• The Transactions of the Korean Institute of Power Electronics
• /
• v.3 no.4
• /
• pp.399-406
• /
• 1998

This paper proposes an instantaneous torque control method for the high performance SRM drive. In first, we e establish SRM model with the characte1istics of the torque. phase current and rotor position which were measured in t the experimental SRM. Based on this model. the reference torque waveform to minimize torque ripple is obtained by t the control of resultant torque considering phase torque overlap according to the variation of load and speed. And the r reference current waveform for the tracking of reference torque are decided. The control method for tracking the r reference current is used the delta modulation technique. The proposed method is validated by the comparing with S simulation and experimental results.

• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.36 no.2C
• /
• pp.78-85
• /
• 2011

In this paper we proposed an intelligent PTZ camera system which detects, classifies and tracks moving objects. If a moving object is detected, features are extracted for classification and then realtime tracking follows. We used GMM for detection followed by shadow removal. Legendre moment is used for classification. Without auto focusing, we can control the PTZ camera movement by using center points of the image and object's direction, distance and velocity. To implement the realtime system, we used TI DM6446 Davinci processor. Throughout the experiment, we obtained system's high performance in classification and tracking both at vehicle's normal and high speed motion.

• The Journal of the Korea institute of electronic communication sciences
• /
• v.6 no.6
• /
• pp.855-864
• /
• 2011

In this paper, a nonlinear controller based on adaptive back-stepping method is proposed for high performance operation of IPMSM(Interior Permanent Magnet Synchronous Motor). First, in order to improve the performance of speed tracking a nonlinear back-stepping controller is designed. Since it is difficult to control the high performance driving without considering parameter variation, a parameter estimator is included to adapt to the variation of load torque in real time. In addition, for the efficiency of power consumption of the motor, controller is designed to operate motor with minimum current for maximum torque. The proposed controller is applied through simulation to the a 2-hp IPMSM for the angular velocity reference tracking performance and load torque volatility estimation, and to test the MTPA(Maximum Torque per Ampere) operation in constant torque operation region. The result verifies the efficacy of the proposed controller.

• Journal of the Korean Society for Precision Engineering
• /
• v.15 no.8
• /
• pp.17-25
• /
• 1998

Aluminum alloys have low density, relatively high strength and yield strength, good plasticity, good machinability, and high corrosion and acid resistance. Therefore, they are suitable for large containers for the food, chemical and other industries. Large containers are often bodies of revolution consisting of shell courses, stiffening rings, heads and other elements joined by annular welds. Larger containers have longer welds and require greater leak-tightness and higher weld mechanical properties. The LNG tank consists of aluminum plates with various sizes, so its construction should by divided by several sections. Moreover, each section has its own sub-section consisted of several aluminum plates. To guarantee the quality of huge LNG tank, therefore, the precise control of plate dimension should by urgently needed in conjunction with the appropriate selection of process parameters such as cutting speed, depth of cut, rotational speed and so on. In this paper, a manufacturing system was developed to implement automatic circular tracking in height direction and automatic circular interpolation in depth of cut direction. Also, the neural network based on the backpropagation algorithm was used to predict the cutting quality and motor load related with the life time of the developed system. It was revealed that the manufacturing system and the neural network could be effectively applied to the bevelling process and to predict the quality of machined area and the motor load.

• Journal of Institute of Control, Robotics and Systems
• /
• v.6 no.10
• /
• pp.871-880
• /
• 2000

A twin-servo mechanism is used to increase the payload capacity and assembling speed of high precision motion control systems such as semiconductor chip mounters. In this paper, we focus on the modeling of the twin-servo system and propose its network representation. And also, we propose a robust synchronizing motion control algorithm to cancel out the skew motion of the twin-servo system caused by different dynamic characteristics of two driving systems and the vibration generated by high accelerating and decelerating motions. The proposed control algorithm consists of separate feedback motion control algorithms for each driving system and a skew motion compensation algorithm. A robust tracking controller based on internal-loop compensation is proposed as a separate motion controller and its disturbance attenuation property is shown. The skew motion compensation algorithm is also designed to maintain the synchronizing motion during high speed operation, and the stability of the whole closed loop system is proved based on passivity theory. Finally, experimental results are shown to illustrate control performance.

• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 2000.11a
• /
• pp.754-758
• /
• 2000

In recent years, the LDM(Linear DC Motor) is widely used, because it has more merits than other rotary motors. First, if system requires linear motion, LDM realizes direct linear motion as rotary motor does not. Second, system is simple and easy to control, and so on. In optical disc drive, a tracking system consists of two parts. One is fine actuating and the other is coarse actuating. For coarse actuating VCM(Voice Coil Motor) actuator is used as a basic drive mechanism. In this paper, MC(Moving Coil) type LDM is designed, manufactured and controlled. System is composed of mechanical-electromagnetic component, therefore mechanical loss and electromagnetic loss exist. The dominent mechanical loss is friction which results from sliding between guide shaft and hole. Therefore, this paper shows the friction compensation control. High speed and accurate position is not gained only PID control, therefore other control method is applied to the system.

• Proceedings of the KSME Conference
• /
• 2008.11a
• /
• pp.984-989
• /
• 2008

An estimation of high-order damping in flexible multibody dynamic simulation is introduced in this paper. The suggested damping model based on the experimental modal analysis leads to more accurate correlation results comparing to the traditional linear damping model because it directly uses the modal parameters of each mode achieved from experiment even high frequency modes. The modal parameters until the 5th mode are extracted from the experimental modal testing of the flexible beam using a high speed camera. And using the measured damping ratio and natural frequency until the 5th mode, the generic damping model is constructed. Then, the ANCF (absolute Nodal Coordinate Formulation) simulation results are compared to experimental results until the 5th mode.

• Ocean and Polar Research
• /
• v.29 no.4
• /
• pp.311-316
• /
• 2007

Ocean noise may be used for monitoring wind speed and rainfall rate on the sea surface, as well as for tracking whales' migration routes. In particular, low-frequency ocean noise has recently been of concern with relation to the behavior of marine mammals. Low-frequency ocean noise has been increasing over the past few decades due to increase of ship traffic and offshore oil industry activities. Mechanical noise such as flow noise and cable strumming noise may be induced if low-frequency ocean noise is measured by cabled traditional hydrophone in high current areas. To successfully measure low-frequency ocean noise in a shallow water environment with strong current, we developed a self-recording hydrophone. This paper describes the main configurations of the self-recording hydrophone and presents some results on measured data.

• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 2003.05a
• /
• pp.1170-1175
• /
• 2003

Recently, the disturbance caused by an optical disk vibration and the external vibration/shock are more serious problem in an optical disk drives (ODD) as an ODD become small size and rotation speed increases. The conventional controller cannot cope with the mentioned problems properly when the disturbance and vibration are larger than some range. Therefore, we propose a new control scheme using a disturbance observer (DOB) and it can control the aforementioned problems. The designed the controller is applied to a commercial ODD in focusing direction, then its validity is proved by experimental method. By rising the disturbance observer theory, the focusing performance is conspicuously improved in the presence of sinusoidal vibrations or a shock disturbance. This algorithm also applies to a tracking structure also, because focusing structure is very similar to it.

• Proceedings of the KSR Conference
• /
• 2005.11a
• /
• pp.275-281
• /
• 2005

In this paper, a new algorithm is proposed for high speed roaming in an Intelligent Train Control System(ITCS) and study on optimized positioning of radio communication equipment. A DCS(Data Communication System) which is a main part of CBTC(Communication Based Train Control) system, is consisted of radio based wireless communication system and wired optical system. In the radio based wireless communication, the position of AP enclosures and antennas shall be optimized for the guaranteed communication channel between wayside and trains both in open aired and tunnelled area. Also a communication channel established between wayside and train shall be maintained while train moves at its maximum speed. This study shows the way of determining the optimal position for the railway side communication equipment in Bundang Line and how to achieve continuous communicating channel for tracking and controlling train.