• Journal of the Microelectronics and Packaging Society
• /
• v.29 no.2
• /
• pp.99-105
• /
• 2022

As the chip size gets smaller, the width of the electrode line is also fine, and the density of interconnections is increasing. As a result, RC delay is becoming a problem due to the difference in resistance between the capacitor layer and the electrical conductivity layer. To solve this problem, the development of electrodes with high electrical conductivity and dielectric materials with low dielectric constant is required. In this study, we developed low dielectric ink by mixing commercial PSR which protect PCB's circuits from external factors and PI with excellent thermal property and low-k characteristics. As a result, the ink mixture of PSR and PI 10:3 showed the best results, with a dielectric constant of about 2.6 and 2.37 at 20 GHz and 28 GHz, respectively, and dielectric dissipation was measured at about 0.022 and 0.016. In order to verify the applicability of future applications, various line-width transmission lines produced on Teflon were evaluated, and as a result, the loss of transmission lines using low dielectric ink mixed with PI was 0.12 dB less on average in S21 than when only PSR was used.

• Journal of the Korean Institute of Telematics and Electronics
• /
• v.21 no.3
• /
• pp.73-83
• /
• 1984

The performances of embedded adaptive differential pulse code modulation (ADPCM), embedded adaptive delta modulation (ADM), and the same systems with a delayedfecision scheme have been studied with real speech over a wide dynamic range. The embedded ADPCM and ADM coders have been obtained by modifying the conventional ADPCM and ADM coders. The basic scheme of the embedded ADPCM coder is based on the ADPCM originally proposed by Cummiskey et at. For embedded ADM systems, we have modified continuously variable slope DM (CVSD) and hybrid commanding DM (HCDM) systems. Among these embedded coders, the performance of the embedded HCDM is superior to the other coders over a wide range of transmission rate from 16 to 64 kbits/s, When the delayedtecision scheme is applied to the embedded ADPCM the performance is improved significantly at all transmission rates. But, in the embedded ADM systems with 16 kHz sampling rate, the performance improvement resulting from delayed decision is not drastic as is in the embedded ADPCM with the same number of delayed samples.

• Journal of IKEEE
• /
• v.9 no.2 s.17
• /
• pp.170-178
• /
• 2005

The video data corrupted by the transmission error due to packet loss induce error propagation in decoded video data, and cause poor video quality. To remedy these corrupted video data, there have been introduced two types of error concealment techniques: spatial or temporal error concealment algorithm. Computational overhead by using spatial error concealment algorithm is a serious disadvantage in mobile video data streaming environment. In this paper, we propose hybrid type error concealment technique recovering video quality of mobile device using MPEG-4 video streaming on error-prone wireless network. Our algorithm is implemented in MPEG-4 decoder. The algorithm adopts Intel Wireless MMX technology to provide high performance of portable embedded multimedia mobile device. It is proven that the proposed algorithm shows expected performance for a mobile streaming system(PDA) on IP channels. Our approach showed better processing speed and better video quality comparing with traditional error concealment algorithm.

• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.37A no.11
• /
• pp.918-926
• /
• 2012

In 3D video transmission, a depth map being used for depth image based rendering (DIBR) is generally compressed by reducing resolution for coding efficiency. Errors in resolution reduction are recovered by an appropriate up-sampling method after decoding. However, most previous works only focus on up-sampling techniques to reduce errors. In this paper, we propose a novel down-sampling technique of depth map that applies different down-sampling rates on moving objects and background in order to enhance human perceptual quality. Experimental results demonstrate that the proposed scheme provides both higher visual quality and peak signal-to-noise ratio (PSNR). Also, our method is compatible with other up-sampling techniques.

• Journal of the Korea Institute of Information and Communication Engineering
• /
• v.16 no.7
• /
• pp.1406-1415
• /
• 2012

Though WiMedia supports the higher data rates than other WPAN technologies, a WiMedia device cannot reach other devices which are apart from it more than 10 meter; the limited transmission range of the WiMedia protocol. In this paper, we propose a multi-hop QoS routing protocol to enable WiMedia devices to transmit real-time data to devices that is located out of transmission range. The proposed routing protocol is a hybrid routing protocol, which is the mixed protocol of table-driven and on-demand routing algorithm. In the proposed protocol, a route for a device within 2-hop is established by using the table-driven routing algorithm and a route for the device beyond 2-hop is established by using the on-demand routing algorithm. We perform ns-2 simulation to investigate the performance of the proposed routing protocol with AODV and DSDV. The simulation results show that the proposed protocol's performance is better than AODV and DSDV in terms of the throughput and delay.

• Journal of Satellite, Information and Communications
• /
• v.11 no.2
• /
• pp.60-64
• /
• 2016

In this paper, we propose a scheme for MIMO beamforming for the backscatter communication using a multi-tag to improve the efficiency of energy harvesting and the BER of received signals. We obtain a normal channel information through a communication between the H-AP and multi-tag. The H-AP sets parameters for the transmission scenario of the spatial channel model (SCM) using the obtained channel information and generates a SCM channel information. Then, the H-AP transmits signals that have optimal transmission power to increase the signal-to-interference-plus-noise ratio (SINR) to each of tags. Tags perform a backscatter communication with signals. The receiver performs a time switching technique of energy harvesting using backscatter signals from the multi-tag. Simulation results demonstrate effectiveness of the proposed scheme, and the harvesting efficiency and BER at the receiver is greatly improved.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.9 no.5
• /
• pp.589-602
• /
• 1998

While ATM technology results in considerable advantages(less overhead, increased throughput) in an optical networks, It causes severe problems(single and burst error) when ATM is transmitted over an error-prone channel, such as wireless link. In this paper we describe our investigation on ATM over wireless network. we first evaluate performance of ATM data transmission over a wireless link. Secondly we analyze performance improvements of Forward Error Correction(FEC) or ARQ(Automatic Repeat reQuest) scheme applied to wireless ATM link and provide performance comparison between FEC and ARQ through the use of packet error rate and throughput. Lastly we suggest error control architecture to overcome the impact of the bit error characteristics of a wireless link on wireless ATM network.

• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.17 no.2
• /
• pp.168-180
• /
• 1992

Commumication technology has been continuously developed to overcome the distance and time for the transmission of information to the human society. Wireless mobile communication, which had been used mostly in the military and police is widely used these days for enterprise and individuals. Therefore the domestic usage of the advanced mobile phone service are progressively gaining wide popularity. The modulation techniques used usually in mobile communications were the analog techniques such as AM and FM, but they are getting replaced by the digital techniques, However, the major disadvantage of the digital communications is the increase of the transmission bandwidth. Therefore, it is very important to use efficiently the limited frequency bandwidth. The domestic research and development on the subject seems quite limited and in order to establish the technology of the digital mobile communications. This thesis presents the design of the frequency hopping synthesizer providing 124 channels with a channel spcing of 200KHz. VCD used in the synthesizer employs a semi-rigid cable for higher purity of signal spectrum, and a hybrid pgase detector is realized with a sample hold phase detector in conjuction with a tri-state phase detedctor.

• ETRI Journal
• /
• v.38 no.5
• /
• pp.981-987
• /
• 2016

We present a cost-effective dual polarization quadrature phase-shift coherent receiver module using a silica planar lightwave circuit (PLC) hybrid assembly. Two polarization beam splitters and two $90^{\circ}$ optical hybrids are monolithically integrated in one silica PLC chip with an index contrast of $2%-{\Delta}$. Two four-channel spot-size converter integrated waveguide-photodetector (PD) arrays are bonded on PD carriers for transverse-electric/transverse-magnetic polarization, and butt-coupled to a polished facet of the PLC using a simple chip-to-chip bonding method. Instead of a ceramic sub-mount, a low-cost printed circuit board is applied in the module. A stepped CuW block is used to dissipate the heat generated from trans-impedance amplifiers and to vertically align RF transmission lines. The fabricated coherent receiver shows a 3-dB bandwidth of 26 GHz and a common mode rejection ratio of 16 dB at 22 GHz for a local oscillator optical input. A bit error rate of $8.3{\times}10^{-11}$ is achieved at a 112-Gbps back-to-back transmission with off-line digital signal processing.

• KSII Transactions on Internet and Information Systems (TIIS)
• /
• v.13 no.2
• /
• pp.962-977
• /
• 2019

The human voice is a convenient method of information transfer between different objects such as between men, men and machine, between machines. The development of information and communication technology, the voice has been able to transfer farther than before. The way to communicate, it is to convert the voice to another form, transmit it, and then reconvert it back to sound. In such a communication process, a vocoder is a method of converting and re-converting a voice and sound. The CELP (Code-Excited Linear Prediction) type vocoder, one of the voice codecs, is adapted as a standard codec since it provides high quality sound even though its transmission speed is relatively low. The EVRC (Enhanced Variable Rate CODEC) and QCELP (Qualcomm Code-Excited Linear Prediction), variable bit rate vocoders, are used for mobile phones in 3G environment. For the real-time implementation of a vocoder, the reduction of sound quality is a typical problem. To improve the sound quality, that is important to know the size and shape of noise. In the existing sound quality improvement method, the voice activated is detected or used, or statistical methods are used by the large mount of data. However, there is a disadvantage in that no noise can be detected, when there is a continuous signal or when a change in noise is large.This paper focused on finding a better way to decrease the reduction of sound quality in lower bit transmission environments. Based on simulation results, this study proposed a preprocessor application that estimates the SNR (Signal to Noise Ratio) using the spectral SNR estimation method. The SNR estimation method adopted the IMBE (Improved Multi-Band Excitation) instead of using the SNR, which is a continuous speech signal. Finally, this application improves the quality of the vocoder by enhancing sound quality adaptively.