• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.23 no.11 s.170
• /
• pp.2050-2057
• /
• 1999

It is necessary to improve mechanical and optical properties in the optical disk substrates as the information storage devices with high storage density using short wavelength laser are being developed. Injection compression molding is regarded as the most suitable process to manufacture optical disk substrates with high dimensional accuracy, low residual stresses, and superb optical properties. In the present study, polycarbonate optical disk substrates were fabricated by injection compression molding and the birefringence, regarded as one of the most important optical properties for optical disk, is measured. The effects of various processing conditions upon the development of birefringence distribution were examined experimentally. It was found that the values of the birefringence distribution were very sensitive to the mold wall temperature history and the variance of the birefringence distribution in the radial direction was affected by the level of the packing and the compression pressure.

• Journal of ILASS-Korea
• /
• v.28 no.2
• /
• pp.89-96
• /
• 2023

This study presents a numerical simulation investigating hydrodynamic characteristics of high-temperature hydrocarbon aviation fuel injected through a plain orifice injector. The analysis encompassed the temperature range up to the critical point, and the obtained results were compared with prior experimental observations. The analysis unveiled that the injector's exit pressure remains equivalent to the ambient pressure when the fuel injection temperature is below the boiling point. However, when the fuel temperature surpasses the boiling point, the exit pressure of the injector transitions to the saturated vapor pressure corresponding to the fuel injection temperature. Consequently, the exit pressure of the injector increases in tandem with the rapid increase of the saturation vapor pressure due to escalating fuel temperatures. This rise in the exit pressure necessitates a proportional increase in fuel injection pressure to ensure a fixed fuel mass flow rate. Furthermore, the investigation revealed that the discharge coefficient obtained by applying the exit pressure instead of the ambient pressure did exhibit no decrease, but rather was maintained at a nearly constant value, comparable to its level below the boiling point.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 2006.05a
• /
• pp.575-576
• /
• 2006

Recently, the demand of high-productivity injection mold increases since the consumption of packaging grows in the world. Stack mold is composed of more than two molds and it has very high productivity and economic efficiency. In advanced country, stack mold which has $4Level{\times}96cavity$ was developed already but, in occasion of domestic mold industry, there is no study of stack mold. In this study, stack mold which has $2Level{\times}4cavity$ is developed for securing the technique of manufacturing high-productivity mold.

• Journal of the Korean Society of Laryngology, Phoniatrics and Logopedics
• /
• v.25 no.2
• /
• pp.96-98
• /
• 2014

Injection laryngoplasty is simple and useful procedure in patient with vocal cord paralysis even under local anesthesia. For approaching vocal cord level, flexibility of neck mobility is required to operate injection laryngoplasty but it is relatively difficult to approach vocal cord in patient who has cervical fixations. Laryngeal mask airway (LMA) can be helpful:We use a LMA (I-gel$^{TM}$) during intubation without neck extension on flat supine position under general anesthesia and have a good operation filed. LMA with swivel connector give surgeons better surgical vision and make insertion of fibroscope easily during operation. Hyaluronic acid injection was done use needle (25 G, 5 cm) via percutaneous cricothyroid space : This procedure can be useful method for patients who suffer from not only weak voice but also dysphagia and aspiration high vagal palsy patient after spine surgery or uncooperative with awake injection laryngoplasty.

• The Journal of Engineering Geology
• /
• v.31 no.4
• /
• pp.589-601
• /
• 2021

Artificial recharge technology is a method for solving problems such as groundwater level drop and ground subsidence caused by groundwater withdrawal. This study investigated the applicability of using the hydraulic conductivity of an aquifer to predict injection test results for aquifer restoration. Pumping and injection tests were performed under the same conditions as those for the artificial injection facility located in Icheon, Gyeonggi-do. The hydraulic conductivity of the aquifer, which plays a decisive role in restoring the groundwater level, was derived from the pumping test. A numerical model of a simplified on-site aquifer was constructed, and a transient analysis was applied with the same conditions as the pumping test. The correlation between the measured and the resulting model values is strong (R² = 0.78). The injection test was performed in a sedimentary layer composed of silt sand and clay sand. From the results of the injection test, an empirical formula was derived using Theim's formula, which is a common well analysis solution to determine the parameters of the aquifer from time-level data. The model values from the empirical formula have a high degree of correlation (R² = 0.99) with measured values. Under specific conditions, for areas where it is difficult to conduct an injection test, the formula from this study, which relies on the hydraulic conductivity of the aquifer determined through the pumping test, may be used to predict reliable injection rates for groundwater restoration.

• Transactions of the Korean Society of Mechanical Engineers B
• /
• v.36 no.7
• /
• pp.759-765
• /
• 2012

This study investigates the effect of diesel combustion strategies on exhaust emissions and hydrocarbon species emissions for a 1.7 L common rail direct injection diesel engine at 1500 rpm and 3.9 bar BMEP. The first strategy is a method to adopt no EGR with a split injection composed of pilot and main injection (split injection). The second is to adopt a moderate EGR rate with main injection only (single-1). The third is to use a high level of EGR and main injection with rail pressure increase, $i.e.$ low-temperature diesel combustion (single-2). Split injection and single-1 showed a renowned phenomenon of a PM-NOx trade-off, whereas single-2 was observed of a PM-NOx trade-off to reduce PM and NOx simultaneously. HC speciation results show that the split injection produced the least amount of HC species, regardless of the carbon number bin, followed by single-1 and single-2. The ratios of methane, acetylene, and CO to THC increased as a combustion A/F ratio is richer due to reduced oxygen content in the vicinity of the combustion zone, thus enhancing pyrolysis.

• Journal of the Institute of Electronics Engineers of Korea SD
• /
• v.39 no.3
• /
• pp.9-19
• /
• 2002

By using the thermionic emission model, the L-I-V(power-current-voltage) characteristics of a SCH(seperate confinement heterostructure) QW(quantum well) laser diode is analytically derived. We derived the relationships between the bulk carrier density of SCH regions and the confined carrier density of QW. The L-I-V characteristics is derived analytically by using current continuity equations. Solving the ambipolar diffusion equation under the condition of high level injection and charge neutrality, the current distribution in the SCH regions is considered. Results showed that the major factor affecting the laser I-V characteristics was the change of potential barrier at the cladding-SCH interface. Also the series resistance of a laser diode was decreased and the carrier injection was increased by increasing the forward flux of injection current from cladding to SCH region.

• Design & Manufacturing
• /
• v.11 no.2
• /
• pp.9-14
• /
• 2017

The design and manufacturing tehcnology of IC sockets beyond 0.3mm pitch were presented. We compared the developed IC socket with the conventional one especially on the core metal-insulation part. Advanced machining techniques were employed to provide high precision. Our wire electrodischarge machining and high speed machining centers were able to maintain the micro-scale precision. We performed an injection molding analysis using a commercial analysis tool to predict the performance of the developed IC socket. We found that the solidification of the plastic resin and the high level of the clamping force are responsible for the defects such as incomplete filling and short shot. From these results, we modified the IC socket and successfully remove the defects. We were also able to find out that the new design socket needs less maintenance cost.

• International Journal of Computer Science & Network Security
• /
• v.23 no.2
• /
• pp.199-202
• /
• 2023

Carriage return (CR) and line feed (LF), also known as CRLF injection is a type of vulnerability that allows a hacker to enter special characters into a web application, altering its operation or confusing the administrator. Log poisoning and HTTP response splitting are two prominent harmful uses of this technique. Additionally, CRLF injection can be used by an attacker to exploit other vulnerabilities, such as cross-site scripting (XSS). Email injection, also known as email header injection, is another way that can be used to modify the behavior of emails. The Open Web Application Security Project (OWASP) is an organization that studies vulnerabilities and ranks them based on their level of risk. According to OWASP, CRLF vulnerabilities are among the top 10 vulnerabilities and are a type of injection attack. Automated testing can help to quickly identify CRLF vulnerabilities, and is particularly useful for companies to test their applications before releasing them. However, CRLF vulnerabilities can also lead to the discovery of other high-risk vulnerabilities, and it fosters a better approach to mitigate CRLF vulnerabilities in the early stage and help secure applications against known vulnerabilities. Although there has been a significant amount of research on other types of injection attacks, such as Structure Query Language Injection (SQL Injection). There has been less research on CRLF vulnerabilities and how to detect them with automated testing. There is room for further research to be done on this subject matter in order to develop creative solutions to problems. It will also help to reduce false positive alerts by checking the header response of each request. Security automation is an important issue for companies trying to protect themselves against security threats. Automated alerts from security systems can provide a quicker and more accurate understanding of potential vulnerabilities and can help to reduce false positive alerts. Despite the extensive research on various types of vulnerabilities in web applications, CRLF vulnerabilities have only recently been included in the research. Utilizing automated testing as a recurring task can assist companies in receiving consistent updates about their systems and enhance their security.

• Journal of the Korean Institute of Telematics and Electronics B
• /
• v.30B no.1
• /
• pp.38-44
• /
• 1993

A model for BICMOS buffer switching operation is presented, including the influence of bipolar base transit time and collector-base capacitances. A closed-form solution for the propagation delay-time is obtained assuming low level injection and channel velocity limitation. For the high level injection case, the delay-times are numerically obtained using effective current gain. These results are compared with those by HSPICE simulation, which shows good agreement. It is noted that the collector-base capacitance strongly affects the delay-time. The effects of voltage scaling are also investigated, which shows the model can be applied for the reduced supply voltages.