• 한국정보통신학회논문지
• /
• 제11권3호
• /
• pp.570-576
• /
• 2007

본 연구에서는 field-dependent polarization 모델과 square-law FET 모델을 이용하여 Metal- ferroelectic-semiconductor FET (MFSFET) 소자의 특성을 연구하였다. 게이트 전압에 따른 드레인 전류특성에서 강유전체 박막의 항전압이 0.5 와 1 V 일 때, 각각 1와 2 V의 메모리 창 (memory window) 을 나타내었다. 드레인 전류-드레인 전압곡선에서 두 부분의 문턱전압에 의해 나타난 포화 드레인 전류차이는 게이트 전압이 0, 0.1, 0.2, 0.3 V 일 때, 각각 1.5, 2.7, 4.0, 5.7 mA로 명확한 차이를 나타내었다. PLZT(10/30/70), PLT(10), PZT(30/70) 박막의 이력곡선 시뮬레이션과 리텐션 특성의 fitting 결과를 바탕으로 시간경과 후의 드레인 전류를 분석한 결과, PLZT(10/30/70) 박막이 10년 후에도 약 18%의 포화 전류가 감소하는 가장 우수한 신뢰성을 나타내었다.

• Journal of Magnetics
• /
• 제6권2호
• /
• pp.47-52
• /
• 2001

We present the magnetisation reversal dynamics of epitaxial Fe thin films grown on GaAs(001) and InAs(001) studied as a function of field sweep rate in the range 0.01-160 kOe/s using magneto-optic Kerr effect (MOKE). For 55 and 250 ${\AA}$ Fe/GaAs(001), we find that the hysteresis loop area A follows the scaling relation $A\propto H_{\alpha} \;with\; \alpha=0.03\sim0.05$ at low sweep rates and 0.33~0.40 at high sweep rates. For the 150${\AA}$ Fe/InAs(001) film, $\alpha$is found to be ~0.02 at low sweep rates and ~0.17 at high sweep rates. The differing values of $\alpha$ are attributed to a change of the magnetisation reversal process with increasing sweep rate. Domain wall motion dominates the magnetisation reversal at low sweep rates, but becomes less significant with increasing sweep rate. At high sweep rates, the variation of the dynamic coercivity $H_c{^*}$ is attributed to domain nucleation dominating the reversal process. The results of magnetic relaxation studies for easy-axis reversal are consistent with the sweeping of one or more walls through the entire probed region (~100$\mu m$). Domain images obtained by scanning Kerr microscopy during the easy cubic axis reversal process reveal large area domains separated by zigzag walls.

• 한국재료학회지
• /
• 제29권2호
• /
• pp.73-78
• /
• 2019

Lead free $(Ba_{0.7}Ca_{0.3})TiO_3$ thick films with nano-sized grains are prepared using an aerosol deposition (AD) method at room temperature. The crystallinity of the AD thick films is enhanced by a post annealing process. Contrary to the sharp phase transition of bulk ceramics that has been reported, AD films show broad phase transition behaviors due to the nano-sized grains. The polarization-electric hysteresis loop of annealed AD film shows ferroelectric behaviors. With an increase in annealing temperature, the saturation polarization increases because of an increase in crystallinity. However, the remnant polarization and cohesive field are not affected by the annealing temperature. BCT AD thick films annealed at $700^{\circ}C/2h$ have an energy density of $1.84J/cm^3$ and a charge-discharge efficiency of 69.9 %, which is much higher than those of bulk ceramic with the same composition. The higher energy storage properties are likely due to the increase in the breakdown field from a large number of grain boundaries of nano-sized grains.

• Wind and Structures
• /
• 제27권6호
• /
• pp.381-397
• /
• 2018

Nonlinear behavior in fluid-structure interaction (FSI) of bridge decks becomes increasingly significant for modern bridges with increasing spans, larger flexibility and new aerodynamic deck configurations. Better understanding of the nonlinear aeroelasticity of bridge decks and further development of reduced-order nonlinear models for the aeroelastic forces become necessary. In this paper, the amplitude-dependent and neutral angle dependent nonlinearities of the motion-induced loads are further highlighted by series of computational fluid dynamics (CFD) simulations. An effort has been made to investigate a semi-analytical time-domain model of the nonlinear motion induced loads on the deck, which enables nonlinear time domain simulations of the aeroelastic responses of the bridge deck. First, the computational schemes used here are validated through theoretically well-known cases. Then, static aerodynamic coefficients of the Great Belt East Bridge (GBEB) cross section are evaluated at various angles of attack, leading to the so-called nonlinear backbone curves. Flutter derivatives of the bridge are identified by CFD simulations using forced harmonic motion of the cross-section with various frequencies. By varying the amplitude of the forced motion, it is observed that the identified flutter derivatives are amplitude-dependent, especially for $A^*_2$ and $H^*_2$ parameters. Another nonlinear feature is observed from the change of hysteresis loop (between angle of attack and lift/moment) when the neutral angles of the cross-section are changed. Based on the CFD results, a semi-analytical time-domain model for describing the nonlinear motion-induced loads is proposed and calibrated. This model is based on accounting for the delay effect with respect to the nonlinear backbone curve and is established in the state-space form. Reasonable agreement between the results from the semi-analytical model and CFD demonstrates the potential application of the proposed model for nonlinear aeroelastic analysis of bridge decks.

• 대한금속재료학회지
• /
• 제49권2호
• /
• pp.112-120
• /
• 2011

The out-of-phase thermo-mechanical fatigue (OP TMF) in a <001> oriented single crystal nickel-based superalloy CMSX-4 has been studied. OP TMF life was less than a half of low cycle fatigue(LCF) life in spite of a small hysteresis loop area of OP TMF compared to that of LCF. The failure was caused by the initiation of a crack at the oxide-layered surface followed by its planar growth along the <100> ${\gamma}$ channel in both LCF and OP TMF. However, deformation twins appeared near the major crack of OP TMF. The multiple groups of parallel twin plates on {111} planes provided a preferential path for crack propagation, which caused a significant decrease in OP TMF life. Additionally, the analysis on the surface crack morphology revealed that the tensile strain at the minimum temperature of OP TMF was found to accelerate the crack propagation.

• Tribology and Lubricants
• /
• 제36권6호
• /
• pp.332-341
• /
• 2020

High-speed turbomachinery implements gas foil bearings (GFBs) due to their distinctive advantages, such as high efficiency, lesser part count, and lower weight. This paper provides the test results of the static structural stiffnesses and loss factors of bump-type foil thrust bearings with increasing preload and bearing deflection. The focus of the current work is to experimentally quantify variability in structural stiffnesses and loss factors among the four test thrust bearings with identical design values and material of the bump and top foil geometries using the same (open-source) fabrication method. A simple test setup, using a rigidly mounted non-rotating shaft and thrust disk, measures the bearing bump deflections with increasing static loads on the test bearing. The inner and outer diameters of the test bearings are 41 mm and 81 mm, respectively. The loss factor, best-representing energy dissipation in the test bearings, is estimated from the area inside the local hysteresis loop of the load versus the bearing deflection curve. The measurements show that structural stiffnesses and loss factors of the test bearings significantly rely on applied preloads and bearing deflections. Local structural stiffnesses of the test bearings increase with applied preloads but decrease with bearing deflections. Changes of loss factors are less sensitive to applied preloads and bearing deflections compared to those of structural stiffnesses. Up to 35% variability in static load structural stiffnesses is found between bearings, while up to 30% variability in loss factors is found between bearings.

• 한국구조물진단유지관리공학회 논문집
• /
• 제26권3호
• /
• pp.48-54
• /
• 2022

본 연구는 균열에 의한 콘크리트 전단벽 강성저하 영향 평가를 위해 수행되었으며, 극한 내지진 하중의 60%까지 재하한 비선형 해석 결과, 사전 균열효과에 의해 비손상 대비 진동수의 12%정도 진동수가 감소하였으며 강성 측면에서 23%정도의 감소현상을 나타냈다. 단계적으로 지진하중의 크기를 증가시킨 비선형 해석 결과, 지진하중의 세기가 커짐에 따라 콘크리트 전단벽체에 전단균열이 발생하여 진전함을 파악하고, 반복이력에 의한 에너지 손실과 강성 저하가 뚜렷하게 발생함을 알 수 있었다. 또한 두 가지 콘크리트 강도와 전단벽 제원에 대하여 지진하중의 크기가 극한 내지진 하중에 근접함에 따라 진동수의 감소량은 비손상 대비 10~40%정도로 나타났으며, 강성의 경우 비손상 대비 40%정도 수준까지 감소할 수 있는 것으로 나타났다.

• 한국전산구조공학회논문집
• /
• 제35권6호
• /
• pp.381-386
• /
• 2022

본 논문에서는 휨 항복 메커니즘을 기반으로 한 강재이력 댐퍼를 제안하기 위한 해석 및 실험적 연구를 수행하였다. 댐퍼는 휨모멘트에 의한 항복거동을 하도록 설계된 일련의 댐핑 플레이트로 구성된다. 실험 결과와 유한요소해석 결과의 비교를 통해서 본 연구에서 채택된 해석적 접근방식이 댐핑 플레이트의 형태 및 상세에 대한 민감도 연구를 수행하기에 적절함을 확인하였다. 최초에 제안된 댐퍼는 휨 항복 메커니즘을 기반으로 작동하는 것으로 고안되었으나, 댐핑 플레이트의 인장 거동에 대한 기여도가 상당할 수 있음을 관찰할 수 있었다. 댐핑 플레이트의 두께가 증가함에 따라 휨 항복에 의한 에너지 흡수량이 증가한다. 댐핑 플레이트의 두께가 감소함에 따라 인장에 의한 댐퍼의 비선형 거동 기여도가 증가하고 좌굴 발생으로 인하여 이력곡선의 형상이 댐퍼로서 불리해진다.

• Steel and Composite Structures
• /
• 제46권6호
• /
• pp.793-804
• /
• 2023

In this study, cyclic loading tests were conducted to assess the seismic performance of cast-in-place (CIP) concrete-filled hollow core precast concrete columns (HPCC) constructed using steel ducts and rubber tubes. The outer shells of HPCC, with a hollow ratio of 47%, were fabricated using steel ducts and rubber tubes, respectively. Two combinations of shear studs & long threaded bars or cross-deformed bars & V-ties were employed to ensure the structural integrity of the old concrete (outer shell) and new CIP concrete. Up to a drift ratio of 3.8%, the hysteresis loop, yielding stiffness, dissipated energy, and equivalent damping ratio of the HPCC specimens were largely comparable to those of the solid columns. Besides the similarities in cyclic load-displacement responses, the strain history of the longitudinal bars and the transverse confinement of the three specimens also exhibited similar patterns. The measured maximum moment exceeded the predicted moment according to ACI 318 by more than 1.03 times. However, the load reduction of the HPCC specimen after reaching peak strength was marginally greater than that of the solid specimen. The energy dissipation and equivalent damping ratios of the HPCC specimens were 20% and 25% lower than those of the solid specimen, respectively. Taking into account the overall results, the structural behavior of HPCC specimens fabricated using steel ducts and rubber tubes is deemed comparable to that of solid columns. Furthermore, it was confirmed that the two combinations for securing structural integrity functioned as expected, and that rubber air-tubes can be effectively used to create well-shaped hollow sections.

• Earthquakes and Structures
• /
• 제23권2호
• /
• pp.129-138
• /
• 2022

One of the objectives to prevent building pounding between two adjacentstructures is to considerseparation distance or decrease relative displacement during seismic excitation. Although the majority of building codes around the world have basically suggested some equations or approximately recommended various distances between structuresto avoid pounding hazard, but a lot of reportsin zone of pounding have obviously shown thatsafety situation or economic consideration are not always provided due to the collisions between buildings and the cost of land, respectively. For this purpose, a dynamic MDOF model by having base isolation system is numerically considered and using various earthquake records, relative displacements are mathematically investigated. Different equations to determine the value of damping ratio are collected and the results of evaluations are listed for comparison among them to present a new equation for determination of impact damping ratio. Presented equation is depends significantly on impact velocity before and after impact based on artificial neural network, which the accuracy of them is investigated and also confirmed. In order to select the optimum equation, hysteresisloop of impact between base of building and rubber bumper is considered and compared with the hysteresis loop of each impact, calculated by different equations. Finally, using representative equation, the effect of thickness, number and stiffness of rubber bumpers are numerically investigated. The results of analysis indicate that stiffness and number of bumpers have significantly affected in zone of impact force while the thickness of bumpers have not shown significant influence to calculate impact force during earthquake. For instance, increasing the number of bumpers, gap size between structures and also the value of stiffness is caused to decrease impact force between models. The final evaluation demonstrates that bumpers are able to decrease peak lateral displacement of top story during impact.