• Culinary science and hospitality research
• /
• v.3
• /
• pp.165-179
• /
• 1997

Cost-volume-profit analysis shows the relationship between these factors. The figures expressed in a break-even chart can be used planning control and decision making. The relation ships can also be helpful in understanding how all costs must be covered in menu pricing. Involved in these relationship is the contribution to overhead and profit, or contribution ratio. This study used the food service operation of H hotel. Assumed the FC would be 10% of the High Volume, the VC would be 76% of the high volume. And in the CVP of individual meals, selected labor cost of the VC, assumed labor cost would be 35% of the volume.

• KIEE International Transaction on Electrical Machinery and Energy Conversion Systems
• /
• v.11B no.4
• /
• pp.180-184
• /
• 2001

The high operation frequency mainly reduces transformer volume in the power supply. A high frequency and high voltage pulse transformer is designed, fabricated, and tested. Switching frequency of the transformer is 100 kHz. Input and output voltages of the transformer are 250 V and 4 kV, respectively. Normal operation power of the transformer is 3 kW. Maximum volume of the transformer is 400 $cm^3$. The power density is thus 7.5 W/$cm^3$. The transformer will be installed in a metal box that has nominal operation temperature of 85 degree centigrade. The transformer and other high voltage components in the box will be molded with Silicon RTV(Room Temperature Vulcaniza) that has a very low thermal conductivity. Procedure of design and test results are discussed. Analytical as well as experimental results of varous paramters such as transformer loss, leakage inductance, distributed capacitance are also discussed. In addition, thermal analysis results from ANSYS code for three different operation conditions are discussed.

• Journal of the Korean Society for Aviation and Aeronautics
• /
• v.19 no.2
• /
• pp.37-44
• /
• 2011

This paper summarizes the HVO concept and procedures, presents a summary of the research and results, and outlines areas where future HVO is required. This concept enables people to get their destinations through shortest paths with advanced air traffic control system and equipments. The concept's key feature is that pilots maintain their own separation from other aircraft using air-to-air datalink and on-board software which are needed for supporting flight information present on the high Way in the sky display and airborne internet. By assigning Self-Controlled Area which assume pilot have separation responsibility, controllers evaluated SATS HVO concept as a successful method on the view of reduced workload and increased traffic level on high volume operation.

• International Journal of Automotive Technology
• /
• v.8 no.1
• /
• pp.19-25
• /
• 2007

This experimental study was carried out to obtain both low emissions and high thermal efficiency by rapid bulk combustion. Two kinds of experiments were conducted to obtain fundamental data on the operation of a RI engine by a radical ignition method. First, the basic experiments were conducted to confirm rapid bulk combustion by using a radical ignition method in a constant volume chamber (CVC). In this experiment, the combustion velocity was much higher than that of a conventional method. Next, to investigate the desirable condition of engine operation using radical ignition, an applied experiment was conducted in an actual engine based on the basic experiment results obtained from CVC condition. A sub-chamber-type diesel engine was reconstructed using a SPI type engine with controlled injection duration and spark timing, and finally, converted to a RI engine. In this study, the operation characteristics of the RI engine were examined according to the sub-chamber's specifications such as the sub-chamber volume and the diameter and number of passage holes. These experimental results showed that the RI engine operated successfully and was affected by the ratio of the passage hole area to the sub-chamber volume.

• Journal of the Ergonomics Society of Korea
• /
• v.23 no.2
• /
• pp.93-104
• /
• 2004

The research subjects of this study were 30 unmarried Korean women from 20 to 29 who had never had an operation on their breast. Measurement method using plaster breast mold was used for measuring their volume of breast. The correlation between their breast volume and the methods to set up brassiere cups with the existing method and with their circumference of breast was analyzed using KendalI's Coefficient. which was to figure out a method which had a bigger correlation with the volume of breast between the method to set up brassiere cups using the existing method and the method using the circumference of breast. The results analyzed showed that the coefficient of correlation between the existing method and the volume of breast was .12 and the significance level was .45. They didn't have any correlation. On the other hand. the coefficient of correlation between the circumference of breast and the volume of breast was .82. which was very high values and the significance level was very high .0001. Therefore. it turned out that it was difficult to set up brassiere cups by using the existing method and it was easier and more reliable to set up the cups by using the circumference of breast.

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.29 no.3 s.234
• /
• pp.418-424
• /
• 2005

We present the design, fabrication and experimental results of 4-bit digital microinjectors, whose ejected droplet volumes are adjusted by the digital operation of a 4-bit microheater array. We design the reference microinjectors as well as its comparative test structures. In the fabrication process, we use a five-mask micromachining process and the total chip size of the fabricated microinjector is $7,640{\mu}m{\times}5,260{\mu}m.$ We measure the ejected droplet volumes and velocities, which are adjusted from $12.1{\pm}1.0~55.6{\pm}14.7pl\;and\;2.3{\pm}0.1~15.7{\pm}0.8m/s.$ respectively, depending on the 15 possible combinations of 4-bit microheater array. We also experimentally characterize the effect of geometric variation including the microheater size, inter-microheater gap, microchannel width and sequential operation of microheater array on the ejected droplet volume and velocity. Among these parameters, we find that the microheater size is the most dominant parameter affected to the ejected droplet volumes and velocities. Thus, the present microinjector has a potential for application to the high-resolution inkjet printers with multiple gray levels or high-precision fluid injectors with variable volume control.

• Journal of Nuclear Fuel Cycle and Waste Technology(JNFCWT)
• /
• v.20 no.2
• /
• pp.243-253
• /
• 2022

Spent filters with a high radiation dose rate of 2 mSv·hr^-1 or more are not easily managed. So far, the Korean policy for spent filter disposal is to store them temporarily at nuclear power plants until the waste filters can be easily managed. Nuclear power plant decommissioning in Korea is starting with Kori unit 1. Volume reduction of waste generated during decommissioning can reduce the cost and optimize the space usage at disposal site. Therefore, efficient volume reduction is a very important factor during the decommissioning process. A conceptual method, based on the experiences of developing 200 and 800 ton compactors at Orion EnC, has been developed considering worker exposure with the followings a crusher (upgrade of compaction efficiency), an automatic dose measuring system with a NaI(Tl) detector, a shield box, an inner drum to prepare for easy handling of drums and packaging, a 30 ton compactor, and an automatic robot system. This system achieves a volume reduction ratio of up to 85.7%; hence, the system can reduce the disposal cost and waste volume. It can be applied to other types of wastes that are not easily managed due to high dose rates and remote control operation necessity.

• KIPS Transactions on Software and Data Engineering
• /
• v.5 no.12
• /
• pp.677-684
• /
• 2016

For realistic rendering volume to calculate the light effects as well as the shade is essential. In order to produce the high quality of the resulting image, it is necessary to represent a global illumination, and it should be considered an indirect effect of the direct impact and scattering of light. It requires a lot of resources in order to perform this operation and, in particular, is very expensive when large amounts of data to be rendered as a volume data is consumed. In this paper, we generate a scatterer template according to the physical laws for each material. Considering that each object having material property stores photons of the template based on the Lambert illumination model. When the volume rendering in this paper, using the photon is stored in the template, based on the voxel to be sampled within the examination volume occluded, and it represents the global illumination of the scattering. Because the materials produced by the template requires a less resource only if comprised of a complex material, a simple operation can be expressed within the scattering volume at a low cost through.

• Korean Journal of Optics and Photonics
• /
• v.8 no.3
• /
• pp.241-244
• /
• 1997

A speckle pattern from an optical fiber is used for a reference beam in writing and reading a volume hologram. The photorefractive volume hologram with this scheme shows good spatial selectivity for spatial(shift) multiplexing because the speckle pattern in writing and reading a hologram looses correlation with a small spatial shift. This scheme has the insensitivity to axial movement. The data storage system with this scheme will have a high storage density and a good stability in operation. We theoretically analyze the diffracted beam from a volume hologram recorded with the speckle pattern from the optical fiber. Experimental results are presented and compared with numerical analysis.

• The Korean Journal of Pain
• /
• v.8 no.1
• /
• pp.159-163
• /
• 1995

Accidental high epidural block is a rare but serious complication. It can result from many factors, which include the volume and concentration of drug, posture, puncture site, age, pregnancy or intra-abdominal mass, and patients' height and weight. We had a case of accidental high epidural block recently. This is a case report which was confirmed by an epiduragram. A healthy 50-year-old woman with a huge uterine myoma was scheduled for a total abdominal hysterectomy under continous epidural analgesia. Epidural catheterization was carried out smoothly. However, an unexpected hypotension was noticed after an epidural injection of 2% lidocaine 25 ml. Thereafter, the patient was intubated and her respiration was controlled during the operation. Using the 5mg of ephedrine, her blood pressure and pulse were well maintained. The scheduled operation was carried out for one hour uneventfully, but after the operation, she felt paresthesia on her hands in the recovery room. To differentiate between the high epidural and the subdural blocks. We injected 5 ml of a water soluble Niopam 300 through the catheter postoperatively. It was observed on the epiduragram that the catheter was placed in the epidural space. It was suggested that the high epidural block was induced from the widespread diffusion through the narrowed epidural space due to the engorgement of the epidural venous plexus by the patient's huge uterine myoma.