• 한국분말재료학회지
• /
• 제27권1호
• /
• pp.1-7
• /
• 2020

In this research, a new medium-entropy alloy with an equiatomic composition of FeCuNi was designed using a phase diagram (CALPHAD) technique. The FeCuNi MEA was produced from pure iron, copper, and nickel powders through mechanical alloying. The alloy powders were consolidated via a high-pressure torsion process to obtain a rigid bulk specimen. Subsequently, annealing treatment at different conditions was conducted on the four turn HPT-processed specimen. The microstructural analysis indicates that an ultrafine-grained microstructure is achieved after post-HPT annealing, and microstructural evolutions at various stages of processing were consistent with the thermodynamic calculations. The results indicate that the post-HPT-annealed microstructure consists of a dual-phase structure with two FCC phases: one rich in Cu and the other rich in Fe and Ni. The kernel average misorientation value decreases with the increase in the annealing time and temperature, indicating the recovery of HPT-induced dislocations.

• Applied Microscopy
• /
• 제45권1호
• /
• pp.9-15
• /
• 2015

In the present study, microstructural evolution in CuCrFeNi, CuCrFeNiMn, and CuCrFeNiMnAl alloys has been investigated. The as-cast CuCrFeNi alloy consists of a single fcc phase with the lattice parameter of 0.358 nm, while the as-cast CuCrFeNiMn alloy consists of (bcc+fcc1+fcc2) phases with lattice parameters of 0.287 nm, 0.366 nm, and 0.361 nm. The heat treatment of the cast CuCrFeNiMn alloy results in the different type of microstructure depending on the heat treatment temperature. At $900^{\circ}C$ a new thermodynamically stable phase appears instead of the bcc solid solution phase, while at $1,000^{\circ}C$, the heat treated microstructure is almost same as that in the as-cast state. The addition of Al in CuCrFeNiMn alloy changes the constituent phases from (fcc1+fcc2+bcc) to (bcc1+bcc2).

• 한국분말재료학회지
• /
• 제29권2호
• /
• pp.132-151
• /
• 2022

The CoCrFeMnNi high-entropy alloy (HEA), which is the most widely known HEA with a single face-centered cubic structure, has attracted significant academic attention over the past decade owing to its outstanding multifunctional performance. Recent studies have suggested that CoCrFeMnNi-type HEAs exhibit excellent printability for selective laser melting (SLM) under a wide range of process conditions. Moreover, it has been suggested that SLM can not only provide great topological freedom of design but also exhibit excellent mechanical properties by overcoming the strength-ductility trade-off via producing a hierarchical heterogeneous microstructure. In this regard, the SLM-processed CoCrFeMnNi HEA has been extensively studied to comprehensively understand the mechanisms of microstructural evolution and resulting changes in mechanical properties. In this review, recent studies on CoCrFeMnNi-type HEAs produced using SLM are discussed with respect to process-induced microstructural evolution and the relationship between hierarchical heterogeneous microstructure and mechanical properties.

• 열처리공학회지
• /
• 제37권2호
• /
• pp.58-65
• /
• 2024

In the present study, the effect of annealing condition on the microstructures and mechanical properties of the cold-rolled CoCrFeMnNi high entropy alloys were studied. Annealing treatment was performed under six different temperatures. Microstructural analyses confirmed that annealing below 800℃ resulted in the formation of intermetallic sigma (σ) phase within face-centered cubic (FCC) matrix, and this σ phase has beneficial effects on the formation of fine-grained structures through retardation of grain growth and recrystallization due to Zener pinning effect. This led to the enhanced yield strength and tensile strength of ~646 and ~855 MPa, respectively. The microstructures annealed above 800℃ demonstrated single FCC phase, and fully-recrystallized single FCC microstructure resulted in a slight increase in ductility with a considerable decrease in strength. The evolution of mechanical properties, such as strength, ductility, and strain hardening exponent, will be discussed.

• 소성∙가공
• /
• 제29권3호
• /
• pp.163-171
• /
• 2020

We present a multi-step cold drawing for a non-equiatomic Co₁₀Cr₁₅Fe₂₅Mn₁₀Ni₃₀V₁₀ high entropy alloy (HEA) with a simple face-centered cubic (FCC) crystal structure. The distribution of strain in the cold-drawn Co₁₀Cr₁₅Fe₂₅Mn₁₀Ni₃₀V₁₀ HEA wires was analyzed by the finite element method (FEM). The effective strain was expected to be higher as it was closer to the surface of the wire. However, the reverse shear strain acted to cause a transition in the shear strain behavior. The critical effective strain at which the shear strain transition behavior is completely shifted was predicted to be 4.75. Severely cold-drawn Co₁₀Cr₁₅Fe₂₅Mn₁₀Ni₃₀V₁₀ HEA wires up to 96% of the maximum cross-sectional reduction ratio were successfully manufactured without breakage. With the assistance of electron back-scattering diffraction and transmission electron microscope analyses, the abundant deformation twins were found in the region of high effective strain, which is a major strengthening mechanism for the cold-drawn Co₁₀Cr₁₅Fe₂₅Mn₁₀Ni₃₀V₁₀ HEA wire.

• Journal of Magnetics
• /
• 제12권4호
• /
• pp.133-136
• /
• 2007

We have carried out the study of magnetocaloric effect for as-quenched and annealed $Fe_{91-x}Y_xZr_9$ alloys. Samples were prepared by arc melting the high-purity elemental constituents under argon gas atmosphere and by single roller melt spinning. These alloys were annealed one hour at 773 K in vacuum chamber. The magnetization behaviours of the samples were measured by vibrating sample magnetometer. The Curie temperature increases with increasing Y concentration (x=0 to 8). Temperature dependence of the entropy variation ${\Delta}S_M$ was found to appear in the vicinity of the Curie temperature. The results show that annealed $Fe_{86}Y_5Zr_9$ and $Fe_{83}Y_8Zr_9$ alloys a bigger magnetocaloric effect than that those in as-quenched alloys. The value is 1.23 J/kg K for annealed $Fe_{86}Y_5Zr_9$ alloy and 0.89 J/kg K for as-quenched alloy, respectively. In addition, the values of ${\Delta}S_M$ for $Fe_{83}Y_8Zr_9$ alloy is 0.72 J/Kg K for as-quenched and 1.09 J/Kg K for annealed alloy, respectively.

• Tribology and Lubricants
• /
• 제39권1호
• /
• pp.13-20
• /
• 2023

Large drill bits may face high hardness ore and high working pressure when working. To optimize the use effect of large drill bits and prolong the use time, it is necessary to add a layer of pressure-resistant, wear-resistant, and low-friction coating on the surface of the drill bit. In this study, CoCrNiAlTi high-entropy alloy coatings and CoCrNiAlTi (70 wt%)-TiC (30 wt%) composite coatings are successfully prepared on Q235 steel by plasma spraying. The CoCrNiAlTi (70 wt%)-TiC (30 wt%) coating consists of FCC solid solution and a small amount of TiC phase. The effect of TiC on the composition phase, microhardness, and elastic modulus of HEA coating is studied by X-ray diffractometer (XRD) and microhardness tester. The effect of TiC on the friction and wear properties of HEA coatings is investigated using a wear tester. By improving the process parameters, the metallurgical bonding between the coating and the substrate is well combined, and a coating without pores and cracks is obtained. The experimental results confirm that the microhardness, elastic modulus, and wear resistance of CoCrNiAlTi-TiC composite coating are better, and the friction coefficient is lower.

• 한국분말재료학회지
• /
• 제31권1호
• /
• pp.8-15
• /
• 2024

The emergence of ferrous-medium entropy alloys (FeMEAs) with excellent tensile properties represents a potential direction for designing alloys based on metastable engineering. In this study, an FeMEA is successfully fabricated using laser powder bed fusion (LPBF), a metal additive manufacturing technology. Tensile tests are conducted on the LPBF-processed FeMEA at room temperature and cryogenic temperatures (77 K). At 77 K, the LPBF-processed FeMEA exhibits high yield strength and excellent ultimate tensile strength through active deformation-induced martensitic transformation. Furthermore, due to the low stability of the face-centered cubic (FCC) phase of the LPBF-processed FeMEA based on nano-scale solute heterogeneity, stress-induced martensitic transformation occurs, accompanied by the appearance of a yield point phenomenon during cryogenic tensile deformation. This study elucidates the origin of the yield point phenomenon and deformation behavior of the FeMEA at 77 K.

• 한국분말재료학회지
• /
• 제28권3호
• /
• pp.221-226
• /
• 2021

We fabricate the non-equiatomic high-entropy alloy (NE-HEA) Fe_49.5Mn₃₀Co₁₀Cr₁₀C_0.5 (at.%) using spark plasma sintering under various sintering conditions. Each elemental pure powder is milled by high-energy ball milling to prepare NE-HEA powder. The microstructure and mechanical properties of the sintered samples are investigated using various methods. We use the X-ray diffraction (XRD) method to investigate the microstructural characteristics. Quantitative phase analysis is performed by direct comparison of the XRD results. A tensile test is used to compare the mechanical properties of small samples. Next, electron backscatter diffraction analysis is performed to analyze the phase fraction, and the results are compared to those of XRD analysis. By combining different sintering durations and temperature conditions, we attempt to identify suitable spark plasma sintering conditions that yield mechanical properties comparable with previously reported values. The samples sintered at 900 and 1000℃ with no holding time have a tensile strength of over 1000 MPa.

• 한국분말재료학회지
• /
• 제26권6호
• /
• pp.515-527
• /
• 2019

High-entropy alloys (HEAs) are generally defined as solid solutions containing at least 5 constituent elements with concentrations between 5 and 35 atomic percent without the formation of intermetallic compounds. Currently, HEAs receive great attention as promising candidate materials for extreme environments due to their potentially desirable properties that result from their unique structural properties. In this review paper, we aim to introduce HEAs and explain their properties and related research by classifying them into three main categories, namely, mechanical properties, thermal properties, and electrochemical properties. Due to the high demand for structural materials in extreme environments, the mechanical properties of HEAs including strength, hardness, ductility, fatigue, and wear resistance are mainly described. Thermal and electrochemical properties, essential for the application of these alloys as structural materials, are also described.