• Structural Engineering and Mechanics
• /
• v.71 no.6
• /
• pp.699-712
• /
• 2019

The reinforced concrete lining of hydraulic pressure tunnels tends to crack under high inner water pressure (IWP), which results in the inner water exosmosis along cracks and involves typical hydro-mechanical interaction. This study aims at the development, validation and application of an indirect-coupled method to simulate the lining cracking process. Based on the concrete damage plasticity (CDP) model, the utility routine GETVRM and the user subroutine USDFLD in the finite element code ABAQUS is employed to calculate and adjust the secondary hydraulic conductivity according to the material damage and the plastic volume strain. The friction-contact method (FCM) is introduced to track the lining-rock interface behavior. Compared with the traditional node-shared method (NSM) model, the FCM model is more feasible to simulate the lining cracking process. The number of cracks and the reinforcement stress can be significantly reduced, which matches well with the observed results in engineering practices. Moreover, the damage evolution of reinforced concrete lining can be effectively slowed down. This numerical method provides an insight into the cracking process of reinforced concrete lining in hydraulic pressure tunnels.

• Journal of the Korean Society of Hazard Mitigation
• /
• v.10 no.5
• /
• pp.159-168
• /
• 2010

This study investigates the relationships between the maximum freshwater pumping discharge and hydraulic properties of coastal aquifer using a laboratory model. The experiment performed the fresh pumping test in various locations near the saltwedge induced by saltwater intrusion to freshwater over aquifer characteristics of hydraulic conductivity, salinity, and ground surface slope. Saltwater pumping also tested to protest saltwater intrusion to the excessively discharging freshwater well. The maximum freshwater discharges were achieved, and then the optimum saltwater discharges were measured. It is found that greater hydraulic conductivity and ground surface slope produced greater the maximum freshwater pumping discharge. Salinity gave less impact on the pumping discharge relatively. Higher freshwater discharge was found at higher hydraulic conductivity and steeper ground surface slope. The optimum saltwater discharge required 14% more pumping rate than the maximum freshwater discharge to keep saltwater intrusion to the freshwater pumping well. Pumping well located closer to salt-wedge profile promoted less freshwater pumping discharge. Therefore, pumping well location, hydraulic conductivity, ground surface slope, and salinity should be taken into account in freshwater pumping in coastal aquifer.

• Proceedings of the Korean Geotechical Society Conference
• /
• 2010.09a
• /
• pp.1002-1007
• /
• 2010

This study evaluates the electro-osmotic hydraulic conductivity for the clay specimen by applying the series of the voltage gradient simultaneously with different stress conditions. The test results shows that the shrinkage of voids corresponds to the linear decrease in the electro-osmotic seepage velocity, and the changes of electro-chemical characteristics in the specimen induces the gradual decrease of the electro-osmotic seepage velocity with the constant voltage gradient.

• Journal of the Korean Geotechnical Society
• /
• v.15 no.6
• /
• pp.111-120
• /
• 1999

Leachate flow behavior due to intermediate cover soil of low hydraulic conductivity and the applicability of pumping method for reducing the leachate level in the landfill are analyzed with the numerical flow model, MODFLOW. Using the hydraulic conductivity and storativity data obtained from the field pumping and slug tests(Jang and Cho, 1999), the hydraulic condition within the landfill is validated. The optimum rate of pumping, the radius of influence, and the efficiency of horizontal drain are analyzed for reducing the leachate level in the landfill. From the results of the analyses, the barrier effect that the buried cover soil of low hydraulic conductivity prevents the vertical movement of leachate flow through the cover soil, which is found from the in-situ geotechnical studies(Jang and Cho, 1999), is identified again. Also, the installation of horizontal drains to the pumping well can increase the pumping rate from 120 ton/day per a well to 300 ton/day. The length of horizontal drain did not influence significantly on the drawdown-time curve of leachate in the landfill.

• Proceedings of the Korean Society of Soil and Groundwater Environment Conference
• /
• 1998.11a
• /
• pp.76-80
• /
• 1998

In order to identify the cause of ground water drawdown of a piezometer installed around the LPG storage cavern, parameter estimations were conducted by inverse and forward numerical models. An inverse model, SK-EST developed by SK Engineering & Construction Co., Ltd.(SKEC,1997) was performed to estimate the change of the hydraulic conductivity. It was verified by the commercial forward model, AQUA3D (VATNASKIL,1995). The simulation results showed that the hydraulic diffusivity of the rock mass between the piezometer and the cavern had been increased and the change rate of the hydraulic head had been abruptly increased in response to the change of the operation pressure. Finally the statistical analysis for observed data showed the increase of the change rate of the hydraulic head and thus proved the applicability of SK-EST.

• Journal of the Korean Society of Groundwater Environment
• /
• v.3 no.2
• /
• pp.80-94
• /
• 1996

The Nanjido Landfill has recently become one of the most important environmental sites for a hydrogeological study. Hydrogeological study was performed by understanding the current situation, analyzing hydrogeological information, and constructing a hydrogeological data base. The constructed data base was used for the analyses of several important phenomena in the Nanjido Landfill. Saturated hydraulic conductivity and underground temperature were measured. Based on the hydraulic conductivity and rainfall data, net infiltration rates were estimated. Leachate production rates are estimated by using the data base. The data base and a hydraulic model were used to understand the formation of the so called floating leachate layer.

• Proceedings of the SAREK Conference
• /
• 2005.11a
• /
• pp.155-160
• /
• 2005

To purpose of this research is to develop the numerical model for simulating performance of ground heat exchanger with high prediction accuracy. This paper describes the development of a numerical model that simulates the heat transfer between ground and circulation water in ground heat exchanger. Furthermore, we propose the estimating technique of soil properties, such as thermal conductivity, heat capacity and hydraulic conductivity, based on ground investigation. Comparison between experiment and numerical analysis based on the model developed above was conducted under the condition of the experiment in 2004. The result of analysis agreed well with the experimental result.

• Journal of Korea Water Resources Association
• /
• v.42 no.11
• /
• pp.1005-1015
• /
• 2009

Saltwater intrusion in coastal aquifer was investigated using a laboratory model. Salt-wedge profiles were reproduced in a porous media tank 140 cm long, 70 cm high, and 10 cm wide. The experiments were performed with various conditions of porous media hydraulic conductivity, salinity, and ground surface slope to assess relationships on salt wedge location and inclination. Salt-wedge profiles induced by saltwater intrusion were observed in porous media equilibrium state, and compared with previously derived formulas of the Glover (1959), Henry (1959) and Strack (1976). It was found that salt-wedge shape and formations were affected by the water level ratio ($H_F/H_S$) due to high hydraulic conductivity, saltwater salinity and ground surface slope. High $H_F/H_S$ of porous media having high hydraulic conductivity shifted the saltwater interface toward the saltwater reservoir. Increasing surface slope of the porous media caused the salt-wedge profile inclination to decrease. Saltwater salinity also contributed to the location of saltwater interface, yet the impact was not more significant than hydraulic conductivity.

• Korean Journal of Soil Science and Fertilizer
• /
• v.43 no.4
• /
• pp.407-414
• /
• 2010

Until now, the pore size distribution, PSD, of soil profile has been calculated from soil moisture characteristic data by water release method or mercury porosimetry using the capillary rise equation. But the current methods are often difficult to use and time consuming. Thus, in this work, theoretical framework for an easy and fast technique was suggested to estimate the PSD from unsaturated hydraulic conductivity data in an undisturbed field soil profile. In this study, unsaturated hydraulic conductivity data were collected and simulated by the variation of soil parameters in the given boundary conditions (Brooks and Corey soil parameters, ${\alpha}_{BC}=1-5L^{-1}$, b = 1 - 10; van Genuchten soil parameters, ${\alpha}_{VG}=0.001-1.0L^{-1}$, m = 0.1 - 0.9). Then, $K_s$ (1.0 cm $h^{-1})$ was used as the fixed input parameter for the simulation of each models. The PSDs were estimated from the collected K(h) data by model simulation. In the simulation of Brooks-Corey parameter, the saturated hydraulic conductivity, $K_s$, played a role of scaling factor for unsaturated hydraulic conductivity, K(h) Changes of parameter b explained the shape of PSD curve of soil intimately, and a ${\alpha}_{BC}$ affected on the sensitivity of PSD curve. In the case of van Genuchten model, $K_s$ and ${\alpha}_{VG}$ played the role of scaling factor for a vertical axis and a horizontal axis, respectively. Parameter m described the shape of PSD curve and K(h) systematically. This study suggests that the new theoretical technique can be applied to the in situ prediction of PSD in undisturbed field soil.

• Proceedings of the Korean Society of Soil and Groundwater Environment Conference
• /
• 2002.09a
• /
• pp.28-31
• /
• 2002

The water level fluctuation (WLF) method is a conventional method for quantifying groundwater recharge by multiplying the specific yield to the water level rise. A 2-D unconfined flow model with a time series of the recharge rate is developed. It is used for elucidating the errors of the WLF method which is implicitly based on the tank model where the horizontal flow in the saturated zone is ignored. Simulations show that the recharge estimated by the WLF method is underestimated for the observation well near the discharge boundary. This is due to the fact that the hydraulic stress resulting from the recharge is rapidly dissipating by the horizontal flow near the discharge boundary Simulations also reveal that the recharge was significantly underestimated with increase in the hydraulic conductivity and the recharge duration, and decrease in the specific yield.