• 대한기계학회논문집A
• /
• 제24권5호
• /
• pp.1238-1245
• /
• 2000

One of the main causes of severe wear or crack initiation in wheel and rail is the contact stress due to wheel-rail contact. First, we obtain contact stress due to the rail mounting slope using the finite element method. Second, the shape design based on more reasonable contact stress analysis rather th~n a general Hertzian contact theory is investigated in order to reduce the contact stress. The optimum -design is performed using the simple 2-D finite element model and its results are verified by 311) finite element analysis.

• 대한기계학회논문집A
• /
• 제23권11호
• /
• pp.2033-2039
• /
• 1999

One of the main causes of severe wear or crack initiation in wheel and rail is the contact stress due to wheel-rail contact. In this paper, the shape design based on more reasonable contact stress analysis rather than a general Hertzian contact theory is investigated in order to reduce the contact stress. The optimal design is performed using the simple 2-D finite element model and its results are verified by 3-D finite element analysis.

• 대한기계학회논문집A
• /
• 제33권1호
• /
• pp.82-88
• /
• 2009

A disadvantage in the design of gerotor pump is a lack of parts that can be adjusted to compensate for wear in the rotor set, and as a consequence, it causes a sharp reduction of efficiency. In this paper, an attempt has been made to reduce the wear rate between the rotors of a gerotor pump. To do this, floating genetic algorithm (FGA) is used as an optimization technique for minimizing the wear rate proportional factor (WRPF). The result shows that the wear rate can be reduced considerably, e.g. approximately 8% in this paper, throughout the optimization using FGA.

• 한국정밀공학회지
• /
• 제27권3호
• /
• pp.80-88
• /
• 2010

A simple computational model for modeling of subsurface crack growth under cyclic contact loading is presented. In this model, it is assumed that the initial fatigue crack will initiate in the region of the maximum equivalent stress at certain depth under the contacting surface. The position and magnitude of the maximum equivalent stress are determined by using the equivalent contact model, which is based on the Hertzian contact conditions with frictional forces. The virtual crack extension method is used for simulation of the fatigue crack growth from the initial crack up to the formation of the surface pit due to contact fatigue. The relationships between the stress intensity factor and crack length are then determined for various combinations of equivalent contact radii and loadings.

• 한국소음진동공학회:학술대회논문집
• /
• 한국소음진동공학회 2001년도 추계학술대회논문집 I
• /
• pp.341-348
• /
• 2001

In this study, nonlinear vibration analysis of the cylindrical orthotropic porous thin plate under V-shaped tension distribution with wire impact damping is considered. We make dynamic model of the plate under the tension using commercial FEM code and reduce the number of its degrees of freedom using dynamic condensation. The dynamic model of wire is obtained as lumped mass model from string equation. And then we analyze the nonlinear vibration of the plate including the impact phenomenon between the plate and the wire using the reduced mass and stiffness matrices of the plate and lumped model of the wire. The contact phenomenon between them can be described by impact contact elements composed of contact stiffness coefficients from Hertzian contact theory and contact damping coefficients from restitution coefficient between them. And we discussed the results of nonlinear vibration analysis for variations of their design parameters.

• 소음진동
• /
• 제8권4호
• /
• pp.616-622
• /
• 1998

An analytical method has been developed to estimate the dynamic contact force between wheel and rail when trains are running on rail with vertical irregularities. In this method, the effect of Hertzian deformation at the contact point is considered as a linearized spring and the wheel is considered as an sprung mass. The rail is modelled as a discretely-supported Timoshenko beam, and the periodic structure theory was adopted to obtain the driving-point receptance. As an example, the dynamic contact force for a typical wheel/rail system was analysed by the method developed in this research and the dynamic characteristics of the system was also discussed. It is revealed that discretely-supported Timoshenko beam model should be used instead of the previously used continuously-supported model or discretelysupported Euler beam model, for the frequency range above several hundred hertz.

• 한국윤활학회:학술대회논문집
• /
• 한국윤활학회 1998년도 제28회 추계학술대회
• /
• pp.212-218
• /
• 1998

This paper presents a study of the elastohydrodynamic lubrication of elliptical contacts where lubricant entrainment coincides with the major axis of the Hertzian contact ellipse. A finite difference method and the Newton-Raphson method are applied to analyze the problem. Film contours and pressure distributions are compared with the results for lubricant entrainment coincides with the minor axis. Variations of the minimum and central film thicknesses with the radius ratio are also examined. Therefore, the present numerical scheme can be used generally in the analysis of the EHL of elliptical contacts where the lubricant entraining vector did not coincide with either of the principal axis of the conjunction.

• 한국윤활학회:학술대회논문집
• /
• 한국윤활학회 1997년도 제26회 추계학술대회
• /
• pp.100-109
• /
• 1997

Tappet is the part which consists of valve train system in Over Head Valve type diesel engine. The role of tappet is to open and close the intake/exhaust valve by rotating with cam. There are wear problems like scuffing or pitting in cam/tappet system because of the higher Hertzian contact stress and sliding wear characteristics between cam and tappet. In this paper, to find optimal materials combination in cam/tappet system, wear test and rig test were performed. $Si_3N_4$, chilled cast iron, sintered alloy were selected for tappet materials. As the result of test, it is found that $Si_3N_4$ tappet has the excellent wear properties.

• Tribology and Lubricants
• /
• 제10권3호
• /
• pp.71-77
• /
• 1994

Rolling friction test was carried out to investigate the effect of the wear amount on rolling contact fatigue process in lubrication oil. The methods of this process were conducted at two Hertzian contact pressure and three slide ratio in each case by employing normalized and annealed carbon steel. During process of the rolling contact fatigue, the number of rotation until surface damage was occurred, the wear amount of rolling contact surface, and residual stress and half-value breadth using X-ray reflection on rolling contact surface were investigated. The result of this study shows that rolling contact fatigue process was directly influenced by wear trend and was confirmed by change of residual stress and half-value breadth on rolling contact surface.

• Tribology and Lubricants
• /
• 제17권1호
• /
• pp.33-39
• /
• 2001

A method of calculating wear volume is developed using the signal processing technique. The lowpass filter with Fourier transform and the “windowing” are implemented in the method. User-defining feature is also included in determining the cutoff frequency of the low-pass filter and the baseline for the volume integration. Commercial software, MatLab, is used for the programming. Since the method uses the original wear data without simplifying the wear shape, it can give a further accurate result than the previously utilized methods, which often adopted the simplification. It becomes further powerful if the contacting body has a general shape rather than that gives well-formed surface traction (e.g., the Hertzian). The validation of applying the average surface roughness, Ra, to the “windowing” and the baseline for volume integration is discussed.