• Journal of the Institute of Electronics Engineers of Korea SD
• /
• v.38 no.11
• /
• pp.765-770
• /
• 2001

Metal-ferroelectric-insulator- semiconductor(MFTS) devices by using rapid thermal annealed (RTA) LiNbO$_3$/AIN/Si(100) structures were successfully fabricated and demonstrated nonvolatile memory operations. Metal-insulator-semiconductor(MIS) C-V properties with high dielectric AIN thin films showed no hysteresis and good interface properties. The dielectric constant of the AIN film calculated from the capacitance at the accumulation region in the capacitance-voltage(C-V) characteristics was about 8. The C-V characteristics of MFIS capacitor showed a hysteresis loop due to the ferroelectric nature of the LiNbO$_3$ thin films. Typical dielectric constant value of LiNbO$_3$ film of MFIS device was about 23. The memory window width was about 1.2 V at the gate voltage of $\pm$5 V ranges. Typical gate leakage current density of the MFIS structure was the order of 10$^{-9}$ A/$\textrm{cm}^2$ at the range of within $\pm$500 kV/cm. The ferroelectric capacitors showed no polarization degradation up to about 10$^{11}$ switching cycles when subjected to symmetric bipolar voltage pulse(peak-to-peak 8 V, 50 % duty cycle) in the 500 kHz.

• The Journal of the Korea institute of electronic communication sciences
• /
• v.16 no.1
• /
• pp.69-74
• /
• 2021

This paper introduces a low-power voltage-controlled oscillator(VCO) with filters that consist of resistors and capacitors. The proposed VCO contains a 5-stage current mode buffer, and each buffer cell has a resistor-capacitor filter that connects input and output terminals. The filter adds a zero to the buffer cell. Because the zero moves the oscillation condition to high frequencies, the proposed VCO can generate a high frequency clock with low power consumption. The proposed circuit has been designed with 0.18 ㎛ CMOS process. The power consumption is 9.83 mW at 2.7 GHz. The proposed VCO shows 3.64 pJ/Hz in our simulation study, whereas the conventional circuit shows 4.79 pJ/Hz, indicating that our VCO achieves 24% reduction in power consumption.

• Journal of Power Electronics
• /
• v.4 no.1
• /
• pp.46-55
• /
• 2004

This paper presents a high-frequency ZVS-PWM boost chopper-fed DC-DC converter with a single active auxiliary edge resonant snubber in the load-side which can be designed for power conditioners such as solar photovoltaic generation, fuel cell generation, battery and super capacitor energy storages. Its principle operation in steady-state is described in addition to a prototype setup. The experimental results of ZVS-PWM boost chopper-fed DC-DC converter proposed here, are evaluated and verified with a practical design model in terms of its switching voltage and current waveforms, the switching v-i trajectory, the temperature performance of IGBT module, the actual power conversion efficiency and the EMI of radiated and conducted emissions. And then discussed and compared with the hard switching scheme from an experimental point of view. Finally, this paper proposes a practical method to suppress parasitic oscillation due to the active auxiliary resonant switch at ZCS turn off mode transition with the aid of an additional lossless clamping diode loop, and reduced the EMI conducted emission in this paper.

• Journal of electromagnetic engineering and science
• /
• v.4 no.3
• /
• pp.137-142
• /
• 2004

In this paper, we present a new current-current negative feedback(CCNF) differential voltage-controlled oscillator (VCO) with 1/f induced low-frequency noise suppressed. By means of the CCNF, the 1/f induced low-frequency noise is removed from the proposed CCNF VCO. Also, high-frequency noise is stopped from being down-converted into phase noise by means of the increased output impedance through the CCNF and the feedback capacitor $C_f. The proposed CCNF VCO represents 11-dB reduction in phase noise at 10 kHz offset, compared with the conventional differential VCO. The phase noise of the proposed CCNF VCO is measured as - 87 dBc/Hz at 10 kHz offset frequency from 5.5-GHz carrier. The proposed CCNF VCO consumes 14.0 mA at 2.0 V supply voltage, and shows single-ended output power of - 12 dBm.

• Journal of Power Electronics
• /
• v.16 no.4
• /
• pp.1256-1267
• /
• 2016

Distributed stray inductance exerts a significant influence on the turn-off voltages of power switching devices. Therefore, the design of low stray inductance bus bars has become an important part of the design of high-power converters. In this study, we first analyze the operational principle and switching transient of a T-type converter. Then, we obtain the commutation circuit, categorize the stray inductance of the circuit, and study the influence of the different types of stray inductance on the turn-off voltages of switching devices. According to the current distribution of the commutation circuit, as well as the conditions for realizing laminated bus bars, we laminate the bus bar of the converter by integrating the practical structure of a capacitor bank and a power module. As a result, the stray inductance of the bus bar is reduced, and the stray inductance in the commutation circuit of the converter is reduced to more than half. Finally, a 10 kVA experimental prototype of a T-type converter is built to verify the effectiveness of the designed laminated bus bar in restraining the turn-off voltage spike of the switching devices in the converter.

• Proceedings of the KIEE Conference
• /
• 2003.10a
• /
• pp.186-188
• /
• 2003

The ZnO surge arrester is the protective device for limiting surge voltages on equipment by diverting surge current and returning the device to its original status. The occurrence of overvoltage appears in any phase to AC power supply system and it appears in mixing AC and impulse voltages, moreover because HVDC power supply system uses converter in semiconductor, it makes mixed DC and high harmonics voltages. In this study, the various mixed AC and DC voltages was made for investigating the degradation effect of ZnO arrester according to mixed voltage. As a result, the increase of DC component to mixed voltages causes the increase of resistive component of total leakage current to ZnO block. In changing V-I curve for mixed voltages, the cross-over point acts a factor as making the proper capacitor size of an equivalent circuit for ZnO block.

• Journal of Korea Society of Industrial Information Systems
• /
• v.22 no.2
• /
• pp.71-78
• /
• 2017

In This Paper, A DC-DC Boost Converter for Portable Device has been Proposed. The Converter Which is Operated with 1 MHz High Switching Frequency is Capable of Reducing Mounting Area of Passive Devices Such as Inductor and Capacitor, Consequently is Suitable for Portable Device. This Boost Converter Consists of a Power Stage and a Control Block and a Protect Block. Proposed DC-DC Boost Converter has been Designed a 0.18 um Magnachip CMOS Process Technology, we Examined Performances of the Fabricated Chip and Compared its Measured Results with SPICE Simulation Data. Simulation Results Show that the Output Voltage is 4.8 V in 3.3 V Input Voltage, Output Current 95 mA Which is Larger than 20~50 mA.

• Journal of Power Electronics
• /
• v.15 no.6
• /
• pp.1429-1437
• /
• 2015

A new parallel hybrid soft switching converter with low circulating current losses during the freewheeling state and a low output current ripple is presented in this paper. Two circuit modules are connected in parallel using the interleaved pulse-width modulation scheme to provide more power to the output load and to reduce the output current ripple. Each circuit module includes a three-level converter and a half-bridge converter sharing the same lagging-leg switches. A resonant capacitor is adopted on the primary side of the three-level converter to reduce the circulating current to zero in the freewheeling state. Thus, the high circulating current loss in conventional three-level converters is alleviated. A half-bridge converter is adopted to extend the ZVS range. Therefore, the lagging-leg switches can be turned on under zero voltage switching from light load to full load conditions. The secondary windings of the two converters are connected in series so that the rectified voltage is positive instead of zero during the freewheeling interval. Hence, the output inductance of the three-level converter can be reduced. The circuit configuration, operation principles and circuit characteristics are presented in detail. Experiments based on a 1920W prototype are provided to verify the effectiveness of the proposed converter.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2003.07b
• /
• pp.616-619
• /
• 2003

This work presents the design, fabrication and microwave performance of distributed analog phase shifter (DAPS) fabricated on $(Ba,\;Sr)TiO_3$ (BST) thin films for X-band applications. Ferroelectric BST thin films were deposited on MgO substrates by pulsed laser deposition. The DAPS consists of high impedance coplanar waveguide (CPW) and periodically loaded tunable BST interdigitated capacitors (IDC). In order to reduce the insertion loss of DAPS and to remove the alteration of unloaded CPW properties according to an applied dc bias voltage, BST layer under transmission lines were removed by photolithography and RF-ion milling. The measured results are in good agreement with the simulated results at the frequencies of interest. The measured differential phase shift based on BST thin films was $24^{\circ}$ and the insertion loss decreased from 1.1 dB to 0.7 dB with increasing the bias voltage from 0 to 40V at 10 GHz.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2004.11a
• /
• pp.207-209
• /
• 2004

Currently, for satisfying the needs of scaled MOSFET's a high quality thin oxide dielectric is desired because the properties of conventional $SiO_2$ film are not acceptable for these very small sized transistors. As an alternative gate dielectric have drawn considerable alternation due to their superior performance and reliability properties over conventional $SiO_2$, to obtain the superior characteristics of ultra thin dielectric films, $N_2O$ grown thin oxynitride has been proposed as a dielectric growtuanneal ambient. In this study the authors observed process characteristics of $N_2O$ grown thin dielectric. In view points of the process characteristics of MOS capacitor, the sheet resistance of 4.07$[\Omega/sq.]$, the film stress of $1.009e^{10}[dyne/cm^2]$, the threshold voltage$(V_t)$ of 0.39[V], the breakdown voltage(BV[V]) of 11.45[V] was measured in PMOS. I could achieve improved electrical characteristics and reliability for deep submicron MOSFET devices with $N_2O$ thin oxide.