• 동력기계공학회지
• /
• 제4권3호
• /
• pp.34-39
• /
• 2000

Performance data in the literature on air lift pumps have been based primarily on pumps of long length and large diameter (high lift pumps). Since mariculture operations involve pumps of relatively short length and small diameter, performance data are required for efficient operation. To provide such data, an experimental apparatus was designed and fabricated to test all lift pumps from 2.1 to 3.4 cm inside diameter and from 40 to 300 cm in length. Instrumentation was provided to measure water flow rate and air flow rate as well as water temperature, air temperature, and pressure throughout the system. Results from this study correlate well with high lift pump data in that, for a given pump geometry, maximum water flow occurs for a specific air flow rate. Driving the pump with air flows larger or smaller than this optimum flow rate will decrease the pumping rate. The optimum flows are significantly different for low lift pumps compared to high lift pumps. However, the pumping rate for low lift pumps approaches that for high lift pumps with increasing length.

• 항공우주시스템공학회지
• /
• 제7권3호
• /
• pp.1-6
• /
• 2013

Numerical optimization of two dimensional high lift configuration was performed with flow solver and optimization method based on RSM(Response Surface Model). Navier-Stokes solver with Spalart-Allmaras turbulence model was selected for the simulation of highly complex and separated flows on the flap. For the simultaneous optimization of both flap shape and setting (gap/overlap), 10 design variables (eight variables for flap shape variation and two variables for flap setting) were chosen. In order to generate the response surface model, 128 experimental points were selected for 10 design variables. The objective function considering maximum lift coefficient, lift to drag ratio and lift coefficient at specific angle of attack was selected to reduce flow separation on the flap surface. The present method was applied to two dimensional fowler flap in landing configuration. After applying the present method, it was shown that the optimized high lift configuration had less flow separation on the flap surface and lift to drag ratio was suppressed over entire angle of attack range.

• 한국건축시공학회:학술대회논문집
• /
• 한국건축시공학회 2018년도 춘계 학술논문 발표대회
• /
• pp.6-7
• /
• 2018

Although the importance of the construction lift is increasing, no improvements are being made to its operating system. This study proposed an optimal call-response algorithm of the construction lift for high-rise building construction by using image sensing technology, height measuring sensor, and load cell. This algorithm makes turn-around decision of the construction lift by considering the information and the number of user. It occurs when the call comes from a floor where the construction lift already have passed. The purpose of this study is to reduce the total latency of the construction lift user. Furthermore, it is possible to prevent delay in construction duration by carrying out a priority operation of the construction lift for the critical workforce.

• 산업경영시스템학회지
• /
• 제32권1호
• /
• pp.34-43
• /
• 2009

In this thesis, we explain developing processes of the power transmission system for lift truck. Conventional power transmission system had some problems such as spatial constraints or low speed and high torque problem. Because conventional power transmission system was mainly designed for high speed vehicles. In this paper we developed power shift drive axle specialized for $2.0{\sim}3.5$ ton lift truck. Innovative structure of transmission which is built in inside axle, enables to reduce system weight and size by 40% compared to the conventional power transmission system. Also, it is possible to do additional functions such as auto parking system and anti-roll back system.

• Journal of Power Electronics
• /
• 제9권6호
• /
• pp.854-865
• /
• 2009

Super-lift dc-dc converters are a series of advanced step-up dc-dc topologies that provide high voltage transfer gains by super-lift techniques. This paper presents a developed graphical modelling method for super-lift converters and gives a thorough analysis with a consideration of the effects caused by parasitic parameters and diodes' forward voltage drop. The general guidelines for constructing and deriving graphical models are provided for system analysis. By applying it to examples, the proposed method shows the advantages of high convenience and feasibility. Both the circuit simulation and experimental results are given to support the theoretical analysis.

• 한국자동차공학회논문집
• /
• 제23권5호
• /
• pp.502-507
• /
• 2015

In this paper, we built a three-dimensional model by applying reverse engineering techniques on targeting the intake port of 2900cc class diesel engine before that three-dimensional design technique is applied. The performance of the intake port is predicted and analysed using the computational flow analysis. Flow Coefficient and Swirl Ratio have been analyzed for two intake port models. One is the intake port for the diesel engine with plunger-type fuel system, and the other is for the diesel engine with CRDI fuel system. Computational result shows that the Flow Coefficient of the intake port with CRDI fuel system is increased upto 10 percentage compared with that with plunger-type. Also, the intake port with plunger-type has high Swirl Ratio at high valve lift, and the intake port with CRDI fuel system has high Swirl Ratio at relatively low valve lift. It is believed that because of high performance of the fuel injector, the intake port with CRDI fuel system is designed for more air amount and not much swirl flow at high valve lift. However, high swirl flow is required at low valve lift for initial fuel and air mixing. The result of this study may be useful for the re-manufacturing industry of automotive parts.

• 한국전산유체공학회:학술대회논문집
• /
• 한국전산유체공학회 2011년 춘계학술대회논문집
• /
• pp.362-367
• /
• 2011

The aerodynamic performance of the pantograph of the next generation high sped train is analyzed. The calculation of the flow around pantograph is carried cut by FLUENT; by the steady state flow calculation with ${\kappa}-{\omega}$ SST turbulence model, the lift force of the pantograph is computed. For the verification of the numerical schemes am grid systems, flow calculations are performed with the pantograph shape which was used at the experiments performed at Railway Technical Research Institute (RTRI) in Japan. Then, the difference of lift force between numerical am experimental results is about 10%. Therefore, selected numerical schemes and the current grid system is adequate for the analysis am prediction of the aerodynamic performance of panthograph system. Based on these numerical schemes am grid system, the flow around pantograph of the next generation high sped train is calculated and the lift force of the pantograph is predicted; the lift force of the pantograph is about 146N.

• 한국전산유체공학회:학술대회논문집
• /
• 한국전산유체공학회 2011년 춘계학술대회논문집
• /
• pp.441-446
• /
• 2011

To investigate aerodynamic performance of high-lift devices, 2D design is the base of the success of high-lift system design for transport aircraft, which can shorten the periods of three-dimensional design and analysis. For the simulation coupled viscous and inviscous euler method (MSES) is used. In this parametric study, Gap and Overlap which can define position of flap is used as design variables and we investigale relation between angle of attack and flap position for lift enhancement.

• 한국건설관리학회논문집
• /
• 제14권5호
• /
• pp.153-163
• /
• 2013

건축물이 고층화, 대형화 될수록 수직 양중 계획 및 운영에 관한 중요성이 부각되고 있다. 이에 프로젝트 초기 단계에 실제 모델과 유사한 건설용 리프트 양중계획을 수립하려는 노력이 계속되고 있지만 프로젝트 착수 후 리프트 운행을 컨트롤 할 수 있는 시스템은 부재한 실정이다. 따라서 본 논문에서는 건설용 리프트 운영 효율증대를 위하여 센서를 사용한 리프트 운행 정보를 수집하고 실시간 분석이 가능한 건설용 리프트 최적화 운행 시스템 개발을 실시 및 검증 단계를 수행하여, 양중 효율의 지표가 되는 사용자 대기 시간의 단축을 도모하고 향후 무인 스마트 리프트의 초석이 되는 시스템을 제시하고자 한다.

• 항공우주시스템공학회지
• /
• 제16권2호
• /
• pp.49-62
• /
• 2022

본 논문에서는 항공기 고양력 제어시스템의 모델해석 기반 설계과정 및 검증결과를 제시한다. 이를 위하여 가장 많이 사용되는 상용 물리모델 툴 중 하나인 Matlab/Simulink를 활용하였다. 고양력 제어시스템은 기능 및 주요 에너지 흐름에 따라 전자제어, 유압구동, 그리고 기계동력전달 도메인의 3가지 도메인으로 나눌 수 있다. 우리는 이에 근거하여 주요 도메인 및 하위 부품 각각을 모델링 한 후 그것을 통합하여 전체 시스템 모델을 완성하였다. 모델링 과정에서 각각의 모델 블록은 자체 사전시험 및 부품의 수락시험 결과를 참고하여 튜닝하였으며, 결과적으로 전체 성능모델과 개발이 끝난 단위 제품 및 전체 시스템은 각각의 제품단위 시험 및 시스템 통합 성능시험을 통해 완전히 검증되었다. 마지막으로 고양력 제어시스템의 개발과정 및 결과를 요약하고 추후 과제를 제시할 것이다.