE simulations of which characteristics are very similar to the measured cable loss. The loss can be compensated by pre-emphasis at transmitter and equalization at receiver if needed. Measurements of the proposed transmitter chip demonstrate the operations of 270-Mb/s, 540-Mb/s, 750-Mb/s and 1.5-Gb/s, and provide the output voltage levels of $370mV_{pp}$ at 1.5 Gb/s even with the pre-emphasis turned-off. The total power consumption is 104 mW from 1.2/3.3-V supplies and the chip occupies the area of $1.65{\times}0.9mm^2$.

• The Journal of Korean Institute of Information Technology
• /
• v.16 no.11
• /
• pp.61-68
• /
• 2018

This paper describes design of a 10.525 GHz self oscillating mixer semiconductor IC chip combining voltage controlled oscillator and frequency mixer using silicon CMOS technology for Doppler radar applications. The p-core type VCO included in the self oscillating mixer minimizes the noise contained in the transmitted signal. This noise minimization increases the sensing distance and acts in a direction favorable to the reaching distance and the sensitivity of the motion detection sensor. Simulation results for phase noise show that a VCO designed as a P-core has a noise characteristic of -106.008 dBc / Hz at 1 MHz offset and -140.735 dBc / Hz at 25 MHz offset compared to a VCO designed with N-core and NP-core showed excellent noise characteristics. If a self-oscillating mixer is implemented using a p-core designed VCO in this study, a motion sensor with excellent range and reach sensitivity will be produced.

• Progress in Medical Physics
• /
• v.19 no.1
• /
• pp.42-48
• /
• 2008

Bio-implantable devices such as heart pacers, gastric pacers and drug-delivery systems require power for carrying out their intended functions. These devices are usually powered through a battery implanted with the system or are wired to an external power source. This paper describes an inductive power transmission link, which was developed for an implantable stimulator for direct stimulation of denervated muscles. The carrier frequency is around 1MHz, the transmitter coil has a diameter of 46mm, and the implant coil is 46mm. Data transmission to the implant with amplitude shift keying (ASK) and back to the transmitter with passive telemetry can be added without major design changes. We chose the range of coil spacing (2 to 30mm) to care for lateral misalignment, as it occurs in practical use. If the transmitter coil has a well defined and reliable position in respect to the implant, a smaller working range might be sufficient. Under these conditions the link can be operated in fixed frequency mode, and reaches even higher efficiencies of up to 37%. The link transmits a current of 50 mA over a distance range of 2-15 mm with an efficiency of more than 20% in tracking frequency. The efficiency of the link was optimized with different approaches. A class E transmitter was used to minimize losses of the power stage. The geometry and material of the transmitter coil was optimized for maximum coupling. Phase lock techniques were used to achieve frequency tracking, keeping the transmitter optimally tuned at different coupling conditions caused by coil distance variations.