• 한국소음진동공학회:학술대회논문집
• /
• 한국소음진동공학회 2002년도 추계학술대회논문초록집
• /
• pp.347.1-347
• /
• 2002

A hybrid mount featuring elastic rubber and piezoelectric material is devised and applied to the vibration control of a beam structure. The governing equation of the beam structure associated with the hybrid mount is derived. Subsequently, a robust sliding mode controller is designed to attenuate the vibration of the beam structure due to external excitation. The controller is then simulated and control responses such as displatement and transmitted force are evaluated in time and frequency domains.

• 한국공간구조학회논문집
• /
• 제21권2호
• /
• pp.33-40
• /
• 2021

For the practical application of U-flanged Truss Hybrid beams, the flexural capacity of hybrid beams with end reinforcement details using vertical steel plates was verified. The bending test of U-flanged Truss Hybrid beams was performed using the same top chord under the compressive force, but with the thickness of the bottom plate and the amount of tensile reinforcement. The initial stiffness and maximum load of the specimen with tensile reinforcement have a higher value than that of the specimen without tension reinforcement, but the more tensile reinforcement, the greater the load decrease after the maximum load. In the case of the specimen with tensile reinforcement, because the test result value is 76% to 88% when compared with the flexural strength according to Korea Design Code, the safety of the U-flanged Truss Hybrid beam with the same details of the specimens can't ensure. Therefore, the development of new details is required to ensure that the bottom steel plate and the tensile reinforcement can undergo sufficient tensile deformation.

• 전기학회논문지P
• /
• 제63권3호
• /
• pp.200-205
• /
• 2014

In this paper, 5.8GHz band $4{\times}4$ Butler matrix is designed using easily accessible commercial $90^{\circ}$ hybrid coupler and semirigid coaxial cable as a transmission line. This Butler matrix is very flexible to changes of antenna system specification like a frequency band because $90^{\circ}$ hybrid coupler changing is all to do. The result of design is the distance of $2{\times}2$ array antenna element is $\sqrt{2}{\lambda}/4$, the 4 beam directions are diagonal of array antenna and phase shifter is not necessary. The beam width is roughly $25^{\circ}$ narrower because of array antenna geometry and the side lobe is about 10dB higher partially than theoretical beam pattern. But the overall beam pattern is similar with theoretical beam. This Butler matrix can be applied to switching beam antenna of 5.8GHz band Wi-Fi and WAVE system.

• 한국강구조학회 논문집
• /
• 제28권5호
• /
• pp.345-354
• /
• 2016

최근 합성 보-기둥 접합부를 위한 복합모멘트접합(hybrid moment connection)상세가 개발되었다. 기둥으로 팔각형태의 콘크리트 충전강관이 사용되었고, 보에는 U단면 콘크리트 충전강관이 사용되었다. 보-기둥 모멘트접합을 위해 보 강관은 기둥 강판에 직접 용접되었다. 하지만 보 하부 플랜지는 응력집중을 피하기 위하여 기둥 강판에 용접되지 않았고, 대신 보 플랜지의 인장력을 전달하기 위해 기둥 관통철근이 사용되었다. 기존 외다이어프램 보강상세 및 복합모멘트접합 상세를 갖는 총 4개의 실험체를 제작하고, 반복하중실험을 수행하였다. 실험결과 복합모멘트접합 상세는 보 플랜지의 인장력이 기둥 내부로 효과적으로 전달되었다. 또한, 하중재하능력 및 변형능력이 기존 외다이어프램 상세와 거의 동일한 수준으로 나타났다. 하지만, 최종 접합부 파괴모드는 복합모멘트접합 상세에 따라 영향을 받았다.

• Computers and Concrete
• /
• 제31권3호
• /
• pp.197-206
• /
• 2023

In this paper, the bending performance of a MSFRHPC (containing steel fiber, polyvinyl alcohol (PVA) fiber, and CW)-reinforced beam was studied for the first time. Introducing a multiscale fiber system increased the first crack load (up to 150%), yield load (up to 50%), and peak load (up to 15%) of reinforced beams. The multiscale fiber system delays cracking of the reinforced beam, reduces crack width of the reinforced beam in normal use, and improves the durability of the beam. Considering yield load and peak load, the reinforcing effect of multiscale fiber on the high-reinforcement ratio beam (1.00%) is better than that on the low-reinforcement ratio beam (0.57%). Introducing fibers slowed the development of cracks in the reinforced beam under bending. With the added hybrid fiber, the deformation concentration of reinforced beams after yield was more significant with concentration in 1 or 2 cracks. A model for predicting the flexural capacity of MSFRHPC-reinforced beams was proposed, considering the action of multiscale hybrid fibers. This research is helpful for structure application of MSFRHPC-containing CW.

• Computers and Concrete
• /
• 제19권1호
• /
• pp.79-85
• /
• 2017

This paper summarizes the experimental study of the shear behaviour of Hybrid Fibre Reinforced Concrete (HFRC) beams retrofitted by using externally bonded Glass Fibre Reinforced Polymer (GFRP) laminates. To attain the set-out objectives of the present investigation, steel fibre of 1% and polypropylene fibre of 0.30% was used for hybrid steel-polypropylene fibre reinforced concrete: whereas for hybrid glass-polypropylene fibre reinforced concrete, glass fibre by 0.03% and polypropylene fibre of 0.03% by volume of concrete was used. In this study, 9 numbers of beams were cast and tested into three groups (Group I, II & III). Each group containing 3 numbers of beams, out of which one serve as a control beam or a hybrid steel-polypropylene fibre reinforced concrete beam or a hybrid glass - polypropylene fibre reinforced concrete beam and the remaining two beams were preloaded until shear cracks appeared up to 75% of ultimate load and then preloaded beams (damaged beams) were retrofitted with GFRP laminates at shear zone in the form of strips, as one beam in vertical position and another beam in inclined position to restrict the shear cracks. Finally, the retrofitted beams were loaded until failure and test results were compared. The experimental tests have been conducted to investigate various parameters of structural performance, such as load carrying capacity, crack pattern and failure modes, load-deflection responses and ductility relations. The test results revealed that beams retrofitted using GFRP laminates considerably increased the load carrying capacity. In addition, it was found that beams retrofitted with inclined strip offers superior performance than vertical one. Comparing the test results, it was observed that hybrid steel-polypropylene fibre reinforced concrete beam retrofitted with GFRP laminates showed enhanced behaviour as compared to other tested beams.

• 콘크리트학회논문집
• /
• 제19권5호
• /
• pp.557-567
• /
• 2007

아파트의 지하주차장은 보 아래로 각종 설비 배관이 배치되기 때문에 층고가 $300{\sim}400mm$ 정도 추가로 필요하다. 본 연구에서는 설비 배관에 의한 층고 증가를 방지할 수 있도록 설비 배관이 배치되는 부분의 깊이를 줄이고 대신 강재 보를 매입하여 보강한 PC 보의 상부를 현장콘크리트로 타설하여 마무리하는 하이브리드 보 (hybrid beam)를 제안하였다. 그리고 이 하이브리드 보의 휨 거동을 검토하기 위해서 강재 의의 형상, 보의 깊이를 줄인 부분의 길이, 시공 단계 및 콘크리트 양생 후인 합성 단계, 슬래브 및 전단연결재 포함 여부 등을 주요 실험 변수로 실물 실험체 9개를 제작하고 휨 실험을 수행하였다. 그 결과, 본 연구에서 제안한 하이브리드 보는 합성 단계인 경우 강재 보의 형상, 보의 깊이를 줄인 부분의 길이, 슬래브 및 전단연결재의 포함 여부에 관계없이 설계 내력을 상회하는 우수한 휨 거동을 보여주는 것을 확인하였다. 시공 단계에서는 구조적 안정성 및 시공 품질의 확보를 위하여 가설 지지대 (support)가 필요한 것으로 판단된다.

• 한국강구조학회 논문집
• /
• 제25권1호
• /
• pp.47-59
• /
• 2013

본 연구는 신형상 U형 합성보의 1차 휨실험에 연이은 2차 연구로 U형 합성보와 기둥 접합부의 내진성능시험이다. 실험 변수는 기둥의 종류와 보 춤, 보 상부 플레이트 연속유무, 보 단부 철근 수 등으로 3개의 실험체를 제작하였다. 기둥의 종류는 철골 철근콘크리트 기둥과 CFT 형상의 ACT기둥이며, 보 춤은 300, 500(mm)이다. 접합부상세는 일반적으로 많이 적용하고 있는 짧은 브라켓을 활용한 볼트 접합부이다. 실험결과 변형능력은 2~4(%)의 층간변위각을 확보하였으며, 최대모멘트는 부휨모멘트의 경우 공칭모멘트 이상의 내력이 나타났다.

• 한국표면공학회지
• /
• 제44권4호
• /
• pp.155-164
• /
• 2011

Electron beam evaporation source is widely used to prepare thin films by physical vapor deposition because it is very effective to vaporize materials and there is virtually no limit to vaporize materials including metals and compounds such as oxide. In this study, evaporation characteristics of various metals and compounds from an electron beam evaporation source have been studied. The 180 degree deflection type electron beam evaporation source which has 6-hearth crucibles and is capable of inputting power up to 10 kW was employed for evaporation experiment. 36 materials including metals, oxides and fluorides have been tested and described in terms of optimum crucible liner, evaporation state, stability, and so on. Various crucible liners have been tried to find out the most effective way to vaporize materials. Two types of crucible liners have been employed in this experiment. One is contact type liner, and the other is non-contact type one. It has been tried to give the objective information and the most effective evaporation method on the evaporation of materials from the electron beam evaporation source. It is concluded that the electron beam evaporation source can be used to prepare good quality films by choosing the appropriate crucible liner.

• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 2009년도 하계학술대회 논문집
• /
• pp.392-393
• /
• 2009

The study is aimed at studying a weakly relativistic oversized BWO with a Bragg reflector entrance of SWS. The Bragg reflector reflects microwaves, while it is open for beam propagations. By changing the boundary condition at the beam entrance, the effect of the Bragg reflector on the BWO performance is examined.