• Journal of IKEEE
• /
• v.14 no.3
• /
• pp.173-181
• /
• 2010

The high flowability performance evaluation device for the concrete is the device which was designed to compensate from the incorrect data detection of the viscosimetry examination of the existing concrete. As for the existing concrete viscosimetry method, the measuring data for a viscosity are very irregular by the point of view of an experimenter and a supervisor, Therefore there were some problems to have many different opinions by a small numerical value difference according to the job characteristic. In this paper, we suggested some mechanism to compensate the problem and some driving electronics including the related algorithm, and the communication structure with wireless sensor network between the devices and users are also presented. The effectiveness of the suggested method was verified with a real experiment.

• Proceedings of the Korea Concrete Institute Conference
• /
• 1999.10a
• /
• pp.267-270
• /
• 1999

In this paper, the application of limestone powder, which produced by being gathered electrically in the process of manufacturing of cement, to high fluidity concrete are investigated. According to the experimental results, especially, high viscosity and the loss of air content are accomplished by applying limestone powder as the partial substitution of fine aggregates. In case of hardened concrete, high compressive strength can be achieved by using limestone powder.

• Proceedings of the Korean Society of Tribologists and Lubrication Engineers Conference
• /
• 2002.10b
• /
• pp.347-348
• /
• 2002

The numbers of synthetic greases have been developed with synthetic oils because of their excellent performance factors including thermal/oxidation stability, low-temperature fluidity and plastic compatibility. Long life under high-temperature condition and excellent low-temperature fluidity are required to serve as grease for bearings of engine room electrical component. As many plastics are used in place of metals for the purpose of weight saving, synthetic hydrocarbon grease is in use to avoid adverse effect on plastics. Other various special synthetic greases are also in use depending on specific requirements like conductivity and vacuum condition.

• Proceedings of the Korea Concrete Institute Conference
• /
• 2006.05b
• /
• pp.473-476
• /
• 2006

As a part of efforts to obtain high quality and economical efficiency of concrete, blast-furnace slag has been utilized by means of cement replacement. Therefore superior performance can be ensured, environmental pollution can be prevented and economical advantage can be obtained with utilization by cement replacement. But the studies on the blast-furnace slag are not systematic and reasonable. So, it was planed that basic data in regard to technique of manufacturing and economic improvement of concrete is showed with experimental comparison and investigation of Fluidity and engineering properties of concrete utilizing blast-furnace, industry by-product, as cement replacement in this study.

• Journal of the Korean Ceramic Society
• /
• v.46 no.6
• /
• pp.657-661
• /
• 2009

In this study, rheological properties of cement pastes containing ground Finex-slag (4000, 6000, 7000 c$m^2$/g) were investigated bymini-flow test and coaxial cylinder viscometer. And also blast furnace slag(4000, 6000, 7000 c$m^2$/g) were used for comparison. According to the experimental results, Finex-slag and blast furnace slag showed very similar trend in the rheological properties of the cement pastes. The fluidity of cement pastes blended Finex-slag and blast furnace slag powder were improved by high replacement ratio. In the relationship of plastic viscosity and yield stress appeared the tendency of the proportion greatly. And in the relationship of plastic viscosity, yield stress and mini-flow appeared the tendency of the inverse proportion.

• Textile Coloration and Finishing
• /
• v.24 no.1
• /
• pp.62-68
• /
• 2012

Cellulose was electrospun over water collector and the cellulose solution was prepared using N-methyl-morpholine N-oxide/water(nNMMO/$H_2O$). The morphology of electrospun cellulose was investigated by scanning electron microscopy (SEM). SEM images showed that the fiber formation depended on processing parameters such as solution concentration, applied electric field strength, solution feeding rate and temperature of water in coagulation bath. High concentration, low temperature of water bath, and low feeding rate were more favorable to obtain fiber morphology. All the variables affected on the fluidity of the cellulose solution and diffusion of NMMO. Low fluidity and fast diffuision of NMMO was critical for obtaining fiber morphology.

• Proceedings of the Korean Institute of Building Construction Conference
• /
• 2003.05a
• /
• pp.81-87
• /
• 2003

The purpose of this study is the development of a recycling process to recover the hydrated ability of cement hydrate which accounts for a large proportion of cementitious powder by concrete waste in order to recycle cementitious powder by concrete waste as recycle cement. Therefore, after having theoretical consideration based on the properties of high-heated concrete, we consider the properties of hydration of cementitious powder in hardened mortar under various temperature conditions. As a result of experiment, it is revealed that an effective development of recycling cement is possible since the cementitious powder by concrete waste recovers a hydraulic property during burning at $600^{\circ}C$ or $700^{\circ}C$. And it is shown that the fluidity of mortar decreases rapidly as the burning temperature of recycle cement increases. however, the improved effect of fluidity is predominant if adding the additive such as fly-ash or blast furnace slag.

• Proceedings of the Korean Powder Metallurgy Institute Conference
• /
• 2006.09b
• /
• pp.759-760
• /
• 2006

Ti-6Al-4V has low specific gravity, high corrosion resistance and superior mechanical properties but it is very difficult to control oxygen content in MIM process. It is necessary to use powders with coarse particle size to decrease oxygen content of powders, so feedstocks with poor fluidity and sintered bodies with lower density are obtained in such cases. Fine titanium hydride-dehydride powders were blended with atomized powders to accomplish higher fluidity and sintered density. Sintered bodies had higher sintered density and mechanical properties equivalent to those of wrought materials by controlling oxygen content less than 0.35mass%.

• Journal of Korea Foundry Society
• /
• v.35 no.6
• /
• pp.141-146
• /
• 2015

Aluminum-based hybrid parts were fabricated through a compound casting process with Al or Cu inserts which can be used for applications requiring high conductivity. Because the interface stability between the insert and the aluminum matrix is important, the effects of process variables on the interfacial adhesion strength were investigated. Additions of Cu and Mg to Al melt were found to enhance the adhesion strength, though the melt fluidity was slightly deteriorated when a small amount of Mg was added. An isothermal heating process after casting further improved the strength. However AlCu intermetallic compounds formed and their thickness increased during the heating process. As a result, deterioration in the interfacial adhesion strength was observed after an excessive annealing treatment.

• Proceedings of the Korea Concrete Institute Conference
• /
• 2006.11a
• /
• pp.437-440
• /
• 2006

Generally, the strength of concrete depends on factors of materials, mix proportions, compaction, manufacturing methods and curing and so on. And recently, it has increased the using of crushed sand for concrete due to the exhaustion of good natural aggregate. This is an experimental study to compare and analyze the fluidity and compressive strength of ultra-high strength concrete according to the replacement ratio of crushed sand. For this purpose, the mix proportions of concrete according to the W/B ratio and replacement ratio of crushed sand was selected. And then air content, slump-flow, O-lot, compressive strength test were performed.