• Journal of Ceramic Processing Research
• /
• v.13 no.spc1
• /
• pp.6-9
• /
• 2012

Eu3+-doped RE2O3 (RE = Gd, Y and La) phosphors were prepared by solvothermal reaction method and their crystalline structure, phase transformation and surface morphologies were investigated by using X-ray diffraction (XRD), field emission scanning electron microscopy (FE-SEM). The obtained RE2O3:Eu3+ phosphors are nanocrystalline-sized. The luminescence properties of Eu3+ ions in different host materials, namely, Gd2O3, Y2O3 and La2O3 have been investigated. PACS number: 32.50.+d, 78.55.-m, 81.40.Tv.

• Korean Chemical Engineering Research
• /
• v.49 no.3
• /
• pp.325-329
• /
• 2011

$Ir(pmb)_{3}$(Iridium(III)Tri(1-phenyl-3-methylbenzimidazolin-2-ylidene-$C,C^{2'}$ ) was synthesized to develop a deep blue-emitting Ir(III) complex. We suggested the ultrasonic reactor to enhance the poor reaction yield of $Ir(pmb)_{3}$. The ultrasonic wave enhanced the reaction yield of $Ir(pmb)_{3}$ because the ultrasound helped non-soluble reactants disperse efficiently and produced free radial during the reaction. The maximum yield of $Ir(pmb)_{3}$ was 42.5%, which was 4 times higher than conventional method. Organic light emitting devices were fabricated with the synthesized mer-$Ir(pmb)_{3}$ which emitted at 405 nm. A range of host materials with large bandgaps (UGH2, mCP and CBP) were tested for developing a deep blue emitting device. In case of the device with mCP as the host material, it emitted deep blue and performed quite well relative to the other host materials tested.

• Maxillofacial Plastic and Reconstructive Surgery
• /
• v.31 no.3
• /
• pp.207-215
• /
• 2009

Purpose: The aim of the present study is to evaluate the long term bone healing after horizontal ridge augmentation using auto block bone graft for implant installation timing. Materials and Methods: Five Beagle dogs(which were 14 months old and weighted approximately 10kg). In surgery 1(extraction & bone defect), premolars(P2, P3,P4) were extracted and the buccal bone plate was removed to create a horizontally defected ridge. After three months healing, in surgery 2(ridge augmentation). Auto block bone grafts from the mandibular ramus were used in filling the bone defects were fixed with stabilizing screws. The following fluorochrome labels were given intravenously to the beagle dogs: oxytetracycline 1week after the surgery, alizarin red 4 weeks after the surgery, calcein blue 8 weeks after the surgery. The tissue samples were obtained from the sacrificed dogs of 1, 4, 8, 12, 16 weeks after the surgery. Non-decalcified sections were prepared by resin embedding and microsection to find thickness of $10{\mu}m$ for the histologic examination and analysis. Results: 1. We could achieve the successful reconstruction of the horizontal bone defect by auto block bone graft. The grafted bone block remained stable morohologically after 16 weeks of the surgery. 2. In the histologic view. We observed osteoid tissue from the sample $4^{th}$ week sample and active capillary reconstruction in the grafted bone from the $12^{th}$ week sample. Healing procedures of auto bone grafts were compared to that of the host bone. 3. Bone mineralization could be detected from the $8^{th}$ week sample. 4. Fluorochrome labeling showed active bony changes and formation at the interface of the host bone and the block graft mainly. Bony activation in the grafted bone could be seen from the $4^{th}$ week samples. Conclusions: Active bone formation and remodeling between the grafted bone and host bone can be seen through the revascularization. After the perfect adhesion to host bone, Timing of successful implant installation can be detected through the ideal ridge formation by horizontal ridge augmentation.

• Journal of Periodontal and Implant Science
• /
• v.38 no.sup2
• /
• pp.317-324
• /
• 2008

Purpose: Aggregatibacter actinomycetemcomitans was associated with localized aggressive periodontitis, endocarditis, meningitis, and osteomyelitis. The cytolethal distending toxin (CDT) of A. actinomycetemcomitans was considered as a key factor of these diseases is composed of five open reading frames (ORFs). Among of them, An enzymatic subunit of the CDT, CdtB has been known to be internalized into the host cell in order to induce its genotoxic effect. However, CdtB can not be localized in host cytoplasm without the help of a heterodimeric complex consisting of CdtA and CdtC. So, some studies suggested that CdtC functions as a ligand to interact with GM3 ganglioside of host cell surface. The precise role of the CdtC protein in the mechanism of action of the holotoxin is unknown at the present time. The aim of this study was to generate recombinant CdtC proteins expression from A. actinomycetemcomitans, through gene cloning and protein used to investigate the function of Cdt C protein in the bacterial pathogenesis. Materials and Methods: The genomic DNA of A. actinomycetemcomitans Y4 (ATCC29522) was isolated using the genomic DNA extraction kit and used as template to yield cdtC genes by PCR. The amplifed cdtC genes were cloned into T-vector and cloned cdt C gene was then subcloned to pET28a expression vector. The pET28a-cdtC plasmid expressed in BL21 (DE3) Escherichia coli system. Diverse conditons were tested to opitimize the expression and purification of functional CdtC protein in E. coli. Results: In this study we reconstructed CdtC subunit of A. actinomycetemcomitans Y4 and comfirmed the recombinant CdtC expression by SDS-PAGE and Western Blotting. The expression level of the recombinant CdtC was about 2% of total bacterial proteins. Conclusion: The lab condition of procedure for the purification of functionally active recombinant CdtC protein is established. The active recombinant CdtC protein will serve to examine the role of CdtC proteins in the host recognition and enzyme activity of CDT and investigate the pathological process of A. actinomycetemcomitans in periodontal disease.

• Journal of Periodontal and Implant Science
• /
• v.31 no.1
• /
• pp.73-91
• /
• 2001

The present study was performed to compare effects of demineralized freeze-dried bone allograft(DFDBA) with deproteinized bovine bone mineral(DBBM) on periodontal fenestration defect in rats. Twelve adult male rats weighing 500 to 540 grams were used in this study. Periodontal fenestration defects were surgically created with tapered fissure bur(${\Phi}1mm$) at the left side of buccal surface of the mandible. The defect size was from anterior border of the first molar to anterior of the ascending ramus mesiodistally and from just below the alveolar crest to apically 1.5-2mm area apicocoronally with 2mm in depth. Rats were divided into control group, test group I and II. Four defects were assigned to the test group I grafted with DBBM and other 4 defects were assigned to the test group II grafted with DFDBA. The rest of defects were the negative control group. At 10 days and 35 days after surgery, 12 rats were sacrificed through intracardiac perfusion and specimens were obtained prepared with Hematoxylin-Eosin stain for light microscopic evaluation. The results of this study were as follows : 1. In the control group, new bone, osteoid, dense connective tissue were observed in the defects at 10 days. new bone formation was not found but loose connective tissue was formed in the defect and fibrous encapsulation of graft materials was shown in two test groups at 10 days. 2. In all groups, new bone formation was shown in the defect at 35 days. And in the control group, bone formation increased at 35 days than at 10 days. 3. In the test group I and II at 35 days, graft materials were combined with new bone and joined host bone. There was very close contact between new bone, graft materials, and host bone with no gaps. 4. In the test group I and II, new bone formation was similar to that in the control group but not exeeded. In conclusion, in the test group I new bone formation was similar to that in the test group II at 35 days, but there was infiltration of inflammatory cells at 10 days. DFDBA and DBBM were considered as the biocompatible graft materials and effective in the regeneration of new bone.

• Korean Journal of Materials Research
• /
• v.14 no.9
• /
• pp.627-633
• /
• 2004

Lithium titanate whiske($Li_{x}Ti_{4}O_9$) was prepared by an ion-exchange reaction. To this end, the initial material, potassium tetratitanate ($K_{2}Ti_{4}O_9{\cdot}nH_{2}O$) was prepared by calcination of a mixture of $K_{2}CO_3\;and\;TiO_2$ with a molar ratio of 2.8 at $1050^{\circ}C$ for 3 h, followed by boiling water treatment of the calcined products for 10 h. Fibrous potassium tetratitanate could be transformed into layered hydrous titanium dioxide ($H_{2}Ti_{4}O_9{\cdot}nH_{2}O$) through an exchange of $K^{+}\;with\;H^{+}$ using 0.075 M HCl. Also, lithium titanate whisker was finally prepared as $Li^{+}\;and\;H^{+}$ ions were exchanged by adding 20 mL of a mixture solution of LiOH and $LiNO_3$ to 1g whisker and stirring for $5\~15$ days. The average length and diameter of the $Li_{x}Ti_{4}O_9$ whiskers were $10\~20{\mu}m\;and\;1\~3{\mu}m$, respectively.

• Bulletin of the Korean Chemical Society
• /
• v.35 no.6
• /
• pp.1670-1674
• /
• 2014

Two red emitters, 2-(7-(4-(diphenylamino)styryl)-2-methyl-4H-chromen-4-ylidene)malonitrile (Red 1) and 2-(7-(julolidylvinyl)-2-methyl-4H-chromen-4-ylidene)malonitrile (Red 2) have been designed and synthesized for application as red-light emitters in organic light emitting diodes (OLEDs). In these red emitters, the julolidine and triphenyl moieties were introduced to the emitting core as electron donors, and the chrome-derived electron accepting groups such as 2-methyl-(4H-chromen-4-ylidene)malononitrile were connected to electron donating moieties by vinyl groups. To explore the electroluminescence properties of these materials, multilayered OLEDs using red materials (Red 1 and Red 2) as dopants in $Alq_3$ host were fabricated. In particular, a device using Red 1 as the dopant material showed maximum luminous efficiencies and power efficiencies of 0.82 cd/A and 0.33 lm/W at $20mA/cm^2$. Also, a device using Red 2 as a dopant material presented the CIEx,y coordinates of (0.67, 0.32) at 7.0 V.

• 한국정보디스플레이학회:학술대회논문집
• /
• 2006.08a
• /
• pp.1360-1363
• /
• 2006

A borate compound was adopted as new host material for $EU^{3+}$ activator. The $Eu^{3+}-doped\;YCa_3(GaO)_3(BO_3)_4$ (YCGB) phosphors were successfully synthesized. Also, their photoluminescence properties under the excitation of UV ray were measured. In the XRD patterns of the synthesized powders, most peaks were well-matched to a gaudefroyite phase. The emission of $Eu^{3+}$ in YCGB consists of a strong peak centered at 622 nm, which is attributed to $^5D_O-^7F_2$ transition of $Eu^{3+}$ and several weak peaks at near the wavelength. Optimum $Eu^{3+}$ concentration of the red phosphor under the excitation with the wavelength of 395 nm was about 75 mol%. This indicates that the red phosphor has a relatively higher critical concentration than that of the other $Eu^{3+}-doped$ phosphors. The dominant interaction character of $Eu^{3+}$ might be dipole-dipole interaction.

• Textile Coloration and Finishing
• /
• v.19 no.2
• /
• pp.32-35
• /
• 2007

Cyclodextrin is a cyclic oligosaccharid material which shows an ability to incorporate organic guest molecules inside their cavity area. Thus, this ${\beta}-cyclodextrin$ treatment on fiber substrates may provide the changed surface characteristics of the substrates such as solubility, chemical reactivity and spectral property. In this context, the aim of this present work is to make a bridge connection using hetero-bi-functional reactive dye between fiber substrates and ${\beta}-cyclodextrin$. In addition, the corresponding Berberine inclusion behaviors into the inner cavity of ${\beta}-cyclodextrin$ was examined. The %exhaustion of Berberine inclusion as a guest molecule within the ${\beta}-cyclodextrin$ was measured using UV-Vis spectrophotometer. The findings showed that the %exhaustion of Berberine inclusion increased with increasing the prepared dye bridge compound and ${\beta}-cyclodextrin$ host material.

• Biotechnology and Bioprocess Engineering:BBE
• /
• v.7 no.1
• /
• pp.52-55
• /
• 2002

Flow cytometric techniques were used to investigate cell size, protein content and cell cycle behavior of recombinant Saccharomyces cerevisiae strains producing human lysozyme (HLZ). Two different signal sequences, the native yeast $MF\alpha1$ signal sequence and the rat $\alpha-amylase$ signal sequence, were used for secretion of HLZ. The strain containing the rat $\alpha-amylase$ signal sequence showed a higher level of internal lysozyme and lower specific growth rates. Flow cytometric analysis of the total protein content and cell size showed the strain harboring the native yeast signal sequence had a higher total protein content than the strain containing the rat $\alpha-amylase$ signal sequence. Cell cycle analysis indicated that the two lysozyme producing recombinant strains had an increased number of cells in the $G_2+M$ phase of the yeast cell cycle compared with the host strain SEY2102.