• 터널과지하공간
• /
• 제32권3호
• /
• pp.219-230
• /
• 2022

GREAT 셀은 실험실에서 심부지층의 열-수리-역학적 조건을 구현하기 위해 설계된 시험장비로서, 시료 길이방향 축을 중심으로 회전하는 측면의 가압장치를 이용하여 다축 응력장을 생성할 수 있고 균열이 포함된 시료에 대해 유체유동 실험이 가능하다. 본 연구에서는 GREAT 셀을 이용한 삼축압축시험을 수치 해석적으로 모사하고 시료 측면에 작용하는 구속압 조건에 따른 역학적 거동을 분석하였다. 균열이 없는 고분자 재질의 시료에 대한 삼축압축시험 사례를 수치모사하여 실험결과와 비교하였다. 수평 구속압의 균등 및 불균등 조건에서 시료 표면의 변형률(원주변형률)을 분석하였으며, 실험결과와 유사한 경향을 보이는 것으로 검토되었다. 추가로 균열이 포함된 가상의 시료모델을 구성하여 균열면의 마찰 특성 및 형상이 시료 변형에 미치는 영향을 조사하였다.

• 대한기계학회논문집B
• /
• 제33권6호
• /
• pp.435-442
• /
• 2009

Three-dimensional heat transfer characteristics for natural convection flows are numerically investigated in the doubly-inclined cubical-cavity according to the variation of a newly defined orientation angle �� of the hot wall surface from horizontal plane at moderate Rayleigh numbers. Numerical simulations of laminar flows are conducted in the range of Rayleigh numbers($10^4{\leq}Ra{\leq}10^5$) and $0^{\circ}{\leq}{\alpha}90^{circ}$ with a solution code(PowerCFD) employing unstructured cell-centered method. Comparisons of the average Nusselt number at the cold face are made with benchmark solutions and experimental results found in the literature. It is found that the average Nusselt number at the cold wall has a maximum value around the specified orientation ${\alpha}$ at each Rayleigh number. Special attention is also paid to three-dimensional thermal characteristics in natural convection according to new orientation angles at Ra��= $1{\times}10^5$, in order to investigate a new additional heat transfer characteristic found in the range of above Ra = $6{\times}10^4$.

• 대한방사선기술학회지:방사선기술과학
• /
• 제14권1호
• /
• pp.61-72
• /
• 1991

In this paper, the rotating plate method extracting signal and reconstructing original image was proposed. The rotating methode has cell detector array each of which has used in the medical diagnosis X-ray photography. The major problem using the simple horizontal moving or non-moving methode is the size and number of detector cells which have the considerable affection on the sharpness and resolution of the reconstructed image. Secondary, the estimated pixel values of non-detected real points which are placed between detector cells will be the distorted pixels in the reconstructed image. Therefore, the proposed rotating plate method has the exact distribution on the uncertain pixels which were reconstructed by conventional methods to solve there problems. And then, the image using the rotated plate's cell out put signal was reconstructed on the computer simulation. The method will rotated the detector array plate to solve the reconstruction from the detector size and number of conventional methods. The result of simulation has estimated the original pixel position and 81 pixel/mm resolution which the reconsiderlation of the detector's moving orientation, the proposed method has 25 pixel/mm resolution. These results have been represented by 3-D computer graphics.

• 대한기계학회논문집B
• /
• 제20권12호
• /
• pp.3970-3979
• /
• 1996

A fluid flow inside a circular cylinder subject to horizontal, circular oscillation is analyzed numerically and experimentally. The steady streaming velocities at the edges of the boundary layers on the bottom and side surfaces of the cylinder obtained in the previous paper are used as the boundary conditions in the governing equations for the steady flow motion in the interior region. The Stokes' drift velocity obtained in the previous paper also constitutes the Lagrangian velocity which is used in the momentum equations. It turns out that the interior steady flow is composed of one cell, ascending at the center and descending near the side surface, at the streaming Reynolds number 2500. However, at the streaming Reynolds number 25, the flow field is divided into two cells resulting in a descending flow at the center. The experimentally visualized flow patterns at the bottom surface agree well with the analytical solutions. The visualization experiment also confirms the flow direction as well as the center position of the cell obtained by the numerical solutions.

• 한국전기전자재료학회논문지
• /
• 제16권6호
• /
• pp.501-509
• /
• 2003

We have designed transflective liquid crystal display(LCD) associated with in-plane switching of a LC director driven by fringe-field, unlike other LCD mode. Reflective area consists of a λ/2 compensation film and a LC cell with retardation value(dΔn) of λ/4 with their optic axes making an angle of 15$^{\circ}$ and 75$^{\circ}$ against polarizer, respectively. In the transmissive area, top and bottom polarizers are parallel each other, an LC has a dΔn of λ/2, and another λ/2 compensation film is inserted between the LC cell and bottom polarizer. With the configuration, both devices show dark state initially. When an incident light is 550nm, the device shows wide-viewing-angle characteristics such that in the reflective area the contrast ratio target than 5 exists up to 55$^{\circ}$ of polar angle in all directions and in transmissive area it exists about 100$^{\circ}$ in vortical direction and 110$^{\circ}$ in horizontal direction.

• 한국환경복원기술학회지
• /
• 제9권5호
• /
• pp.1-9
• /
• 2006

The purpose of this study is to make a design guideline in designing constructed wetland which can treat water quality both of point and nonpoint source water pollution. It focuses on structural aspects of two case studies of constructed wetland applying SSB(Sustainable Structured wetland Biotope) system in Korea. The constructed wetland of Lake Ju-am which was constructed in 2002 by Environmental Management Corporation, was designed by applying SSB system. It shows higher removal efficiency than expected - 56% of BOD removal efficiency, 60% of T-N removal, and 76% of T-P removal efficiency. In two cases, total wetland areal extents were calculated referred to treatment efficiency. The system is consist of micro-cell structures : inflow channel, forebay, multiple wetland cells and micro-pool. When designing constructed wetland appropriate in local area, the total organic system of vertical and horizontal structure : geology, hydrology, land use, and ecological surroundings of the sites should be considered totally.

• 센서학회지
• /
• 제13권3호
• /
• pp.188-194
• /
• 2004

With a remarkable advance in CMOS (complimentary metal-oxide-semiconductor) process technology, a variety of vision sensors with signal processing circuits for complicated functions are actively being developed. Especially, as the principles of signal processing in human retina have been revealed, a series of vision chips imitating human retina have been reported. Human retina is able to detect the edge and motion of an object effectively. The edge detection among the several functions of the retina is accomplished by the cells called photoreceptor, horizontal cell and bipolar cell. We designed a CMOS vision chip by modeling cells of the retina as hardwares involved in edge and motion detection. The designed vision chip was fabricated using $0.6{\mu}m$ CMOS process and the characteristics were measured. Having reliable output characteristics, this chip can be used at the input stage for many applications, like targe tracking system, fingerprint recognition system, human-friendly robot system and etc.

• 대한공간정보학회지
• /
• 제25권1호
• /
• pp.71-78
• /
• 2017

최근 널리 보급되고 있는 태양광 발전소의 유지관리를 위해 다양한 연구들이 시도되고 있다. 본 연구에서는 unmanned aerial vehicle(UAV)기반 열적외선 센서를 이용하여 태양광 셀의 발열을 분석하는 것으로서 주요 결론은 다음과 같다. 먼저 UAV 기반 RGB 센서를 이용하여 정사영상과 digital surface model(DSM) 자료를 구축하였으며, 이를 통해 태양광 셀의 발열 분석에 필요한 태양광 모듈 레이어를 생성하였다. 또한 태양광 모듈 레이어의 위치정확도를 평가하기 위해 virtual reference service(VRS) 측량을 이용하여 검정점에 대한 수평오차를 분석한 결과, 표준오차가 $dx={\pm}2.4cm$, $dy={\pm}3.2cm$로 높은 위치정확도를 확보할 수 있었다. 그리고 태양광 셀의 발열 실험을 위해 고무패치를 설치한 후 UAV 열적외선 센서를 이용하여 발열이 생기는 고무패치의 위치를 효과적으로 분석할 수 있었다. 또한 고무패치 셀 비율과 UAV 열적외선 센서에 의한 셀 비율의 표준오차는 ${\pm}3.5%$로 나타났으며, 따라서 UAV 기반 열적외선 센서를 이용하여 태양광 셀의 발열을 효과적으로 분석할 수 있었다. 아울러 발열이 생기는 셀이 위치하고 있는 태양광 모듈의 코드를 자동으로 추출함으로서 효과적인 태양광발전소 유지보수가 가능하게 되었다.

• 대한원격탐사학회지
• /
• 제29권4호
• /
• pp.423-441
• /
• 2013

이 연구에서는 MTSAT-2 적외 영상과 수증기 영상을 이용하여 2010년 9월 21일 추석 호우 사례에 대하여 대류운 생애주기의 각 단계에서 나타나는 특징을 조사하였다. 추석 호우와 관련된 최초의 구름은 20일 1630~1900 UTC에 서해 중부 지역에서 관측된 다중 세포의 하층운이다. 이 구름 가운데 일부가 1930 UTC에 산동반도 부근에서 휘도온도 $-45^{\circ}C$ 이하의 대류 세포로 발달한다. 이 때 이 지역은 수증기 영상에서 암역의 가장자리에 위치한다. 대류 세포는 동진하다가 한반도 중서부 해안 부근에서 21일 0030과 0430 UTC에 두 차례의 병합을 거쳐 급격히 발달한다. 이후 21일 0430에서 1000 UTC까지 약 6시간 동안 위성 영상에서 구름의 면적은 상대적으로 작고, 수평 이동속도는 느려졌다. 최저 휘도온도는 약 $-75{\sim}-65^{\circ}C$로 매우 낮게 유지되며, 잘 발달한 부세포가 반복적으로 형성되는 특징을 보인다. 레이더 자료에는 국지적으로 50 mm/hr 이상의 강우율을 보이는 좁은 띠 모양의 강우 밴드가 나타나고 이 밴드는 대류운의 남서쪽 가장자리에 위치한다. 그러나 수치 모델 자료의 종관 규모 역학적 강제항에는 뚜렷한 특징을 찾기 어렵다. 대류 세포의 구름 면적은 21일 1000 UTC 이후 짧은 시간에 급격한 증가를 보이고 뒤이어 소멸한다. 이러한 대류 세포의 발달과 관련된 위성 영상의 특징은 중규모 호우의 초단기 예보와 실시간 예보에 사용될 수 있을 것이다.

• Journal of Mechanical Science and Technology
• /
• 제16권8호
• /
• pp.1095-1101
• /
• 2002

The load characteristics of engine main bearing are very important in the design of crankshaft and engine block. The stiffness of crankshaft and block, or the optimal dimension of the bearing can be determined according to the load level. This paper presents the load characteristics of engine main bearing. Two components of the main bearing load are measured during engine firing and motoring. The vertical and horizontal load components are measured by using the dynamic load cell mounted in each main bearing cap bolt. The measured main bearing loads are compared with calculated results by using the statically determinate method. The theoretical results, provided in this study, agreed well with the experimental results. The presented results are very useful for achieving optimal design of engine.