• Journal of Adhesion and Interface
• /
• v.7 no.4
• /
• pp.32-38
• /
• 2006

A series of organic-inorganic hybrids, PCL/EP/$SiO_2$, involving epoxy resin and triethoxysilane-terminated polycaprolactone elastomer (PCL-TESi) were prepared via polymerization of diglycidyl ether of bisphenol A (DGEBA) with amine curing agent KB-2 and sol-gel process of PCL-TESi. The curing reactions were started from the initially homogeneous mixture of DGEBA, KB-2 and the PCL-TESi. The organicinorganic hybrids containing up to 4.95% (wt) of $SiO_2$ were obtained and characterized by FT-IR, transmission electron microscopy (TEM), differential scanning calorimetry (DSC) and thermogravimetry analysis (TGA). It was experimentally shown that the swelling property in toluene, morphologies and thermal properties of the resulting hybrids were quite dependent on the contents of $SiO_2$. The crosslink network density decreases with increasing of the PCL-TESi. And in TEM, the phase separated morphology of these hybrids was found, which resulted from the coagulation of Si-O-Si networks resulting from $-Si(OC_2H_5)_3$ of PCL-TESi self-curing by hydrolytic silanol condensation, with the advancement of the curing reaction in the modified epoxy resin systems. Meanwhile, the change of the $SiO_2$ content made the morphologies changed from aggregated particles of Si-O-Si in the hybrid to nanocluster of interconnected Si-O-Si particles, then to aggregated Si-O-Si dispersing in the continuous cured epoxy phase again, and last to co-continuous interpenetrating network. The glass transition behavior of the hybrid material was cooperative motion of large chain segments, which were hindered by the inorganic Si-O-Si network. And in TG analysis, the characteristic temperature at 5% of weight loss was evidently increased from $120.5^{\circ}C$ of pure cured epoxy to $277.6^{\circ}C$ of 3.84% (wt) of $SiO_2$ modified epoxy due to the existence of Si-O-Si when PCL-TESi was added in the hybrid.

• Polymer(Korea)
• /
• v.38 no.2
• /
• pp.232-239
• /
• 2014

Poly(lactic acid)(PLA) nanocomposites containing various nanofillers were synthesized using the solution intercalation method. Organically modified bentonite clay (NSE), octadecylamine-graphene oxide (ODA-GO), and an NSE/ODA-GO complex were utilized as nanofillers in the fabrication of PLA hybrid films. PLA hybrid films with varying nanofiller contents in the range of 0-10 wt% were examined and compared in terms of their thermomechanical properties, morphologies, and oxygen permeabilities. Transmission electron microscopy (TEM) confirmed that most of the NSE and ODA-GO nanofillers were dispersed homogeneously throughout the PLA matrix on the nanoscale, although some agglomerate NSE/ODA-GO complex particles were also formed. Among the three nanofillers for PLA hybrid films, the NSE/ODA-GO complex showed the best improvement in film thermal stability. In contrast, NSE and ODA-GO exhibited the best improvement in tensile mechanical properties and oxygen barrier properties of the PLA hybrid films, respectively.

• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.34 no.9C
• /
• pp.906-914
• /
• 2009

SC-FDMA is employed in the 3GPP-LTE standard as the uplink transmission scheme. SC-FDMA has advantages that the signal has a low PAPR property and a simple equalizer such as FD-LE can be implemented. But FD-LE has inferior performance to Hybrid-DFE composed of frequency-domain feedforward filter and time-domain feedback filter. Recently, several IB-DFE algorithms have been proposed to overcome the disadvantages of implementation and processing complexity of Hybrid-DFE and to obtain superior performance to FD-LE. In this paper, we apply several IB-DFE algorithms to 3GPP-LTE uplink system and compare their performance by calculating BER. We investigate the effects of channel estimation errors and Doppler shift on performance. Finally, by analyzing computational complexity of IB-DFEs, we present some criteria to choose appropriate algorithm and to decide the number of iterative processes.

• Journal of the Korea Institute of Information and Communication Engineering
• /
• v.16 no.5
• /
• pp.1023-1028
• /
• 2012

A MMIC (Monolithic Microwave Integrated Circuit) mixer chip using the Schottky diode of an GaAs p-HEMT process has been developed for the I/Q demodulator of non-contact near field microwave probing system. A single balanced mixer type is adopted to achieve simple structure of the I/Q demodulator. A quadrature hybrid coupler and a quarter wavelength transmission line for 180 degree hybrid are realized with lumped elements of MIM capacitor and spiral inductor to reduce the mixer chip size. According to the on-wafer measurement, this MMIC mixer covers RF and LO frequencies of 1650MHz to 2050MHz with flat conversion loss. The MMIC mixer with miniature size of $2.5mm{\times}1.7mm$ demonstrates conversion loss below 12dB for both variations of RF and LO frequencies, LO-to-IF isolation above 43dB and RF-to-IF isolation above 23dB, respectively.

• Journal of the Korea Institute of Information and Communication Engineering
• /
• v.19 no.2
• /
• pp.471-476
• /
• 2015

In this paper, we propose an energy efficient hybrid MAC protocol for multi-hop wireless sensor networks. The proposed MAC protocol used a hybrid mechanism, in which contention-based MAC protocol and contention free MAC protocol are combined. The sensor nodes located far from the sink node usually send few data packet since they try to send measured data by themselves. So contention-based MAC protocol is useful among them. But other nodes located near sink node usually have lots of data packets since they plays as a relay node. Contention-based MAC protocol among them is not suitable. Using contention-based MAC protocol in heavy data traffic environment, packet collisions and transmission delay may increase. In this paper, slot assignment between sender nodes by sink node is used. The proposed mechanism is efficient in energy and latency. Results showed that our MAC protocol outperformed other protocol in terms of data packet delivery delay and energy consumption.

• The Journal of the Korea institute of electronic communication sciences
• /
• v.13 no.6
• /
• pp.1235-1242
• /
• 2018

When the wind speed changes rapidly, the wind turbine is stopped for the safety of the power system and the mechanical system. At that moment, the wind turbine gearbox is damaged and broken due to the contact load of the gearbox. In addition, the problems such as increasing frictional heat and deteriorate of the brake occur, because the power of the blades is transmitted directly to the brakes. This paper proposes a hybrid magnetic gear shape that solves the problem caused by the contact of the mechanical gear, which is the power transmission device of the wind power generation system, and the power cutoff system. The shape of the hybrid magnetic gearsuitable for the wind power generation system is derived through the torque and loss analysis according to the shape of the hybrid magnetic gear by using the two dimensional finite analysis method.

• Journal of KIISE:Computer Systems and Theory
• /
• v.33 no.9
• /
• pp.691-698
• /
• 2006

TCP/IP Offload Engine (TOE) is a technology that processes TCP/IP on a network adapter instead of a host CPU to reduce protocol processing overhead from the host CPU. There have been some approaches to implementing TOE: software TOE based on an embedded processor; hardware TOE based on ASIC implementation; and hybrid TOE in which software and hardware functions are combined. In this paper, we designed software modules and hardware modules for a hybrid TOE on an FPGA that had two processor cores. Software modules are based on the embedded Linux. Hardware modules are for data transmission (TX) and reception (RX). One core controls the TX path and the other controls the RX path of the Linux. This TX/RX path separation mechanism can reduce task switching overheads between processes and overcome poor performance of single embedded processor. Hardware modules deal with creating headers for outgoing packets, processing headers of incoming packets, and fetching or storing data from or to the host memory by DMA. These can make it possible to improve the performance of data transmission and reception. We proved performance of the TOE with separated transmission and reception paths by performing experiments with a TOE network adapter that was equipped with the FPGA having processor cores.

• Journal of Broadcast Engineering
• /
• v.10 no.1 s.26
• /
• pp.14-21
• /
• 2005

This paper described an Enhanced-xVSB system for improving mobile/pedestrian reception performance to the ATSC(Advanced Television System Committee) DTV 8-VSB transmission standard. E-xVSB system can transmit a mixture of normal (8-VSB) stream and enhanced (robust) stream. The robust stream has a higher threshold of visibility (TOV) compared to the standard stream, and legacy receivers ignore the robust packets. Thus, Enhanced-xVSB system is fully backward compatible with a current ATSC standard. For mobile and portable reception support, E-xVSB system adopts a reduced constellation methodas well as enhanced trellis-coded modulation scheme. E-xVSB system supports a variety of enhanced modulation schemes : Pseudo-2VSB, Enhanced-4VSB, modified Enhanced-8VSB and Hybrid-VSB. Proposed E-xVSB system performs well under serious dynamic multipath reception environment.

• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.34 no.8A
• /
• pp.610-617
• /
• 2009

This paper proposes a cross-layer design combining adaptive modulation and coding (AMC) with truncated hybrid automatic repeat request (HARQ) for wireless multicast transmission, in order to increase the spectral efficiency while meeting the target quality-of-service (QoS). In the design, we provide the selection criterion of AMC so as to satisfy the target packet error rate (PER) of all users when the multicast data is received through the common channel and the number of retransmission is limited by the delay constraint of the service. The analytically derived results show that the cross-layer design using HARQ provides a better spectral efficiency than the AMC without HARQ by allowing retransmission and code combining. It is also observed that the design for multicast outperforms that for unicast in the mid to high signal-to-noise ratio region.

• The KIPS Transactions:PartC
• /
• v.10C no.1
• /
• pp.77-86
• /
• 2003

This paper describes the new method for Internet multicast routing protocols using MPLS (Multiprotocol Label Switching) networks. Internet multicast routing protocols are divided into three categories in terms if tree types and tree characteristics : a shortest path tree a shared tree and hybrid tree types. MPLS should support various multicast mechanisms because of extremely different IP multicast architectures, such as uni-/bi-directional link, Flooding/prune tree maintenance mechanism. the existence of different tree types with the same group, etc. There are so many problems over MPLS multicast that the solutions can't be easily figured out. In this Paper, we make a few assumptions on which the solutions of IP multicast routing protocols over MPLS networks are given. A broadcasting label is defined for the shortest path tree types. Cell interleaving problems of the shared tree types is solved by using block-based transmission mechanism. Finally, the existing hybrid-type multicast routing protocol is reasonably modified Shortest Path tree type to support MPLS multicast. It has been shown that these modifications give better performance (transmission delay) than the orignal method.