Research about hybrid solar air-water heater that can make heated air and hot water was conducted as a part of improving efficiency of solar thermal energy. At this experiment, ability of making heating air and hot water was investigated and compared with traditional solar air heater and flat plate solar collector for hot water when air or liquid was heated respectively. Comparing hybrid solar air-water heater that used in this experiment to other solar air heater studied already, it has a lower efficiency at same mass flow rate. Air channel structure, fin's shape and arrangement in the air channel result in these difference then the ability of air heating need to be improved with changing these thing. In case of making hot water, performance was shown as similar with traditional system although the air channels were established beneath absorbing plate. But the heat loss coefficient was shown higher value by installing of air channel. Also the performance of hot water making was shown lower value at same liquid mass flow rate with traditional flat plate solar collector for hot water. So the necessity of performance improvement at lower mass flow rate of each heating medium can be confirmed.
VOD 시스템에서 비디오 서버가 지원할 수 있는 채널의 개수는 서버의 통신 대역폭에 의해 결정되므로 비디오 서버의 가용채널 수는 제한되어 있다. 멀티캐스트 데이터를 공유함으로써 비디오 서버의 네트워크 입출력 대역폭을 절감하기 위해 일괄처리, 패칭, 배치-패칭과 같은 멀티캐스트 방법들이 제안되 었다. 본 논문에서는 인기 비디오 요청들에 대해 먼저 배칭 방법을 적용한 후 배치들에 대해 패칭 방법을 수행하는 채널 예약 배치-패칭 방법을 제안한다. 그리고 제안하는 방법은 많은 인기 비디오 요청을 위하여 비디오 서버의 채널 용량 중 일부를 예약하므로 인기 비디오 요청들을 이탈없이 서비스할 수 있다. 제안하는 방법의 성능을 시뮬레이션을 통하여 평균 서비스 지연 시간, 이탈율, 공평성, 프레임 절감율 항목에 대해 패칭 방법과 배치-패칭 방법의 성능과 비교한다.
현재 대부분의 집적회로는 bulk CMOS 기술을 사용해서 제작되고 있으나 전력 소모를 낮추고 die 크기를 줄이기에는 한계점에 도달해있다. 이러한 어려움을 획기적으로 극복할 수 있는 초저전력 기술로서 SOI CMOS 기술이 최근에 크게 각광을 받고 있다. 본 논문에서는 100 nm Thin SOI 기판 위에 제작된 n-채널 MOSFET 소자들의 열전자 효과들의 온도 의존성에 관한 연구 결과들이 논의되었다. 소자들이 LDD 구조를 갖고 있음에도 불구하고 열전자 효과들이 예상보다 더 심각한 것으로 나타났는데, 이는 채널과 기판 접지 사이의 직렬 저항이 크기 때문인 것으로 믿어졌다. 온도가 높을수록 채널에서의 phonon scattering의 증가와 함께 열전자 효과는 감소하였는데, 이는 phonon scattering의 증가는 결과적으로 열전자의 생성을 감소시켰기 때문인 것으로 판단된다.
Hot carrier effects as a function of bias stress time and bias stress conditions were syste-matica1ly investigated in p-channel po1y-Si TFT's fabricated on the quartz substrate. The device degradation was observed for the negative bias stress. After positive bias stressing, Improvement of electrical characteristic except for subthreshold slope was observed. It was found that these results were related to the hot carrier injection into the gate oxide and interface states at the poly-Si/SiO$_2$interface rather than defects states generation under bias stress.
Researchers have recently begun to study hot stamping processes to shorten the mold cooling time and improve productivity. These publications explain that the mold cooling time can be reduced by using a curved cooling channel, where the mold surface is processed to a uniform depth, instead of a straight cooling channel that uses the conventional gun drilling machine. This study investigates the characteristics of the front pillar of an automobile after using a mold with a curved cooling channel. To analyze the change in properties, we used a 1.6 mm boron steel blank and heated the prototype at $930^{\circ}C$ for 5 minutes. Next, we formed the prototype with a load of about 500 tons while varying the mold cooling time between 1 and 10 seconds. We subjected each prototype specimen to a tensile strength test, a hardness test, and a tissue surface observation.
Transactions on Electrical and Electronic Materials
/
제11권1호
/
pp.15-19
/
2010
In this paper, we discuss design considerations for an n-channel metal-oxide-semiconductor field-effect transistor (MOSFET) with a lateral asymmetric channel (LAC) doping profile. We employed a $0.35\;{\mu}m$ standard complementary MOSFET process for fabrication of the devices. The gates to the LAC doping overlap lengths were 0.5, 1.0, and $1.5\;{\mu}m$. The drain current ($I_{ON}$), transconductance ($g_m$), substrate current ($i_{SUB}$), drain to source leakage current ($i_{OFF}$), and channel-hot-electron (CHE) reliability characteristics were taken into account for optimum device design. The LAC devices with shorter overlap lengths demonstrated improved $I_{ON}$ and $g_m$ characteristics. On the other hand, the LAC devices with longer overlap lengths demonstrated improved CHE degradation and $I_{OFF}$ characteristics.
In this paper, we have fabricated the hydrogenated n-channel polysilicon thin film transistor (TFT) with LDD structure and have analyzed the hot carrier degradation characteristics by electrical stress. We have compared the threshold voltage (Vth), sub-threshold slope (S), and trans-conductance (Gm) for devices with LDD (Lightly Doped Drain) structure and non-LDD at same active sizes. We have analyzed the hot carrier effects by the hydrogenation in devices. As a analyzed results, the threshold voltage, sub-threshold slope for n-channel poly-si TFT were increased, trans-conductance was decreased. The effects of hydrogenation in n-channel poly-si TFT with LDD structure were shown the lower variations of characteristics than devices of the non-LDD structure with nomal process.
This paper reports the studies of the inversion layer mobility in p-channel Si MOSFET's under hot-carrier degradated condition. The validity of relationship of hot carrier degradations between the surface effective mobility and field effect mobility and are examined. The effective mobility(${\mu}$$\_$eff/) is derived from the channel conductances, while the field-effect mobility(${\mu}$$\_$FE/) is obtained from the transconductance. The characteristics of mobility curves can be divided into the 3 parts of curves. It was reported that the mobility degradation is due to phonon scattering, coulombic scattering and surface roughness. We are measured the mobility slope in curves with DC-stress [V$\_$g/=-3.1v]. It was found that the mobility(${\mu}$$\_$eff/ and ${\mu}$$\_$FE/) of p-MOSFET's was increased by increasing stress time and decreasing channel length. Because of the increasing stress time and increasing V$\_$g/ is changed oxide reliability and increased vertical field.
Deep Submicron 영역에서 요구되는 고성능 소자로서 자기-정렬된 ESD(Elevated Source/Drain)구조의 MOSFET을 제안하였다. 제안된 ESD 구조는 일반적인 LDD(Lightly-Doped Drain)구조와는 달리 한번의 소오스/드레인 이온주입 과정이 필요하며, 건식 식각 방법을 적용하여 채널의 함몰 깊이를 조정할 수 있는 구조를 갖는다. 또한 제거가 가능한 질화막 측벽을 최종 질화막 측벽의 형성 이전에 선택적인 채널 이온주입을 위한 마스크로 활용하여 hot-carrier 현상을 감소시켰으며, 반전된 질화막 측벽을 사용하여 기존이 ESD 구조에서 문제시될 수 있는 자기-정렬의 문제를 해결하였다. 시뮬레이션 결과, 채널의 함몰 깊이 및 측벽의 넓이를 조정함으로써 충격이온화율(ⅠSUB/ID) 및 DIBL(Drain Induced Barrier Lowering) 현상을 효과적으로 감소시킬 수 있고, 유효채널 길이에 따라 차이가 있으나 두 번의 질화막 측벽을 사용함으로써 hot-carrier 현상이 개선될 수 있음을 확인하였다.
Park, Jinsu;Showdhury, Sanchari;Yoon, Geonju;Kim, Jaemin;Kwon, Keewon;Bae, Sangwoo;Kim, Jinseok;Yi, Junsin
한국전기전자재료학회논문지
/
제33권3호
/
pp.169-172
/
2020
In this paper, the effect of hot carrier injection on an n-bulk fin field-effect transistor (FinFET) is analyzed. The hot carrier injection method is applied to determine the performance change after injection in two ways, channel hot electron (CHE) and drain avalanche hot carrier (DAHC), which have the greatest effect at room temperature. The optimum condition for CHE injection is VG=VD, and the optimal condition for DAHC injection can be indirectly confirmed by measuring the peak value of the substrate current. Deterioration by DAHC injection affects not only hot electrons formed by impact ionization, but also hot holes, which has a greater impact on reliability than CHE. Further, we test the amount of drain voltage that can be withstood, and extracted the lifetime of the device. Under CHE injection conditions, the drain voltage was able to maintain a lifetime of more than 10 years at a maximum of 1.25 V, while DAHC was able to achieve a lifetime exceeding 10 years at a 1.05-V drain voltage, which is 0.2 V lower than that of CHE injection conditions.
본 웹사이트에 게시된 이메일 주소가 전자우편 수집 프로그램이나
그 밖의 기술적 장치를 이용하여 무단으로 수집되는 것을 거부하며,
이를 위반시 정보통신망법에 의해 형사 처벌됨을 유념하시기 바랍니다.
[게시일 2004년 10월 1일]
이용약관
제 1 장 총칙
제 1 조 (목적)
이 이용약관은 KoreaScience 홈페이지(이하 “당 사이트”)에서 제공하는 인터넷 서비스(이하 '서비스')의 가입조건 및 이용에 관한 제반 사항과 기타 필요한 사항을 구체적으로 규정함을 목적으로 합니다.
제 2 조 (용어의 정의)
① "이용자"라 함은 당 사이트에 접속하여 이 약관에 따라 당 사이트가 제공하는 서비스를 받는 회원 및 비회원을
말합니다.
② "회원"이라 함은 서비스를 이용하기 위하여 당 사이트에 개인정보를 제공하여 아이디(ID)와 비밀번호를 부여
받은 자를 말합니다.
③ "회원 아이디(ID)"라 함은 회원의 식별 및 서비스 이용을 위하여 자신이 선정한 문자 및 숫자의 조합을
말합니다.
④ "비밀번호(패스워드)"라 함은 회원이 자신의 비밀보호를 위하여 선정한 문자 및 숫자의 조합을 말합니다.
제 3 조 (이용약관의 효력 및 변경)
① 이 약관은 당 사이트에 게시하거나 기타의 방법으로 회원에게 공지함으로써 효력이 발생합니다.
② 당 사이트는 이 약관을 개정할 경우에 적용일자 및 개정사유를 명시하여 현행 약관과 함께 당 사이트의
초기화면에 그 적용일자 7일 이전부터 적용일자 전일까지 공지합니다. 다만, 회원에게 불리하게 약관내용을
변경하는 경우에는 최소한 30일 이상의 사전 유예기간을 두고 공지합니다. 이 경우 당 사이트는 개정 전
내용과 개정 후 내용을 명확하게 비교하여 이용자가 알기 쉽도록 표시합니다.
제 4 조(약관 외 준칙)
① 이 약관은 당 사이트가 제공하는 서비스에 관한 이용안내와 함께 적용됩니다.
② 이 약관에 명시되지 아니한 사항은 관계법령의 규정이 적용됩니다.
제 2 장 이용계약의 체결
제 5 조 (이용계약의 성립 등)
① 이용계약은 이용고객이 당 사이트가 정한 약관에 「동의합니다」를 선택하고, 당 사이트가 정한
온라인신청양식을 작성하여 서비스 이용을 신청한 후, 당 사이트가 이를 승낙함으로써 성립합니다.
② 제1항의 승낙은 당 사이트가 제공하는 과학기술정보검색, 맞춤정보, 서지정보 등 다른 서비스의 이용승낙을
포함합니다.
제 6 조 (회원가입)
서비스를 이용하고자 하는 고객은 당 사이트에서 정한 회원가입양식에 개인정보를 기재하여 가입을 하여야 합니다.
제 7 조 (개인정보의 보호 및 사용)
당 사이트는 관계법령이 정하는 바에 따라 회원 등록정보를 포함한 회원의 개인정보를 보호하기 위해 노력합니다. 회원 개인정보의 보호 및 사용에 대해서는 관련법령 및 당 사이트의 개인정보 보호정책이 적용됩니다.
제 8 조 (이용 신청의 승낙과 제한)
① 당 사이트는 제6조의 규정에 의한 이용신청고객에 대하여 서비스 이용을 승낙합니다.
② 당 사이트는 아래사항에 해당하는 경우에 대해서 승낙하지 아니 합니다.
- 이용계약 신청서의 내용을 허위로 기재한 경우
- 기타 규정한 제반사항을 위반하며 신청하는 경우
제 9 조 (회원 ID 부여 및 변경 등)
① 당 사이트는 이용고객에 대하여 약관에 정하는 바에 따라 자신이 선정한 회원 ID를 부여합니다.
② 회원 ID는 원칙적으로 변경이 불가하며 부득이한 사유로 인하여 변경 하고자 하는 경우에는 해당 ID를
해지하고 재가입해야 합니다.
③ 기타 회원 개인정보 관리 및 변경 등에 관한 사항은 서비스별 안내에 정하는 바에 의합니다.
제 3 장 계약 당사자의 의무
제 10 조 (KISTI의 의무)
① 당 사이트는 이용고객이 희망한 서비스 제공 개시일에 특별한 사정이 없는 한 서비스를 이용할 수 있도록
하여야 합니다.
② 당 사이트는 개인정보 보호를 위해 보안시스템을 구축하며 개인정보 보호정책을 공시하고 준수합니다.
③ 당 사이트는 회원으로부터 제기되는 의견이나 불만이 정당하다고 객관적으로 인정될 경우에는 적절한 절차를
거쳐 즉시 처리하여야 합니다. 다만, 즉시 처리가 곤란한 경우는 회원에게 그 사유와 처리일정을 통보하여야
합니다.
제 11 조 (회원의 의무)
① 이용자는 회원가입 신청 또는 회원정보 변경 시 실명으로 모든 사항을 사실에 근거하여 작성하여야 하며,
허위 또는 타인의 정보를 등록할 경우 일체의 권리를 주장할 수 없습니다.
② 당 사이트가 관계법령 및 개인정보 보호정책에 의거하여 그 책임을 지는 경우를 제외하고 회원에게 부여된
ID의 비밀번호 관리소홀, 부정사용에 의하여 발생하는 모든 결과에 대한 책임은 회원에게 있습니다.
③ 회원은 당 사이트 및 제 3자의 지적 재산권을 침해해서는 안 됩니다.
제 4 장 서비스의 이용
제 12 조 (서비스 이용 시간)
① 서비스 이용은 당 사이트의 업무상 또는 기술상 특별한 지장이 없는 한 연중무휴, 1일 24시간 운영을
원칙으로 합니다. 단, 당 사이트는 시스템 정기점검, 증설 및 교체를 위해 당 사이트가 정한 날이나 시간에
서비스를 일시 중단할 수 있으며, 예정되어 있는 작업으로 인한 서비스 일시중단은 당 사이트 홈페이지를
통해 사전에 공지합니다.
② 당 사이트는 서비스를 특정범위로 분할하여 각 범위별로 이용가능시간을 별도로 지정할 수 있습니다. 다만
이 경우 그 내용을 공지합니다.
제 13 조 (홈페이지 저작권)
① NDSL에서 제공하는 모든 저작물의 저작권은 원저작자에게 있으며, KISTI는 복제/배포/전송권을 확보하고
있습니다.
② NDSL에서 제공하는 콘텐츠를 상업적 및 기타 영리목적으로 복제/배포/전송할 경우 사전에 KISTI의 허락을
받아야 합니다.
③ NDSL에서 제공하는 콘텐츠를 보도, 비평, 교육, 연구 등을 위하여 정당한 범위 안에서 공정한 관행에
합치되게 인용할 수 있습니다.
④ NDSL에서 제공하는 콘텐츠를 무단 복제, 전송, 배포 기타 저작권법에 위반되는 방법으로 이용할 경우
저작권법 제136조에 따라 5년 이하의 징역 또는 5천만 원 이하의 벌금에 처해질 수 있습니다.
제 14 조 (유료서비스)
① 당 사이트 및 협력기관이 정한 유료서비스(원문복사 등)는 별도로 정해진 바에 따르며, 변경사항은 시행 전에
당 사이트 홈페이지를 통하여 회원에게 공지합니다.
② 유료서비스를 이용하려는 회원은 정해진 요금체계에 따라 요금을 납부해야 합니다.
제 5 장 계약 해지 및 이용 제한
제 15 조 (계약 해지)
회원이 이용계약을 해지하고자 하는 때에는 [가입해지] 메뉴를 이용해 직접 해지해야 합니다.
제 16 조 (서비스 이용제한)
① 당 사이트는 회원이 서비스 이용내용에 있어서 본 약관 제 11조 내용을 위반하거나, 다음 각 호에 해당하는
경우 서비스 이용을 제한할 수 있습니다.
- 2년 이상 서비스를 이용한 적이 없는 경우
- 기타 정상적인 서비스 운영에 방해가 될 경우
② 상기 이용제한 규정에 따라 서비스를 이용하는 회원에게 서비스 이용에 대하여 별도 공지 없이 서비스 이용의
일시정지, 이용계약 해지 할 수 있습니다.
제 17 조 (전자우편주소 수집 금지)
회원은 전자우편주소 추출기 등을 이용하여 전자우편주소를 수집 또는 제3자에게 제공할 수 없습니다.
제 6 장 손해배상 및 기타사항
제 18 조 (손해배상)
당 사이트는 무료로 제공되는 서비스와 관련하여 회원에게 어떠한 손해가 발생하더라도 당 사이트가 고의 또는 과실로 인한 손해발생을 제외하고는 이에 대하여 책임을 부담하지 아니합니다.
제 19 조 (관할 법원)
서비스 이용으로 발생한 분쟁에 대해 소송이 제기되는 경우 민사 소송법상의 관할 법원에 제기합니다.
[부 칙]
1. (시행일) 이 약관은 2016년 9월 5일부터 적용되며, 종전 약관은 본 약관으로 대체되며, 개정된 약관의 적용일 이전 가입자도 개정된 약관의 적용을 받습니다.