• 한국항공우주학회지
• /
• 제33권9호
• /
• pp.9-15
• /
• 2005

국방과학연구소 풍동실험실에서는 회전익 항공기 개발에 소요되는 관련 풍동시험 기법의 확립과 형상연구 관련 시험자료의 확보를 위한 실험적 연구를 수행하였다. 본 연구는 회전익 항공기 동체구성품의 형상조합에 따른 항력증분과 안정성 평가를 위한 공기역학적 특성의 추출을 목적으로 하였으며, 풍동시험에는 모듈화된 1:8 축척의 회전익 항공기 동체형상과 500 rpm으로 회전하는 로터허브의 부분모형이 사용되었다. 시험결과들을 기존의 유사 항공기 시험결과들과 비교하였으며, 기존 연구결과들과 잘 부합됨을 확인하였다.

• 항공우주산업기술동향
• /
• 제9권1호
• /
• pp.77-89
• /
• 2011

헬리콥터는회전하는구동시스템에의해추력및비행제어력을발생하기때문에회전체에서기체로전달되는 진동 및 소음을 줄이는 것이 아주 중요하다. 과거에는 수동적 방법으로 특정주파수에 해당하는 진동 및 소음을 줄였지만, 기술이 발달함에 따라 주파수를 변동시킬 수 있는 장치를 적용할 수 있는 능동적 진동 및 소음 제어방법이 개발되었다. 본 논문에서는 이러한 헬리콥터 진동 및 소음을 제어하는 능동적 방법에 대한 세계적인 기술동향 및 사례를 기술하였다. 서론에서는 헬리콥터 진동 및 소음을 제어하는 일반적인 방법론을 소개하고, 본론에서는 능동적으로 제어하는 사례 및 동향을 중심으로 기술하였다. 현재 가장 활발하게 진행되고 있는 능동적 플랩구동장치 및 비틀림장치 등을 중심으로 소개하였다.

• Advances in aircraft and spacecraft science
• /
• 제3권3호
• /
• pp.271-298
• /
• 2016

In this paper, we study a problem of passive suppression of helicopter Ground Resonance (GR) using a single degree freedom Nonlinear Energy Sink (NES), GR is a dynamic instability involving the coupling of the blades motion in the rotational plane (i.e. the lag motion) and the helicopter fuselage motion. A reduced linear system reproducing GR instability is used. It is obtained using successively Coleman transformation and binormal transformation. The analysis of the steadystate responses of this model is performed when a NES is attached on the helicopter fuselage. The NES involves an essential cubic restoring force and a linear damping force. The analysis is achieved applying complexification-averaging method. The resulting slow-flow model is finally analyzed using multiple scale approach. Four steady-state responses corresponding to complete suppression, partial suppression through strongly modulated response, partial suppression through periodic response and no suppression of the GR are highlighted. An algorithm based on simple criterions is developed to predict these steady-state response regimes. Numerical simulations of the complete system confirm this analysis of the slow-flow dynamics. A parametric analysis of the influence of the NES damping coefficient and the rotor speed on the response regime is finally proposed.

• 제어로봇시스템학회논문지
• /
• 제20권11호
• /
• pp.1103-1111
• /
• 2014

The results of control law design for a tilt-rotor unmanned aerial vehicle that has a nacelle mounted wing extension (WE) are presented in this paper. It consists of a control surface mixer, stability and control augmentation system (SCAS), hold mode for altitude / speed / heading, and a guidance mode for preprogram and point navigation which includes automatic take-off and landing. The conversion corridor and the control moments derivatives between the original tilt-rotor and its variant of the nacelle mounted WE were compared to show the effectiveness of the WE. The nacelle conversion of the original tilt-rotor starts when the airspeed is greater than 30 km/h but its WE variant starts at 0 km/h in order to reduce the drag caused by the high incidence angle of the WE. The stability margins of the inner loop are presented with the optimization approach. The outer loops for the hold mode are designed with trial and error methods with linear and nonlinear simulation. The main control parameter for altitude control of the helicopter mode is thrust command and it is transferred to the pitch attitude command in airplane mode. Otherwise, the control parameter for the speed of the helicopter mode is the pitch attitude command and it is transferred to the thrust command in airplane mode. Therefore the speed and altitude hold mode are coupled to each other and are engaged at the same time when an internal pilot engages any of the altitude or speed hold modes. The nonlinear simulation results of the guidance control for the preprogrammed mode and point navigation are also presented including automatic take-off and landing in order to prove the full control law.

• International Journal of Aeronautical and Space Sciences
• /
• 제8권1호
• /
• pp.66-78
• /
• 2007

A multi-point aerodynamic shape optimization technique has been developed for helicopter rotor blades in hover based on a continuous adjoint method on unstructured meshes. The Euler flow solver and the continuous adjoint sensitivity analysis were formulated on the rotating frame of reference. The 'objective function and the sensitivity were obtained as a weighted sum of the values at each design point. The blade section contour was modified by using the Hicks-Henne shape functions. The mesh movement due to the blade geometry change was achieved by using a spring analogy. In order to handle the repeated evaluation of the design cycle efficiently, the flow and adjoint solvers were parallelized based on a domain decomposition strategy. A solution-adaptive mesh refinement technique was adopted for the accurate capturing of the wake. Applications were made to the aerodynamic shape optimization of the Caradonna-Tung rotor blades and the UH-60 rotor blades in hover.

• 한국소음진동공학회:학술대회논문집
• /
• 한국소음진동공학회 2012년도 추계학술대회 논문집
• /
• pp.190-195
• /
• 2012

Small-scaled Rotor Test facility(GSRTS, General Small-scaled Rotor Test Facility) in KARI could not use the test because facility aging and parts discontinued. Also in order to perform a joint international research, GSRTS modifications should be needed. So requirements of GSRTS modifications were established and according to the requirements, GSRTS modifications were conducted. Facility operation test, 6-component fixed balance calibration, Small-scaled OLS rotor performance test were performed to verify the results of GSRTS modifications. Reasonable results were obtained in comparison to calculation results. Then GSRTS ready was completed to conduct international collaborative research and wind tunnel test.

• 한국항공운항학회지
• /
• 제15권3호
• /
• pp.6-14
• /
• 2007

In this research, vibration reduction and aeroelastic stability of a composite hingeless rotor hub flexure with viscoelastic constrained layer damping treatment(CLDT) were investigated. The composite flexures with viscoelastic CLDT were applied to hingeless rotor system to improve the in-plane stability of the lead-lag motion causing resonance. The modal test was performed and dynamic properties(natural frequency and loss factor) were acquired. Also, complex eigenvalue analysis(SOLlO7) in the NASTRAN structural analysis module was performed and compared with results of the modal test. To insure aeroelastic stability, damping ratio analyses of the hingeless rotor system with CLDT were accomplished at hovering condition due to collective pitch angle changes. Satisfactory results of increasing structural damping and stability were obtained.

• 소음진동
• /
• 제5권2호
• /
• pp.215-224
• /
• 1995

In this paper, the three-dimensional finite element model is established to investigate the structural dynamic characteristics of rotor blade using a finite element analysis. Six natural frequencies and mode shapes are calculated by computer simulation. The first three flapping modal frequencies, the first two lead-lag modal frequencies, and the first feathering modal frequency are validated through comparison with the modal test results of the fixed rotor blade. The computer simulation results are found in good agreement with experimentally measured natural frequencies. The important results are obtained as follows: (1) Natural frequencies are changed due to the variation of rotational speed and fiber angle of rotor blade, (2) Weak coupling between flapping mode shape and lead-lag mode shape are detected, (3) Centrifugal force has more effect on flapping modal frequency than lead-lag modal frequency.

• 항공우주시스템공학회지
• /
• 제3권3호
• /
• pp.17-23
• /
• 2009

KARI SUAV (Smart Unmanned Aerial Vehicle) program is currently on the phase of ground and flight test. SUAV is a tilt rotor aircraft having the capability of vertical take-off/landing and high speed forward flight. The SUAV rotor system is 3-bladed, gimbaled hub type, which is not common for conventional helicopter configuration. In this paper, detailed procedure and method of rotor pitch rigging, tracking and balancing were described based on the experience of SUAV ground test.

• 한국복합재료학회:학술대회논문집
• /
• 한국복합재료학회 2002년도 춘계학술발표대회 논문집
• /
• pp.173-176
• /
• 2002

This paper describes the design procedure of composite parts for hingeless hub system of helicopter. These composite parts are composed of flexure and sleeve. The design of this composite flexure is an important technique in hingeless hub system since the rotor system stability and dynamic characteristics depends on this flexure characteristics. The objective of this research is to replace the existing metal hub parts with composite to improve the performance and stability. First, the coupon test of candidate composite material for hub parts was conducted. The hub parts was designed based on test results and the manufacturing possibility by using Fiber Placement System(FPS) was checked. Also the dynamic analysis and stress analysis of composite hub parts was conducted. Through this research, we will find out the possibility of replacing existing metal hub parts with composite.