• 대한전기학회:학술대회논문집
• /
• 대한전기학회 2003년도 하계학술대회 논문집 B
• /
• pp.1151-1153
• /
• 2003

In this paper, switching surge voltage distribution in stator windings of induction motor driven by IGBT PWM inverter is studied. To analyze the irregular voltage of stator winding, equivalent circuit model of inverter-cable-motor was proposed and high frequency parameter is computed by using finite element method (FEM). Electromagnetic transient program (EMTP) analysis of the whole system for induction motor and PWM inverter is proposed. In order to experiment, an induction motor, 380 [V], 50 [HP], with taps from one phase and a switching surge generator was built to consider the voltage distribution.

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 1993년도 하계학술대회 논문집 B
• /
• pp.1159-1161
• /
• 1993

This paper may be presented the carrier oscillation properties for the varistor fabricated by a new method of three-composition seed grain, in order to analyze the behavior of carriers at the its equivalent circuit model. The oscillation phenomena of carriers appeared from current-voltage characteristics under knee voltage is shown by the transient flow of non trapped carriers group in the trap level of intergranular layer, surface state and/or depletion layer. However, Current oscillation phenomena is hardly shown in the high electric field. The injected carriers from both electrodes are directly flowed from the conduction band of forward biased grain through the intergranular layer into the reverse biased grain, because the trap level in the electric field above the knee voltage is mostly filled.

• 한국소음진동공학회:학술대회논문집
• /
• 한국소음진동공학회 2001년도 추계학술대회논문집 II
• /
• pp.739-744
• /
• 2001

In order to investigate the stability of magneto-rheological fluid based squeeze film damper (MR-SFD), its negative stiffness effect, which arises from magnetization of MR-SFD, is identified theoretically and experimentally. The analytical model of MR-SFD includes the magnetic circuit as well as the displacement stiffness associated with the squeeze mode of MRF. Extensive experiments are carried out to measure the magnetic attraction forces generated in the MR-SFD, with the excitation frequency and the eccentricity of the journal varied, which are controlled by an active magnetic bearing. The simulation and experimental results are found to be in good agreement. It is concluded that the negative stiffness effect dominates only in the low frequency region because its effect diminishes in the high frequency region due to the eddy-current loss.

• 대한기계학회:학술대회논문집
• /
• 대한기계학회 2004년도 추계학술대회
• /
• pp.447-452
• /
• 2004

Vacuum interrupters in order to be used in various switch-gear components such as circuit breakers, distribution switches, contactors, etc. spread the arc uniformly over the surface of the contacts. The electrodes of vacuum interrupters are made of sinter-forged Cu-Cr materials for good electrical and mechanical characteristics. Since the closing velocity is 1-2m/s and impact deformation of the electrode depends on the strain rate at that velocity, the dynamic behavior of the sinter-forged Cu-Cr is a key to investigate the impact characteristics of the electrodes. The dynamic response of the material at intermediate strain rate is obtained from the high speed tensile test machine test and at the high strain rate is obtained from the split Hopkinson pressure bar test. Experimental results from both quasi-static and dynamic compressive tests are interpolated to construct the Johnson-Cook model as the constitutive relation that should be applied to simulation of the dynamic behavior of the electrodes. The impact characteristics of a vacuum interrupter are investigated with computer simulations by changing the amount of chromium content.

• 조명전기설비학회논문지
• /
• 제19권1호
• /
• pp.130-135
• /
• 2005

일체형 코드에서는 접촉 불량, 기계적 충격 등의 부주의한 사용에 의해 전기화재가 자주발생하고 있다. 본 논문에서는 비닐코드 및 고무코드 등의 일체형 코드의 화재확산 패턴을 조사하기 위해 벽면모델을 모의하였다. 화재진행과 확산패턴은 고속카메라를 이용하여 측정하였다. 실험결과로부터, 일체형 코드의 화재패턴은 섬광, 비산 그리고 완전이탈 순으로 진행하였다. 외부화염에 의해 비닐코드가 고무코드보다 단락이 쉽게 발생하였다. 일체형 코드가 완전 이탈이 된 경우, 비닐코드는 착화에너지가 감소함에 따라 더 이상의 화재 진전은 이루어지지 않았지만, 고무코드는 연속적으로 화재가 진행하는 것을 알 수 있었다.

• 대한기계학회논문집B
• /
• 제24권1호
• /
• pp.21-28
• /
• 2000

Although commercial PIV systems have been widely used for the non-intrusive velocity field measurement of fluid flows, they are still under development and have considerable room for improvement. In this study, a single-frame double-exposure PIV system using a high-resolution CCD camera was developed. A pulsed Nd:Yag laser and high-resolution CCD camera were synchronized by a home-made control circuit. In order to resolve the directional ambiguity problem encountered in the single-frame PIV technique, the second particle image was genuinely shifted in the CCD sensor array during the time interval dt. The velocity vector field was determined by calculating the displacement vector at each interrogation window using cross-correlation with 50% overlapping. In order to check the effect of spatial resolution of CCD camera on the accuracy of PIV velocity field measurement, the developed PIV system with three different resolution modes of the CCD camera (512 ${\times}$ 512, lK ${\times}$ IK, 2K ${\times}$ 2K) was applied to a turbulent flow which simulate the Zn plating process of a steel strip. The experimental model consists of a snout and a moving belt. Aluminum flakes about $1{\mu}m$ diameter were used as scattering particles for the liquid flow in the zinc pot and the gas flow above the zinc surface was seeded with atomized olive oil with an average diameter of 1-$3{\mu}m$. Velocity field measurements were carried out at the strip speed $V_s$=1.0 m/s. The 2K ${\times}$ 2K high-resolution PIV technique was significantly superior compared to the smaller pixel resolution PIV system. For the cases of 512 ${\times}$ 512 and 1K ${\times}$ 1K pixel resolution PIV system, it was difficult to get accurate flow structure of viscous flow near the wall and small vortex structure in the region of large velocity gradient.

• 대한전자공학회논문지TC
• /
• 제48권9호
• /
• pp.47-53
• /
• 2011

본 논문에서는 커넥터의 특성임피던스 추출, 분석 방법 및 설계 변경 방법을 제안하고 임피던스를 정합하여 신호 전달 특성을 개선한다. 3차원 FEM(Finite Element Method) 전자기장(Electro-Magnetic Field) 시뮬레이터를 이용하여 커넥터의 S-파라미터를 계산하고 반사손실 및 삽입손실을 추출한다. 커넥터의 신호 전달 특성은 반사손실이 0.9 GHz 이후부터 -20 dB 이상의 값으로 높게 나타났다. 신호 전달 특성이 낮은 원인을 파악하기 위해서 회로 해석 시뮬레이터를 이용하여 커넥터의 등가 회로 모델을 추출하고 특성임피던스를 계산하였다. 커넥터의 특성임피던스는 $90.3{\Omega}$으로 임피던스 부정합이 발생하여 신호 전달 특성이 저하되었다. 따라서 신호 전달 특성을 개선할 목적으로 임피던스를 정합하기 위해서 커넥터의 커패시턴스를 증가시켰다. 이러한 설계 방안으로 커넥터 신호선의 유효 면적을 확장하고, 커넥터의 몸체 소재로 고유전체를 사용하였다. 설계 변경된 커넥터의 특성임피던스는 $58.6{\Omega}$으로 임피던스 정합에 보다 근접하여 커넥터의 반사손실이 대략 10 dB 향상되었다. 신호선의 유효 면적 증가에 의한 반사손실 개선과 고유전체의 적용으로 전자기파의 신호선 주변 집중에 의해서 삽입손실 또한 개선되었다.

• 반도체디스플레이기술학회지
• /
• 제20권3호
• /
• pp.71-76
• /
• 2021

Digital decimation filters are used in various digital signal processing systems using ADCs, including digital communication systems and sensor network systems. When the sampling rate of digital data is reduced, aliasing occurs. So, an anti-aliasing filter is necessary to suppress aliasing before down-sampling the data. Since the anti-aliasing filter has to have a sharp transition band between the passband and the stopband, the order of the filter is very high. However, as the order of the filter increases, the complexity and area of the filter increase, and more power is consumed. Therefore, in this paper, we propose two types of decimation filters, focusing on reducing the area of the hardware. In both cases, the complexity of the circuit is reduced by applying the required down-sampling rate in two times instead of at once. In addition, CIC decimation filters without a multiplier are used as the decimation filter of the first stage. The second stage is implemented using a CIC filter and a down sampler with an anti-aliasing filter, respectively. It is designed with Verilog-HDL and its function and implementation are validated using ModelSim and Quartus, respectively.

• 제어로봇시스템학회:학술대회논문집
• /
• 제어로봇시스템학회 1996년도 Proceedings of the Korea Automatic Control Conference, 11th (KACC); Pohang, Korea; 24-26 Oct. 1996
• /
• pp.259-262
• /
• 1996

This paper proposes an approach in modeling a 4x60inch Allis Chalmers Hydrocone Crusher [1] hydroset and presents some numerical simulation results. The mining and quarry industry is one of the industries which extensively use hydrocone crushers, which are a family of cone crushers, for rock size reduction. Field studies have proved that if proper control and management of these machines is undertaken, they can yield an increased production output of more than 30%, in addition substantial savings in both energy consumption per unit ton produced and manpower can be easily realized. In order to achieve these economic benefits, high performance from these machines is expected. Implementing automatic control for such machines would be a great leap towards achieving both economic benefits and more effective fool-proof predictive maintenance. But, unfortunately, for such a control system to be designed, it necessary to make a mechatronical model of this plant. The plant model is able to give us an insight into variations of both the plant gap setting (displacement) and system pressure due to variable loading arising from the crushing process.

• Journal of Magnetics
• /
• 제21권3호
• /
• pp.348-355
• /
• 2016

Precision motion stages used in the manufacturing process of flat-panel displays have inevitably low settling performance due to their huge mass and bulky structures. In order to improve the settling performance, several methods of frame vibration compensation have been developed so far. These methods are used to cancel the vibration by imposing a counter force or modifying the resonance mode of the frame of the stage. To compensate the frame vibration, high force actuators are required. In this paper, a mighty voice coil actuator is proposed to generate the counter force against the frame vibration. The proposed voice coil actuator has an axis-symmetric rectangular structure to achieve a large force with simple and low cost fabrication. Also, the voice coil actuator allows radial clearance up to ${\pm}4mm$. Using an optimized design process and a magnetic circuit model, the power consumption is minimized while the required force is obtained. With a power of 322 W, the VCA has been designed to have a maximum force of 574 N with a force constant of 164 N/A. Experimental results verified the force constant of the fabricated voice coil actuator is well matched with the designed value.