• 한국표면공학회지
• /
• 제31권1호
• /
• pp.3-11
• /
• 1998

Molten Carbonate Fuel cell is a promising new type electric power generation system which can achieve high efficiency, lower matrrial cost and high operating temperature Making internal reforming possible. Although the development of the MCEC is progressing rapidly toward commercialization, two important tchological problems such as dissolution of NiO cathode and not corrosion of metallic separator plate must be resolved. Because MCFC is operated at $650^{\circ}C$ and the electrolyte is very corrosive, corrosion-resistance of separator plated against oxidation abd molten carbonate is required. Al-coating on separator material for corrosion-resistance was carried out by painting, thermal spraying. hot dipping and vacuum vapour deposition. The corrosion of Al-coated STS 316S and 316L in molten carbonate at $700^{\circ}C$was studied. Vacuum vapour deposition and thermal spraing for Al-coating on STS 310S and 316L were the most effective methods for protecting thestainless steel corrosion in molten carbonate.

• 한국수소및신에너지학회논문집
• /
• 제17권1호
• /
• pp.62-68
• /
• 2006

High temperature electrolysis is a promising technology to produce massively hydrogen using renewable and nuclear energy. Solid oxide fuel cell materials are candidates as the components of steam electrolysers. However, the polarization characteristics of the typical electrode materials during the electrolysis have not been intensively investigated. In this study, NiO electrode was deposited on YSZ electrolyte by spin coat process and firing at $1300^{\circ}C$. Pt electrode was applied on the other side of the electrolyte to compare the polarization characteristics with those by NiO during electrolysis. The $H_2$ evolution rate was also monitored by measuring the electromotive force of Lambda probe and calculated by thermodynamic consideration. At low current density, Pt showed lower cathodic polarization and thus higher current efficiency than Ni, but the oxidation of Ni into NiO caused the increase of anodic resistance with increasing current density. High overpotential induced high power consumption to produce hydrogen by electrolysis.

• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 2010년도 하계학술대회 논문집
• /
• pp.36-36
• /
• 2010

Currently, there are several newly developed energy resources for the future to replace petroleum resources such as hydrogen fuel cell, solar cell, wind power, and etc. Among them, solar cell has attracted a worldwide concern, because it has an enormous amount of resources. In general, a study of solar cells can be classified in to an area of bulk type and thin-film type. Inorganic solar cells based on silicon have been tremendously developed in technology and efficiency. However, since there are many lithographic steps, high processing temperature approximately $1000^{\circ}C$, and expensive raw materials, a manufacturing cost of device are nearly reaching a limit. Contrary to those disadvantages, organic solar cells can be manufactured at room temperature. Also, it has many advantages such as a low cost, easy fabrication of thin film, and possible manufacture to a large size. Because it can be made to be flexible, research and development on solar cells are actively in progress for the next generation. ever though an efficiency of the organic solar cell is low compared to that of inorganic one, a continuous study is needed. In this paper, we report optimal device structure obtained by a program simulation for design and development of highly efficient organic photovoltaic cells. we have also compared simulated results to experimental ones.

• 대한기계학회논문집B
• /
• 제40권12호
• /
• pp.793-799
• /
• 2016

폐열을 열원으로 사용하는 저온형 개질기는 하이브리드 연료전지 시스템의 효율향상을 위해 사용되고 있다. 저온형 개질기의 경우 저온의 열적상태에서 높은 열전달 효율을 내는 것이 중요하며, 이를 위한 형상 최적화의 과정이 필요하다. 본 연구에서는 제한된 열공급 상황에서 개질기의 형상인자 변화에 따른 온도 및 반응특성을 전산해석을 통하여 알아보고자 하였다. 해석결과 저온형 개질기의 반응이 활발히 일어나는 영역은 온도가 높은 후단에 제한되는 현상을 보여 고온형 개질기와의 차이를 나타내었다. 또한 개질기의 기체공간속도(Gas hourly space velocity, GHSV)를 감소시키거나 열전달 면적을 증대시킴으로써 효율을 향상 시킬 수 있음을 확인하였고 종횡비에 따른 해석을 실시한 결과 저온형 개질기의 경우 길이방향보다는 반경방향의 열전달을 증대시키는 방법이 효과적임을 확인하였다.

• 한국수소및신에너지학회논문집
• /
• 제22권4호
• /
• pp.474-480
• /
• 2011

Hydrocarbon is required to be converted to pure hydrogen without carbon monooxide (CO) for polymer exchange membran fuel cell (PEMFC) applications. In this paper, CO cleaning processes as the downstream of Dimethyl ehter (DME) autothermal reforming process were performed in micro-reactors. Our study suggested two kinds of water gas shift (WGS) reaction process: High Temperature shift (HTS) - Low Temperature shift (LTS), Middle temperature shift (MTS). Firstly, using perovskite catalyst for MTS was decreased effieiciency since methanation. Using HTS-LTS the CO concentration was decreased about 2% ($N_2$ & $H_2O$ free) with the reaction temperature of $420^{\circ}C$ and $235^{\circ}C$ for HTS and LTS, respectively. As the final stage of CO cleaning process, preferential oxidation (PROX) was applied. The amount of additional oxygen need 2 times of stoichiometric at $65^{\circ}C$. The total conversion reforming efficiency of 75% was gained.

• 한국수소및신에너지학회논문집
• /
• 제28권6호
• /
• pp.618-626
• /
• 2017

Conventional high temperature reformers are not suitable for hybrid fuel cell systems that use waste heat as a heat source. So, development of a low temperature type reformer is needed. However, the analysis was conducted in two ways to increase the thermal efficiency, because of low reforming rate due to the low heat source. First, it is a way to ger thermal gain from the outside through partial insulation. In the case of one heat source tube and several heat source tubes, we analyzed the effect of partial heat insulation in some cases. Second, we found the most efficient arrangement of the heat source tubes by changing the location of the heat source tubes. The interpretation was carred out using the COMSOL Mutiphysics program.

• 한국신재생에너지학회:학술대회논문집
• /
• 한국신재생에너지학회 2005년도 춘계학술대회
• /
• pp.339-344
• /
• 2005

A PEMFC system model for FCEV was constructed and simulated numerically to examine the heat/water flow of the system and air/fuel humidification process for various operation conditions (ambient pressure /temperature/humidity, operating temperature, power load). We modeled PEMFC stack which can generate maximum electricity of about 80 kW. This stack consists of 400 unit cells and each unit cell has $250cm^2$ reacting area. Uniform current density and uniform operating voltage per each cell was assumed. The results show the flow characteristics of heat and water at each component of PEMFC system in macro-scale. The capacity shortage of the radiator occurred when the ambient was hot $(over\;40^{\circ}C)$ and power level was high (over 50 kW). In spite of some heat release by evaporation of water in stack, heat unbalance reached to 20kW approximately in such a severe operating condition. This heat unbalance could be recovered by auxiliary radiators or high speed cooling fan with additional cost. In cold environment, the capacity of radiator exceeded the net heat generation to be released, which may cause a problem to drop the operating temperature of stack. We dealt with this problem by regulating mass flow rate of coolant and radiator fan speed. Finally, water balance was not easily broken when we retrieved condensed and/or unused water.

• 전기화학회지
• /
• 제3권1호
• /
• pp.44-48
• /
• 2000

상온에서 DC-magnetron sputtering으로 증착한 비정질의 $V_2O_5$ 박막을 양극물질로 하여 $V_2O_5/LIPON/Li$으로 구성된 박막형 리튬이차전지를 제작하였다. $V_2O_5$의 양극특성은 액체전해질을 이용한 half cell 구조에서 평가하였으며, $Ar/O_2$ 분압비의 변화에 따라 제작된 $V_2O_5$ 양극은 분압비 80/20에서 가장 좋은 특성을 보였다. 자체 제작한 $Li_3PO_4$ 타겟을 사용하여 RF-sputtering으로 순수한 질소 분위기 하에서 양극 위에 고체전해질 LIPON 박막을 형성하였으며, 1.2-4.0V vs. Li 구간에서 리튬에 대해 반응성이 없는 안정한 화합물임을 확인하였다. 음극으로 쓰인 약 $2{\mu}m$두께의 금속리튬박막은 진공 열 증착법으로 제조하였으며, $V_2O_5/LIPON/Li$의 박막형 리튬이차전지는 $1.2\~3.5V$ 구간에서 초기에 약 $150{\mu}A/cm^2{\mu}m$의 높은 방전용량을 나타내었다.

• 한국재료학회지
• /
• 제28권11호
• /
• pp.653-658
• /
• 2018

$ZrO_2$ is a candidate material for hip and knee joint replacements because of its excellent combination of biocompatibility, corrosion resistance and low density. However, the drawback of pure $ZrO_2$ is a low fracture toughness at room temperature. One of the most obvious tactics to cope with this problem is to fabricate a nanostructured composite material. Nanomaterials can be produced with improved mechanical properties(hardness and fracture toughness). The high-frequency induction heated sintering method takes advantage of simultaneously applying induced current and mechanical pressure during sintering. As a result, nanostructured materials can be achieved within very short time. In this study, W and $ZrO_2$ nanopowders are mechanochemically synthesized from $WO_3$ and Zr powders according to the reaction($WO_3+3/2Zr{\rightarrow}W+3/2ZrO_2$). The milled powders are then sintered using high-frequency induction heating within two minutes under the uniaxial pressure of 80MPa. The average fracture toughness and hardness of the nanostructured W-3/2 $ZrO_2$ composite sintered at $1300^{\circ}C$ are $540kg/mm^2$ and $5MPa{\cdot}m^{1/2}$, respectively. The fracture toughness of the composite is higher than that of monolithic $ZrO_2$. The phase and microstructure of the composite is also investigated by XRD and FE-SEM.

• 전기전자학회논문지
• /
• 제21권2호
• /
• pp.123-129
• /
• 2017

고분자 막 연료전지는 높은 전력밀도, 낮은 배출 및 낮은 동작온도 때문에 미래 자동차 및 전력생산의 강력한 보류이다. FEMFC 내부의 기체확산층(GDL)의 중요한 관심은 물의 조절이다. GDL은 소수성 PTFE와 전기전도성을 위해서 탄소로 보통 구성되어 있다. 이 시뮬레이션에서 GDL 흐름은 확립된 방정식 모델의 단순화된 접근법으로 조사되었다. GDL의 성능은 모델 방정식을 이용하여 전지의 내부열, 수증기 밀도 와 산소밀도의 결과를 보였다. FEMFC 촉매층 모델은 유효인자, Butler-volmer 와 수소유동 밀도의 결과를 나타냈다. 이 결과들은 몇 가지 요소들과 함께 영향의 차이는 흥미 가지게 되며 정보는 연료전지를 설계하는데 도움을 줄 것이다.