• Journal of the Optical Society of Korea
• /
• v.12 no.1
• /
• pp.42-48
• /
• 2008

The relative intensity noise (RIN) characteristics in 405 nm blue laser diodes grown on wurtzite AlGaInN multiple quantum well structures were investigated using the rate equations with the quantum Langevin noise model. The device parameters were extracted from the optical gain properties of the MQW active region using the self-consistent numerical method developed for calculating the multiband Hamiltonian in the strained wurtzite crystal. These methods have been applied to laser diodes for various conditions including the external feedback and the high frequency current injection.

• Proceedings of the KIPE Conference
• /
• 2003.11a
• /
• pp.119-122
• /
• 2003

This paper describes the sensorless technique for the surface-mounted permanent-magent synchronous motor(SPMSM or PMSM) drive based on magnetic saliency. The control technique is a sensorless control algorithm that injects the high frequency voltage to the stator terminal in order to estimate the rotor position and speed. The rotor position and speed for sensorless vector control is achieved by appropriate signal processing to extract the position information from the stator current in the low speed range including zero speed. Proposed sensorless algorithm using the double-band hysteresis controller and initial rotor position detection exhibits excellent reference tracking and increased robustness. Experimental results are presented to verify the feasibility of the proposed control schemes.

• Journal of Power Electronics
• /
• v.19 no.4
• /
• pp.956-967
• /
• 2019

This paper introduces a virtual signal injected maximum torque per ampere (MTPA) control strategy for direct-torque-controlled five-phase interior permanent magnet synchronous motor (IPMSM) drives. The key of the proposed method is that a high frequency signal is injected virtually into the stator flux linkage. Then the responding stator current is calculated and regulated to compensate the amplitude of the flux linkage. This is done according to the relationship between the stator current and the stator flux linkage. Since the proposed method does not inject any real signals into the motor, it does not cause any of the problems associated with high-frequency signals, such as additional copper loss and extra torque ripple. Simulation and experimental results are offered to verify the effectiveness of the proposed method.

• The Transactions of the Korean Institute of Power Electronics
• /
• v.27 no.1
• /
• pp.80-83
• /
• 2022

This paper proposes an initial rotor polarity detection algorithm of a single-phase permanent magnet synchronous motor (SP-PMSM) related to stable open-loop starting for sensorless operation. Generally, the SP-PMSM needs an asymmetric air-gap structure to can avoid the initial starting failure at zero torque point. Therefore, the rotor polarity information can be obtained by using the DC offset current direction of a stator current through a high frequency voltage injection into an SP-PMSM with an asymmetric air gap. In this paper, the proposed rotor initial polarity detection algorithm is verified through several experimental results.

• Journal of the Korean Society of Combustion
• /
• v.3 no.1
• /
• pp.59-69
• /
• 1998

The results of study on the active control of naturally occurring combustion oscillations with a single dominant frequency in an atmospheric dump combustor are presented. Control was achieved by an oscillatory infection of secondary fuel at the dump plane. A high speed solenoid valve with a maximum frequency of 250Hz was used as the actuator and a sound level meter, located at the combustor exit, measured the pressure fluctuations which served as the feedback signal for the control loop. Instability characteristics were mapped over a range of mean mixing section velocities from 6.7 m/s-9.3 m/s and with three mixing conditions. Different fuel/air mixing conditions were investigated by introducing varying percentages of primary fuel at two locations, one at the entrance to the mixing section and one 6 mixing tube diameters upstream of the dump plane. Control studies were conducted at a mean velocity of 9.3 m/s, with an air temperature of $415^{\circ}C$, and from flame blowout to the stoichiometric condition.

• Proceedings of the KIEE Conference
• /
• 2005.11a
• /
• pp.217-219
• /
• 2005

To detect partial discharge of 154kV joint box, we have made experiment by using the HFCT sensor. Generally the signals which are detected in partial discharge test of underground power transmission cable are accompanied with both noises of high voltage and noises of surrounding power cable. The most noise in near to end part of joint box is corona, beside other noises flowed from surrounding area. Partial discharge test is difficulty due to these noises. First, we test reliability on both injection of calibration signal in NJB and removal of low frequency. After that, we had analyzed frequencies by measuring signals in IJB with 300[m] distance from NJB. Also we had measured S/N ratio by using the indirected injection method of calibration signal in IJB. In this experiment, two measurement methods were difference of detection acquisition, but these had the equal frequency properties.

• Proceedings of the KIEE Conference
• /
• 2007.04b
• /
• pp.75-78
• /
• 2007

To detect partial discharge of 154kV joint box, we have made experiment by using the HFCT sensor. Generally the signals which are detected in partial discharge test of underground power transmission cable are accompanied with both noises of high voltage and noises of surrounding power cable. The most noise in near to end part of joint box is corona, beside other noises flowed from surrounding area. Partial discharge test is difficulty due to these noises. First, we test reliability on both injection of calibration signal in NJB and removal of low frequency. After that, we had analyzed frequencies by measuring signals in IJB with 300[m] distance from NJB. Also we had measured S/N ratio by using the indirected injection method of calibration signal in IJB. In this experiment, two measurement methods were difference of detection acquisition, but these had the equal frequency properties.

• Journal of Forest and Environmental Science
• /
• v.34 no.5
• /
• pp.376-381
• /
• 2018

For the control of oak wilt caused by Raffaelea quercus-mongolicae, an antifungal microorganism, Streptomyces blastmyceticus, was used as a potential agent. Culture suspension of S. blastmyceticus was injected into Quercus mongolicae in the research forest of Kangwon National University by $ChemJet^{(R)}$ trunk injection and Macro-infusion at root flare injection. $Alamo^{(R)}$ (a.i., propiconazole 14.5%), a fungicide currently used for the control of oak wilt in USA, was also treated by both methods to compare the efficacy. For preventive efficacy, culture suspension of the pathogen was inoculated at 1 month after injection of either agent. Tested trees were cut at 3 months after treatment, stained with 1% Fuchsin acid, and then non-conductive area (NCA) and re-isolation frequency (RIF) of oak wilt fungus were compared among treatments. While NCA was the highest as 47.3% in pathogen only treatment, it was the lowest as 16.0% in sterilized water treatment by Macro-infusion. NCAs of Alamo treatment by Macro-infusion and ChemJet injection were 25.3% and 32.1%, respectively. NCA of S.blastmyceticus treatment by ChemJet injection was 32.3%, similar with Alamo treatment's by ChemJet injection. All treatments by either injection method showed significantly lower NCA compared to the pathogen only treatment. These results indicate that S. blastmyceticus injection shows the preventive efficacy against oak wilt disease by suppressing the growth of pathogen injected. NCA of Macro-infusion injection of sterilized water was lower as 16.0%, compared to 21.3% of ChemJet injection. It means that Macro-infusion is more effective in translocation of sterilized water than ChemJet injection by even distribution. RIF from wood discs of treated trees showed high in pathogen only treatment, but relatively low in S. blastmyceticus treatment. RIF results were correlated with NCA results. From the above results, it was confirmed that S. blastmyceticus showed preventive efficacy against oak wilt disease by ChemJet trunk or Macro-infusion at root flare injection.

• Journal of dental hygiene science
• /
• v.5 no.2
• /
• pp.51-56
• /
• 2005

This study investigated the medicines prescribed in dental services in order to provide information and materials on dental clinics and hospitals, for the intention of leading the dental circle to make efforts for voluntary improvement, do adequate prescription, and attempt for bench marking through this unfolding of their tendency in continuous prescription behaviors, and leading the people to have a right recognition on adequate medicine use through this information on their medicine-taking behaviors including antibiotics and injections. From the records of outpatient prescriptions of medicines under health insurance over the period of June 1st to September 31th in 2003 in the 34,226 recuperation institutions, antibiotics and injections were analyzed into administration days, prescription frequency, medicine cost per administration day, the number of medicines per prescription, and the number weight of high priced medicines. The findings were as below: 1. Adminstration days of antibiotics was 90.11% in the dental clinics, which was a decrease than the same quarter and the previous quarter of the previous year. While the prescription frequency of antibiotics was 15.5%, higher than the same quarter and the previous quarter of the previous year. In dental hospitals, administration days and prescription frequency of antibiotics were 71.57% and 21.05%, respectively, a little higher than the previous quarter. Compared to other kind of recuperation institutions, dental clinics and hospitals had higher administration days and lower prescription frequency. 2. For injections, adminstration days and prescription frequency in dental clinics were 0.13% and 0.05%, respectively, which were decreases than the same quarter of the previous year. In dental hospitals, adminstration days and prescription frequency were 1.03% and 0.88%, respectively, a little lower than those of the previous quarter. Compared to other kind of recuperation institutions, dental clinics and hospitals were very lower in injection administration days and injection prescription frequency. 3. The number of prescribed medicines was 2.79 in the dental clinics, which was lower than the same quarter of the previous year but higher than the previous quarter. Dental hospitals put 2.67 numbers of medicines per prescription, an increase than the same quarter of the previous year and the previous quarter. Compared to other kind of recuperation institutions, dental clinics and hospitals put smaller number of medicines per prescription. 4. Medicine cost per administration day was 863 won in the dental clinics, which was an increase than the same quarter of the previous year and in the previous quarter. Compared to other kind of recuperation institutions, dental clinics and hospitals had lower medicine cost per administration day. 5. The number weight of high priced medicines was 46.43% in dental clinics, which was an increase than the previous quarter. In dental hospitals, it was 54.05%, so remarkable an increase than the previous quarter. Compared to other kind of hospitals and clinics, dental clinics and hospitals prescribed larger number of high priced medicines. 6. By districts, the frequency of antibiotics prescriptions was the highest in Kwanju and the lowest in Daejeon. The frequency of injection prescriptions was high in all Youngnam districts as was in the second quarter, while low in all the Metropolitan districts. There was a large variation in the prescription frequency to the districts, as the district of the highest prescription frequency had more than 2 times larger frequency than the district of the lowest frequency. Medicine cost per administration day was the highest in Ulsan but the lowest in the north part of Cholla province. The number of medicines per prescription was the largest in Kyonggi province while the smallest in Cheju-do.

• Journal of the Korea Institute of Information Security & Cryptology
• /
• v.24 no.3
• /
• pp.453-460
• /
• 2014

Fault injection attack is the process of attempting to acquire the information on-chip through inject artificially generated error code into the cryptographic algorithms operation (or perform) which is implemented in hardware or software. From the details above, the laser-assisted failure injection attacks have been proven particularly successful. In this paper, we propose an improved laser probing system for fault injection attack which is called the Dual-Laser FA tool set, a hybrid approach of the Flash-pumping laser and fiber laser. The main concept of the idea is to improve the laser probe through utilizing existing equipment. The proposed laser probe can be divided into two parts, which are Laser-I for laser cutting, and Laser-II for fault injection. We study the advantages of existing equipment, and consider the significant parameters such as energy, repetition rate, wavelength, etc. In this approach, it solves the high energy problem caused by flash-pumping laser in higher repetition frequency from the fiber laser.