• 대한조선학회지
• /
• 제22권1호
• /
• pp.1-8
• /
• 1985

The buckling characteristics of cylindrical shells with a circular hole, under axially compressed loads, have been analyzed and the results have been compared with existed experimental results. Deflection function with decay factor is assumed, and stress distribution around a circular hole in tensioned infinite plate is used for formulating buckling energy function. Applying Rayleigh Ritz procedure to this energy function, characteristic equation of eigenvalue problem is determined. Buckling load is defined by the minimum value of eigenvalues calculated according to several decay factors, and as the radius ratios of a circular hole (a/R) and shell thickness ratios (R/t) are varied, the reducing characteristics of buckling load are studied. As a result, buckling loads are reduced by about 50% according to some radius ratios ($a/R{\geq}0.15$) of circular hole and are not nearly affected by shell thickness ratio(R/t).

• Structural Engineering and Mechanics
• /
• 제36권6호
• /
• pp.669-678
• /
• 2010

In general means, the stress concentration problem of elastic plate with a rectangular hole can be investigated by numerical methods, and only approximative results are derived. This paper deduces an analytical study of the stress concentration due to a rectangular hole in an elastic plate under bending loads. Base on classical elasticity theory and FEM applying the U-transformation technique, the uncoupled governing equations with 3-DOF are established, and the analytical displacement solutions of the finite element equations are derived in series form or double integral form. Therefore, the stress concentration factor can then be discussed easily and conveniently. For the plate subjected to unidirectional bending loads, the non-conforming plate bending element with four nodes and 12-DOF is taken as examples to demonstrate the application of the proposed method. The inner force distribution is obtained. The solutions are adequate for the condition when the hole is far away from the edges and the thin plate subjected to any transverse loadings.

• 한국소음진동공학회논문집
• /
• 제19권2호
• /
• pp.192-199
• /
• 2009

This paper presents the free vibration analysis of a circular plate with a concentric square hole. The boundary condition is the edge of the square hole is free and the outer circular plate is simply supported. Due to the geometric abnormality, this analysis does not permit an exact solution. The present problem deals with the numerical calculation of the natural frequencies and mode shapes of vibration of the structure by independent coordinate coupling method(ICCM). The numerical results show the efficacy of the ICCM and changes in natural frequencies and modes due to the square hole size.

• KSII Transactions on Internet and Information Systems (TIIS)
• /
• 제11권11호
• /
• pp.5574-5591
• /
• 2017

Inspired by the idea of Artificial Immune System, many researches of wireless sensor network (WSN) intrusion detection is based on the artificial intelligent system (AIS). However, a large number of generated detectors, black hole, overlap problem of NSA have impeded further used in WSN. In order to improve the anomaly detection performance for WSN, detector generation mechanism need to be improved. Therefore, in this paper, a Differential Evolution Constraint Multi-objective Optimization Problem based Negative Selection Algorithm (DE-CMOP based NSA) is proposed to optimize the distribution and effectiveness of the detector. By combining the constraint handling and multi-objective optimization technique, the algorithm is able to generate the detector set with maximized coverage of non-self space and minimized overlap among detectors. By employing differential evolution, the algorithm can reduce the black hole effectively. The experiment results show that our proposed scheme provides improved NSA algorithm in-terms, the detectors generated by the DE-CMOP based NSA more uniform with less overlap and minimum black hole, thus effectively improves the intrusion detection performance. At the same time, the new algorithm reduces the number of detectors which reduces the complexity of detection phase. Thus, this makes it suitable for intrusion detection in WSN.

• 대한수학회지
• /
• 제42권6호
• /
• pp.1251-1264
• /
• 2005

Let D be an acyclic digraph. The competition graph of D has the same set of vertices as D and an edge between vertices u and v if and only if there is a vertex x in D such that (u, x) and (v, x) are arcs of D. The competition number of a graph G, denoted by k(G), is the smallest number k such that G together with k isolated vertices is the competition graph of an acyclic digraph. It is known to be difficult to compute the competition number of a graph in general. Even characterizing the graphs with competition number one looks hard. In this paper, we continue the work done by Cho and Kim[3] to characterize the graphs with one hole and competition number one. We give a sufficient condition for a graph with one hole to have competition number one. This generates a huge class of graphs with one hole and competition number one. Then we completely characterize the graphs with one hole and competition number one that do not have a vertex adjacent to all the vertices of the hole. Also we show that deleting pendant vertices from a connected graph does not change the competition number of the original graph as long as the resulting graph is not trivial, and this allows us to construct infinitely many graph having the same competition number. Finally we pose an interesting open problem.

• 한국연소학회:학술대회논문집
• /
• 한국연소학회 2004년도 제28회 KOSCO SYMPOSIUM 논문집
• /
• pp.102-111
• /
• 2004

Partial quenching structure of turbulent diffusion flames in a turbulent mixing layer is investigated by the method of flame hole dynamics to develope a prediction model for the turbulent lift off. The present study is specifically aimed to remedy the problem of the stiff transition of the conditioned partial burning probability across the crossover condition by adopting level-set method which describes propagating or retreating flame front with specified propagation speed. In light of the level-set simulations with two model problems for the propagation speed, the stabilizing conditions for a turbulent lifted flame are suggested. The flame hole dynamics combined with level-set method yields a temporally evolving turbulent extinction process and its partial quenching characteristics is compared with the results of the previous model employing the flame-hole random walk mapping. The probability to encounter reacting' state, conditioned with scalar dissipation rate, demonstrated that the conditional probability has a rather gradual transition across the crossover scalar dissipation rate in contrast to the stiff transition of resulted from the flame-hole random walk mapping and could be attributed to the finite response of the flame edge propagation.

• 대한기계학회논문집A
• /
• 제24권9호
• /
• pp.2167-2173
• /
• 2000

The HANARO (High-flux Advanced Neutron Application Reactor) has operated since 1995. The Cold Neutron(CN) hole was implanted in the reflector tank from the design stage. Before a vacuum chamber and a moderator cell for the cold neutron source are installed into the CN hole, it is necessary to measure the exact size of the inside diameter and thickness of the CN hole to prevent the interference problem. Due to inaccessibility and high radiation field in the CN hole, a mechanical measurement method is not permitted. The immersion ultrasonic technique is considered as the best method to measure the thickness and the diameter. The 4 axis manipulator of the 2 channel of a sensor module was fabricated. The transducer of 10 MHz results in 0.03 nun of resolution. The inside diameter and thickness for 550 points of the CN hole were measured using 2 channel ultrasonic sensors. The results showed that the thickness is in the range of 13-6.7 mm and inside diameter is in the range of o 156-165. These data will be a good reference in the design of a cold neutron source facility.

• 지능정보연구
• /
• 제20권4호
• /
• pp.107-120
• /
• 2014

본 연구에서는 사회연결망분석기법 중 하나인 구조적 공백 분석 결과를 이용하여 추천과정에 사용자의 정성적이고 감성적인 정보를 반영할 수 있는 협업필터링 기반의 추천시스템을 제안한다. 협업필터링은 추천기술 중 가장 많이 활용되고 있지만 전통적으로 확장성과 희박성 등의 문제점뿐 만 아니라 사용자-상품 매트릭스의 선호도만을 이용하여 추천을 함으로써 사용자의 정성적이고 감성적인 정보를 추천과정에 반영하지 못한다는 한계점이 있다. 본 연구에서 제안하는 추천시스템은 사회연결망분석에서 중심성 분석과 함께 연결망 내의 주요개체를 탐지할 수 있는 구조적 공백 분석을 이용하여 연결망 내의 대표 사용자들을 추출한 후 이들을 중심으로 군집을 형성한 후 각 군집색인 협업필터링을 수행하는 과정을 통해 전통적인 협업필터링에서 반영하지 못했던 정성적, 감성적 정보를 반영한다. 한편, 군집색인 협업필터링을 수행함으로써 추천의 효율성을 높일 수 있는 장점도 있다. 본 연구에서는 실제 사용자들의 상품에 대한 선호도 평가점수와 사용자들의 사회연결망 정보를 수집하여 실험을 수행하고 전통적인 협업필터링과 다양한 형태의 협업필터링과의 추천성과 비교를 통하여 제안하는 시스템의 유용성을 확인한다. 비교모형으로는 전통적인 협업필터링, 임의 군집색인 기반 협업필터링, k평균 군집색인 기반 협업필터링을 이용한 추천시스템이며, 실험 결과, 제안한 모형이 다른 비교모형에 비해 추천성과의 정확도가 가장 우수하였다. 추천성과의 차이에 대한 통계적 유의성 검정 결과, 제안 모형은 전통적인 협업필터링 기반의 추천시스템과는 통계적으로 유의한 성과 차이가 없었으나, 다른 두 모형에 대해서는 통계적으로 유의한 성과의 차이가 있는 것으로 나타났다.

• 대한기계학회논문집A
• /
• 제21권3호
• /
• pp.430-438
• /
• 1997

Deburring and edge finishing technology as the final process of machining operation is required for manufacturing of advanced precise conponents. But, deburring is considered as a difficult problem on going to the high efficient production and automation in the FMS. Removal of burr couldn't have a standard of its definition because of its various shapes, dimensions and properties and mostly depends on manual treatment. Especially, deburring for cross hole inside is very difficult owing to its shape passing through out perpendicular to a main hole. The electrochemical method is suggested as its solution in practical aspect. Therefore, electrochemical deburring technology needs to be developed for the high efficiency and automation of internal deburring in the cross hole. In this study, the new process in the eliminating burr inside cross hole, electrochemical deburring by the wheel electroplated with Cubic-Boron-Nitrade abrasives, is suggested. Its deburring mechanism is described and machining performances is investigated. Also, CBN electroplated wheel is designed and manufactured and then characteristics of electrochemical deburring are investigated through experiments. Overall electrochemical deburring performance against burr inside cross hole is examined in the various power sources such as peak current and direct current.

• 한국정밀공학회:학술대회논문집
• /
• 한국정밀공학회 1996년도 춘계학술대회 논문집
• /
• pp.19-23
• /
• 1996

Deburring and edge finishing technology as the last process of machining operation is required for manufacturing of advanced procesion components, duburring has treated as a difficult problem on going tothe highefficency, automation in the FMS. Removal of butt with various shapes, dimensions and properties coultn't has a standard and has depended on manual treatment. Especially, deburring for cross hole inside owing to passing through out perpendicular to a main hole is more difficult, the electrolytic method is proper as its solution at practical aspects. Therefore, for the high effciency and automation of intermal deburring in the cross hole, development of electrolytic debutting technology is needed. So, the new process in the burr treatment is supposed. In this study, in the eliminating burr inside cross hole, the principle and machining performances of electrochemical deburring by Cubic-Boron-Nitrade abrasive electroplate wheel are investigated, Design and manufacture of CBN electroplated wheel and analysis of characteristics with electrolytic debutting are achieved. Also deburring efficiency and electrolytic performance for cross hole were examined according to electrolytic current and electrolytic deburring condition corresponding to acquired edge quality was found out.