• 대한금속재료학회지
• /
• 제49권8호
• /
• pp.635-641
• /
• 2011

The effect of high shear speed on shear force, shear energy and fracture surface was investigated for the solder joint of a $Sn-_{3.0}Ag-_{0.5}Cu$ ball. For both ENIG and OSP pads, the shear force increased with an increase in shearing speed to 0.3 m/s. However, for an ENEPIG pad, the shear force increased with an increase in shear speed to 0.6 m/s and kept almost constant afterward. The shear energy decreased with an increase in shearing speed for ENIG and OSP pads. For the ENEPIG pad, however, the shear energy almost remained constant in a shearing speed range 0.3-3.0 m/s. The fracture mode analysis revealed that the amount of brittle fracture for the ENIG and the OSP pads increased with shearing speed, and a complete brittle fracture appeared at 1.0 m/s for ENIG and 2.0 m/s for OSP. However, the ENEPIG pad showed only a ductile fracture until 0.25 m/s, and a full brittle fracture didn't occur up to 3.0 m/s. The fracture mode matched well with the shear energy. The results from the high speed shear test of SAC305 were similar to those of SAC105.

• 대한금속재료학회지
• /
• 제47권9호
• /
• pp.580-585
• /
• 2009

The effects of shear speed and tip height on the high speed shear test of Sn-3.0wt.%Ag-0.5wt.%Cu ball joints were investigated. Solder balls of $450{\mu}m$ in diameter were reflowed at $245^{\circ}C$ on a FR4 PCB (Printed Circuit Board) in order to obtain a sample for the high-speed shear test. The UBM was comprised of Cu/Ni/Au, and the shear speed and tip height varied from 0.5 to 3.0 m/s, and from 10 to $135{\mu}m$, respectively. According to the experimental results, faster shear speed enhanced the shear strength of the solder joints, regardless of the tip height. The fraction of ductile (solder) fracture decreased when the shearing speed was raised from 0.5 to 3.0 m/s. With an increasing tip height from 10 to 50 and $135{\mu}m$, the fracture mode changed from pad lift to mixed (ductile and brittle) and ductile fracture, respectively, while the shearing energy also increased in the same order. The shear energy had a proportional relationship with the fraction of the solder fracture.

• 한국공작기계학회:학술대회논문집
• /
• 한국공작기계학회 2003년도 춘계학술대회 논문집
• /
• pp.454-459
• /
• 2003

The paper will present chip formation mechanism and surface integrity generation mechanism based on the systematical experimental tests. Some basic factors such as the end milling cutter tooth number, cutting forces, cutting temperature, cutting vibration, the chip status, the surface roughness, the hardness distribution and the metallographic texture of the machined surface layer are involved. the chip formation mechanism is typical thermal plastic shear localization at high cutting speed with less number og shear ribbons and bigger shear angle than at low speed, which means lack of chip deformation. The high cutting speed with much more cutting teeth will be beneficial to the reduction of cutting forces, enlarge machining stability region, depression of temperature increment, auti-fatigability as well as surface roughness. The burrs always exists both at low cutting speed and at high cutting speed. So the deburr process should be arranged for milling titanium alloy in any case.

• Structural Engineering and Mechanics
• /
• 제78권4호
• /
• pp.413-423
• /
• 2021

Piers are the main lateral force-resisting members of high-speed railway (HSR) bridges used in China and are characterized by low axial load ratios, low longitudinal reinforcement ratios, low stirrup ratios, and high shear span ratios. It is well known that flexural, flexural-shear, and shear failures of piers may occur during an earthquake. In this study, a new shear strength model was developed to simulate the seismic failure of HSR solid piers accurately. First, low cyclic-loading test data of solid piers obtained in recent years were collected to set up a database for model verification. Second, based on the test database, the applicability of existing shear strength models was evaluated. Finally, a new shear strength model for HSR solid piers with round-ended cross-sections was derived based on the truss model and ultimate equilibrium theory. In comparison with existing models, it was demonstrated that the proposed model could be used to predict the shear strength of HSR piers more accurately.

• 대한금속재료학회지
• /
• 제49권3호
• /
• pp.237-242
• /
• 2011

The effect of shearing speed on the shear force and energy of Sn-0Ag-0.5Cu solder ball was investigated. Various UBM (under bump metallurgy)'s on Cu pads were used such as ENEPIG (Electroless Nickel, Electroless Palladium, Immersion Gold; Ni/Pd/Au), ENIG (Electroless Nickel, Immersion Gold; Ni/Au), OSP (Organic Solderability Preservative). To fabricate a shear test specimen, a solder ball, $300{\mu}m$ in diameter, was soldered on a pad of FR4 PCB (printed circuit board) by a reflow soldering machine at $245^{\circ}C$. The solder bump on the PCB was shear tested by changing the shearing speed from 0.01 m/s to 3.0 m/s. As experimental results, the shear force increased with a shearing speed of up to 0.6 m/s for the ENIG and the OSP pads, and up to 0 m/s for the ENEPIG pad. The shear energy increased with a shearing speed up to 0.3 m/s for the ENIG and the OSP pads, and up to 0.6 m/s for the ENEPIG pad. With a high shear speed of over 0 m/s, the ENEPIG showed a higher shear force and energy than those of the ENIG and OSP. The fracture surfaces of the shear tested specimens were analyzed, and the fracture modes were found to have closer relationship with the shear energy than the shear force.

• International Journal of Korean Welding Society
• /
• 제5권1호
• /
• pp.15-28
• /
• 2005

The ball shear test was investigated in terms of the effects of test parameters, i.e., shear height and shear speed, with an experimental and non-linear finite element analysis for evaluating the solder joint integrity of area array packages. Two representative Pb-free solder compositions were examined in this work: Sn-3.5Ag-0.75Cu and In-48Sn. The substrate was a common SMD type with solder bond pad openings of 460 $\mu$m in diameter. The microstructural investigations were carried out using SEM, and the IMCs were identified with EDS. Shear tests were conducted with the two varying test parameters. It could be observed that increasing shear height, at fixed shear speed, has the effect of decreasing shear force for both Sn-3.5Ag-0.75Cu and In-48Sn solder joints, while the shear force increased with increasing shear speed at fixed shear height. Too high shear height could cause some undesirable effects on the test results such as unexpected high standard deviation values or shear tip sliding from the solder ball. The low shear height conditions were favorable for screening the type of brittle interfacial fractures or the degraded layers in the interfaces. The shear speed conditions were discussed with the stress analyses of the solder ball, and we cannot find any conspicuous finding which is related to optimum shear speed from the stress analyses.

• 마이크로전자및패키징학회지
• /
• 제15권4호
• /
• pp.65-70
• /
• 2008

본 연구에서는 BGA(Ball Grid Array) 솔더 접합부에 high impact가 가해졌을 경우 접합부의 기계적 특성에 대해서 연구하였다. 시편은 ENIG(Electroless Nickel Immersion Gold) 표면 처리된 FR-4 기판 위에 직경이 500 ${\mu}m$인 Sn-37Pb 솔더볼을 BGA 방식으로 배열하고 리플로우(Reflow)를 통하여 제작하였다. HTS(High Temperature Storage) 테스트를 위해, 시편을 일정한 온도의 $120^{\circ}C$에서 250시간 동안 시효처리(Aging)를 실시하였다. 시효처리 후, 각각의 시편은 고속 전단 시험기(Dage-4000HS)를 이용하여 속도 변수는 0.01, 0.1, 1, 3 m/s로 설정하여 고속전단 시험을 실시하였다. 전단시험 후, 솔더 접합 계면과 파면을 주사전자현미경(Scanning Electron Microscope, SEM)을 통하여 관찰하였다. 솔더 접합 계면에는 $Ni_3Sn_4$의 금속간 화합물이 성장하였으며, 시효처리 후, 솔더 접합 계면에 생성된 금속간 화합물의 두께가 증가하는 것을 관찰 할 수 있었다. 전단 시험 결과, 전단 속도가 빨라짐에 따라 전단 강도값은 증가하는 경향을 나타내었다. 솔더 접합부의 파단은 전단 속도와 시효처리 시간에 따라 다양한 파괴 모드로 진행됨을 알 수 있었다. 또한, 파괴 모드는 연성파괴 형상을 보이다가 전단속도가 증가함에 따라 취성 파괴 형상으로 변하는 것을 알 수 있었다.

• 마이크로전자및패키징학회지
• /
• 제21권3호
• /
• pp.43-50
• /
• 2014

전자 제품의 경박 단소화 및 고집적화가 이루어 지면서 실리콘 집과 인쇄회로기판의 인터커넥션의 고신뢰도가 요구되고 있다. 본 연구는 Sn-4.0wt%Ag-0.5wt%Cu (SAC405) 솔더와 다양한 무전해 Ni-P 도금 두께에서의 high speed shear 에너지 및 파괴 모드를 연구하였다. 파괴 모드 분석을 위하여 집속이온빔(FIB) 분석이 이용되었다. 질산 기상 처리하지 않은 $1{\mu}m$ Ni-P 시편에서 낮은 shear 에너지가 나왔으며, 이는 솔더레지스트 선단에서 파단의 원인을 제공하는 것이 확인되었다. 질산 기상 처리한 시편에서 무전해 Ni-P 도금 두께가 커질수록 취성 파괴 모드는 감소한다. 또 Ni-P 도금 두께와 표면 거칠기(Ra)는 반비례 관계를 가진다. 이는 Ni-P 도금의 표면 거칠기를 낮추면 SAC405 솔더 조인트의 신뢰도를 향상시킨다는 사실을 나타낸다.

• 대한기계학회:학술대회논문집
• /
• 대한기계학회 2008년도 추계학술대회A
• /
• pp.250-255
• /
• 2008

This study utilized a high speed lap-shear test to evaluate the mechanical behavior of Sn-37Pb/Cu and Sn-37Pb/Electroless Nickel immersion Gold under bump metallization solder joints under high speed loading and hence the drop reliability. The samples were aged for 120 h at different temperatures ($120^{\circ}C,\;150^{\circ}C,\;170^{\circ}C$) and afterward tested at different displacement rates (0.01 mm/s to 500 mm/s) to examine the effects of aging on the drop life reliability. The combination of the stress-strain graphs captured from the shear tests and identifying a fracture mode dominant in the samples for different strain rates leads us to conclude that the drop reliability of solder joints degrades as the aging temperature increases, possibly due to the role of the IMC layer. This study successfully demonstrates that the analysis based on a high speed lap-shear test could be critically used to evaluate the drop reliability of solder joints.

• 한국공작기계학회논문집
• /
• 제12권5호
• /
• pp.34-39
• /
• 2003

The paper will present chip formation mechanism and surface integrity generation mechanism based on the systematical experimental tests. Some basic factors such as the end milling cutter tooth number, cutting forces, cutting temperature, cutting vibration the chip status, the surface roughness, the hardness distribution and the metallographic texture of the machined surface layer are involved. The chip formation mechanism is typical thermal plastic shear localization at high cutting speed with less number of shear ribbons and bigger shear angle than that at low speed, which means lack of chip deformation. The high cutting speed with much more cutting teeth will be beneficial to the reduction of cutting forces, enlarge machining stability mot depression of temperature increment anti-fatigability as well as surface roughness. The burrs always exist both at low cutting speed and at high cutting speed. So the deburring process should be arranged for milling titanium alloy in my case.