• 한국산학기술학회논문지
• /
• 제18권2호
• /
• pp.737-742
• /
• 2017

본 최근 기존의 모습과는 다른 고층건물의 형태가 대도시에서 랜드마크로서 주목을 끌고 있으며 혁신적인 건물형태에 대한 탐색은 건축분야에서 지속적으로 이루어질 것이다. 본 연구에서는 소규모의 구조체에 활용되고 있는 $Isotruss^{(R)}$ 그리드를 건물의 외주골조에 적용하여 구조적 성능을 검토하였다. 구조적 거동을 비교하기 위해 다이아그리드 구조시스템을 준거로 하였다. 동일한 규모의 16층, 32층, 48층 건물을 두가지의 구조시스템으로 설계하였다. 아이소트러스 그리드 구조 부재의 선정은 예비적 설계단계로 생각하여 다이아그리드의 강성에 기준한 설계방법을 이용하였다. 경사기둥의 각도로 아이소트러스 구조는 $59^{\circ}$, 다이아그리드 구조는 $68.2^{\circ}$로 하였다. 횡강성, 철골량, 외부골조의 횡력 부담비율, 기둥의 축력 강도비, 고유 진동수를 비교하였다. 6개의 건물 모델을 해석한 결과 두 구조시스템의 구조적 성능은 유사하나 외주골조의 횡하중 분담율이 아이소트러스 그리드 구조가 93.3%로 다이아그리드 구조의 88.7% 보다 약간 커서 코어 기둥의 배치에 있어 유리하다고 볼 수 있다. 따라서 본 연구에서 제안하는 아이소트러스 그리드 시스템은 입면형태가 독특할 뿐만 아니라 기존의 구조시스템과 동등한 구조적 성능을 보유한 것으로 보인다.

• Earthquakes and Structures
• /
• 제14권4호
• /
• pp.349-360
• /
• 2018

Reinforced concrete (RC) moment frames supported on two ground levels have been widely constructed in mountainous areas with medium to high seismicity in China. In order to investigate the seismic collapse behavior and risk, a scaled frame model was tested under constant axial load and reversed cyclic lateral load. Test results show that the failure can be induced by the development of story yielding at the first story above the upper ground. The strong column and weak beam mechanism can be well realized at stories below the upper ground. Numerical analysis model was developed and calibrated with the test results. Three pairs of six case study buildings considering various structural configurations were designed and analyzed, showing similar dynamic characteristics between frames on two ground levels and flat ground of each pair. Incremental dynamic analyses (IDA) were then conducted to obtain the seismic collapse fragility curves and collapse margin ratios of nine analysis cases designated based on the case study buildings, considering amplification of earthquake effect and strengthening measures. Analysis results indicate that the seismic collapse safety is mainly determined by the stories above the upper ground. The most probable collapse mechanism may be induced by the story yielding of the bottom story on the upper ground level. The use of tie beam and column strengthening can effectively enhance the seismic collapse safety of frames on two ground levels.

• 비파괴검사학회지
• /
• 제27권1호
• /
• pp.48-57
• /
• 2007

사용 중인 항공기 구조를 모사하여 리벳구멍 주위에 피로균열이 존재하는 AA2024-T3 박판을 CFRP 복합재 패치로 접합하여 보수한 후 피로균열 성장거동을 음향방출(AE)을 측정하면서 관찰하였다. 패칭의 효과로 균열성장속도의 뚜렷한 감소와 균열이 인접한 리벳 구멍으로 전파되는 시간을 지연시키는 효과가 있음을 확인하였다. 그리고 패칭 후 균열성장에 의해 탐지된 신호와 패치와 알루미늄 사이의 접합계면 분리에 의한 신호의 구별 가능성을 다변량 자료분석 기법인 주성분분석을 통해 알아보았다. 그 결과 균열성장에 따른 AE신호는 계면분리에 따른 AE신호에 비해 중심주파수가 높고 작은 에너지를 가지는 반면, 계면분리 신호는 균열성장 신호에 비해 상승시간이 길고 중심주파수가 상대적으로 낮으며 비교적 큰 에너지를 가진 것으로 나타났다. 따라서 AE신호의 유형인식 방법은 AE 발생원의 위치표정 결과와 결합할 경우 패치 접합으로 보수된 구조에서의 피로균열 성장거동을 예측하는 방법으로 충분히 활용될 수 있다.

• 한국강구조학회 논문집
• /
• 제28권1호
• /
• pp.53-64
• /
• 2016

상 하부 스플릿 티 접합부는 보-기둥 모멘트 접합부의 한 형태로 T-stub 플랜지의 두께, 고장력볼트의 게이지 거리, 고장력볼트의 개수, 고장력볼트의 직경 등의 변화에 따라서 상이한 거동특성을 나타낸다. 상 하부 스플릿 티 접합부는 일반적으로 상 하부에 체결된 T-stub이 휨모멘트를 지지하고 전단탭이 전단력을 지지하는 것으로 이상화하여 설계되고 있다. 그러나 중 저층 강구조물에 상 하부 스플릿 티 접합부가 적용되면 보 부재의 규격이 작아지므로 보 웨브에 전단탭을 설치할 수 없는 경우가 발생할 수 있다. 이 연구는 이와 같이 보 웨브에 전단탭 설치가 어려운 기하학적 형상을 갖는 상 하부 스플릿 티 접합부가 충분한 전단력 지지능력을 발현하도록 하는 접합부상세를 제안하기 위하여 진행하였다. 이를 위하여 상 하부 스플릿 티 접합부에 대한 실험체를 제작하여 실물대 실험을 수행하였다.

• Wind and Structures
• /
• 제31권3호
• /
• pp.241-253
• /
• 2020

The inerter-based vibration absorber (IVA) is an enhanced variation of Tuned Mass Damper (TMD). The parametric optimization of absorbers in the previous research mainly considered only two decision variables, namely frequency ratio and damping ratio, and aimed to minimize peak displacement and acceleration individually under the excitation of the across-wind load. This paper extends these efforts by minimizing two conflicting objectives simultaneously, i.e., the extreme displacement and acceleration at the top floor, under the constraint of the physical mass. Six decision variables are optimized by adopting a constrained multi-objective evolutionary algorithm (CMOEA), i.e., NSGA-II, under fluctuating across- and along-wind loads, respectively. After obtaining a set of optimal individuals, a decision-making approach is employed to select one solution which corresponds to a Tuned Mass Damper Inerter/Tuned Inerter Damper (TMDI/TID). The optimization procedure is applied to parametric optimization of TMDI/TID installed in a 340-meter-high building under wind loads. The case study indicates that the optimally-designed TID outperforms TMDI and TMD in terms of wind-induced vibration mitigation under different wind directions, and the better results are obtained by the CMOEA than those optimized by other formulae. The optimal TID is proven to be robust against variations in the mass and damping of the host structure, and mitigation effects on acceleration responses are observed to be better than displacement control under different wind directions.

• 한국화재소방학회논문지
• /
• 제24권2호
• /
• pp.162-171
• /
• 2010

산업의 발전에 따라 사회양상도 복잡 다양하게 변화하여 오고 생활의 편리함도 늘어났지만, 그에 따른 화재위험요인도 함께 증가하고 있다. 최근 국내 건축물 환경도 초고층화 인텔리전트(Intelligent)화 되어가면서 화재로 인한 인적 물적 손실은 계속적으로 증가하고 있어 과거보다 화재발생을 줄일 수 있는 제도적 장치를 보완하여야 한다. 본 연구의 목적은 특정소방대상물 관리제도에 대한 전반적인 운영 실태와 문제점을 도출하여 특정소방대상물의 방화관리 등급체계 개선방안을 제시하는데 있다. 개선방안으로는 화재 위험성 평가제도 도입, 가칭 "소방안전공사"의 신설, 특정소방대상물 방화관리등급 재분류, 초고층 및 지하심층 건축물에 방화관리자 신설 등이다.

• 한국환경복원기술학회지
• /
• 제24권2호
• /
• pp.1-17
• /
• 2021

As population concentration, high-rise, and high-density progresses amid rapid industrialization and urbanization in Korea, green areas in the city have decreased significantly and the natural environment has deteriorated day by day due to various development projects. In order to cope with these social changes, many studies related to park and green areas have been conducted, but in the case of Gwangju-si, only studies on green areas such as vegetation structures, street facilities, and recreation forests have been conducted on park green areas. The situation is not losing. Therefore, in this study, a survey was conducted on Gwangju citizens to understand the usage behavior and satisfaction of park green areas, and to provide basic data for future park development and reorganization. As a result, first, to induce a variety of static and dynamic activities in order to increase the park satisfaction of Gwangju citizens, it is possible to create a park that has not been formed as soon as possible, and by planning programs with various themes. Second, it is necessary to expand green space services in marginalized areas by creating water streams, flower pots, and rooftop greening around the lives of Gwangju citizens, and create park green spaces with themes using cultural and historical resources for each administrative district. Third, in order to solve the dry landscape in some urban areas, it is necessary to establish a three-dimensional landscape plan by creating a variety of green areas such as potted plants, green areas, and street trees, and by giving functions of park green areas such as expanding leisure and convenience facilities.

• Advances in Computational Design
• /
• 제4권1호
• /
• pp.53-72
• /
• 2019

Safety measures for tower cranes are extremely important among the seismic countermeasures at high-rise building construction sites. In particular, the collapse of a tower crane from a high position is a very serious catastrophe. An example of such an accident due to an earthquake is the case of the Taipei 101 Building (the author was the project director), which occurred on March 31, 2002. Failure of the bolted joints of the tower-crane mast was the direct cause of the collapse. Therefore, it is necessary to design for this eventuality and to take the necessary measures on construction sites. This can only be done by understanding the precise dynamic behavior of mast joints during an earthquake. Consequently, we created a new hybrid-element model (using beam, shell, and solid elements) that not only expressed the detailed behavior of the site joints of a tower-crane mast during an earthquake but also suppressed any increase in the total calculation time and revealed its behavior through computer simulations. Using the proposed structural model and simulation method, effective information for designing safe joints during earthquakes can be provided by considering workability (control of the bolt pretension axial force and other factors) and less construction cost. Notably, this analysis showed that the joint behavior of the initial pretension axial force of a bolt is considerably reduced after the axial force of the bolt exceeds the yield strength. A maximum decrease of 50% in the initial pretension axial force under the El Centro N-S Wave ($v_{max}=100cm/s$) was observed. Furthermore, this method can be applied to analyze the seismic responses of general temporary structures in construction sites.

• Wind and Structures
• /
• 제36권6호
• /
• pp.405-421
• /
• 2023

Strong wind is the main factors of wind-damage of high-rise buildings, which often creates largely economical losses and casualties. Wind pressure plays a critical role in wind effects on buildings. To obtain the high-resolution wind pressure field, it often requires massive pressure taps. In this study, two traditional methods, including bilinear and bicubic interpolation, and two deep learning techniques including Residual Networks (ResNet) and Generative Adversarial Networks (GANs), are employed to reconstruct wind pressure filed from limited pressure taps on the surface of an ideal building from TPU database. It was found that the GANs model exhibits the best performance in reconstructing the wind pressure field. Meanwhile, it was confirmed that k-means clustering based retained pressure taps as model input can significantly improve the reconstruction ability of GANs model. Finally, the generalization ability of k-means clustering based GANs model in reconstructing wind pressure field is verified by an actual engineering structure. Importantly, the k-means clustering based GANs model can achieve satisfactory reconstruction in wind pressure field under the inputs processing by k-means clustering, even the 20% of pressure taps. Therefore, it is expected to save a huge number of pressure taps under the field reconstruction and achieve timely and accurately reconstruction of wind pressure field under k-means clustering based GANs model.

• 한국농공학회지
• /
• 제26권1호
• /
• pp.52-72
• /
• 1984

This study was performed to obtain the basic data which can be applied to the use of epoxy resin mortars. The data was based on the properties of epoxy resin mortars depending upon various mixing ratios to compare those of cement mortar. The resin which was used at this experiment was Epi-Bis type epoxy resin which is extensively being used as concrete structures. In the case of epoxy resin mortar, mixing ratios of resin to fine aggregate were 1: 2, 1: 4, 1: 6, 1: 8, 1:10, 1 :12 and 1:14, but the ratio of cement to fine aggregate in cement mortar was 1 : 2.5. The results obtained are summarized as follows; 1.When the mixing ratio was 1: 6, the highest density was 2.01 g/cm$^3$, being lower than 2.13 g/cm$^3$ of that of cement mortar. 2.According to the water absorption and water permeability test, the watertightness was shown very high at the mixing ratios of 1: 2, 1: 4 and 1: 6. But then the mixing ratio was less than 1 : 6, the watertightness considerably decreased. By this result, it was regarded that optimum mixing ratio of epoxy resin mortar for watertight structures should be richer mixing ratio than 1: 6. 3.The hardening shrinkage was large as the mixing ratio became leaner, but the values were remarkably small as compared with cement mortar. And the influence of dryness and moisture was exerted little at richer mixing ratio than 1: 6, but its effect was obvious at the lean mixing ratio, 1: 8, 1:10,1:12 and 1:14. It was confirmed that the optimum mixing ratio for concrete structures which would be influenced by the repeated dryness and moisture should be rich mixing ratio higher than 1: 6. 4.The compressive, bending and splitting tensile strenghs were observed very high, even the value at the mixing ratio of 1:14 was higher than that of cement mortar. It showed that epoxy resin mortar especially was to have high strength in bending and splitting tensile strength. Also, the initial strength within 24 hours gave rise to high value. Thus it was clear that epoxy resin was rapid hardening material. The multiple regression equations of strength were computed depending on a function of mixing ratios and curing times. 5.The elastic moduli derived from the compressive stress-strain curve were slightly smaller than the value of cement mortar, and the toughness of epoxy resin mortar was larger than that of cement mortar. 6.The impact resistance was strong compared with cement mortar at all mixing ratios. Especially, bending impact strength by the square pillar specimens was higher than the impact resistance of flat specimens or cylinderic specimens. 7.The Brinell hardness was relatively larger than that of cement mortar, but it gradually decreased with the decline of mixing ratio, and Brinell hardness at mixing ratio of 1 :14 was much the same as cement mortar. 8.The abrasion rate of epoxy resin mortar at all mixing ratio, when Losangeles abation testing machine revolved 500 times, was very low. Even mixing ratio of 1 :14 was no more than 31.41%, which was less than critical abrasion rate 40% of coarse aggregate for cement concrete. Consequently, the abrasion rate of epoxy resin mortar was superior to cement mortar, and the relation between abrasion rate and Brinell hardness was highly significant as exponential curve. 9.The highest bond strength of epoxy resin mortar was 12.9 kg/cm$^2$ at the mixing ratio of 1:2. The failure of bonded flat steel specimens occurred on the part of epoxy resin mortar at the mixing ratio of 1: 2 and 1: 4, and that of bonded cement concrete specimens was fond on the part of combained concrete at the mixing ratio of 1 : 2 ,1: 4 and 1: 6. It was confirmed that the optimum mixing ratio for bonding of steel plate, and of cement concrete should be rich mixing ratio above 1 : 4 and 1 : 6 respectively. 10.The variations of color tone by heating began to take place at about 60˚C, and the ultimate change occurred at 120˚C. The compressive, bending and splitting tensile strengths increased with rising temperature up to 80˚ C, but these rapidly decreased when temperature was above 800 C. Accordingly, it was evident that the resistance temperature of epoxy resin mortar was about 80˚C which was generally considered lower than that of the other concrete materials. But it is likely that there is no problem in epoxy resin mortar when used for unnecessary materials of high temperature resistance. The multiple regression equations of strength were computed depending on a function of mixing ratios and heating temperatures. 11.The susceptibility to chemical attack of cement mortar was easily affected by inorganic and organic acid. and that of epoxy resin mortar with mixing ratio of 1: 4 was of great resistance. On the other hand, when mixing ratio was lower than 1 : 8 epoxy resin mortar had very poor resistance, especially being poor resistant to organicacid. Therefore, for the structures requiring chemical resistance optimum mixing of epoxy resin mortar should be rich mixing ratio higher than 1: 4.