• Journal of Environmental Science International
• /
• v.6 no.3
• /
• pp.267-276
• /
• 1997

It has been studded that combustion and the production of air pollution of anthracite - bituminous coal blend In a fluidized bed coal combustor, The objects of thIns study were to investigate mixing characteristics of the particles as well as the combustibility of the low grade domestic anthracite coal and Imported h19h calorific bltununous coal in the fluidized bed coal combustor. They were used as coal samples ; the domestic low grade anthracite coal with heating value of 2,010kca1/kg and the Imported high grade bituminous coal with beating value of 6,520kca1/kg. Also, the effects of air flow rate and anthracite fraction on the reaching time of steady state condition have been studied. The experimental results are presented as follows. The time of reaching to steady state was affected by the temperature variation. The steady state time was about 120 minute at 300sc1h which was the fastest. It has been found that $O^2$ and $CO^2$ concentration were reached steady state at about 100 minute. It has been found that $O^2$ concentration decreased and $CO^2$ concentration increased as the height of fluidlzed bed Increased. It was found that splash zone was mainly located from 25cm to 35cm above distributor. Also, as anthracite traction Increased, the mass of elutrlatlon particles Increased, and $CO^2$ concentration decreased. As gk flow rate Increased,$O^2$ concentration decreased and $CO^2$ concentration increased. Regardless of anthracite fraction and flow rate, the uncombustible weight percentage according to average diameter of elutriation particles were approldmately high In the case of One Particles. As anthracite traction and k now rate Increased, elutriation ratio Increased. As anthracite fraction was increased, exit combustible content over feeding combustible content was Increased. Regardless of anthracite fraction, size distribution of Ued material from discharge was almost constant. Over bed temperature 85$0^{\circ}C$ and excess air 20% , the difference of combution efficiencies were little. It is estimate that the combustion condition In anthracite-bituminous coal blend combustion is suitable at the velocity 0.3m/s, bed temperature 85$0^{\circ}C$, the excess air 20%.

• Journal of Radiation Protection and Research
• /
• v.40 no.1
• /
• pp.46-54
• /
• 2015

The thermoluminescence (TL) and optically stimulated luminescence (OSL) are commonly used to measure and record the expose of individuals to ionization radiation. Design and performance test results of a newly developed TL and OSL measurement system are presented in this paper. For this purpose, the temperature of the TL material can be controlled precisely in the range of $1{\sim}1.5^{\circ}C$ by using high-frequency (35 kHz) heating system. This high-frequency power supply was made of transformer with ferrite core. For optical stimulation, we have completed an optimal combination of the filters with the arrangement of GG420 filter for filtering the stimulating light source and a UG11 filter at the detecting window (PMT). By using a high luminance blue LED (Luxeon V), sufficient luminous intensity could be obtained for optical stimulation. By using various control boards, the TL/OSL reader device was successfully interfaced with a personal computer. A software based on LabView program (National Instruments, Inc.) was also developed to control the TL/OSL reader system. In this study, a multi-functional TL/OSL dosimeter was developed and the performance testing of the system was carried out to confirm its reliability and reproducibility.

• Journal of the Korean Institute of Gas
• /
• v.21 no.6
• /
• pp.52-60
• /
• 2017

In diffusion process exhaust line during semiconductor manufacturing process, In order to improve the transportation efficiency in the piping by removing "The reaction by-product, $ZrO_2$ and The unreacted material, TEMAZ, TMA, $O_3$, etc" and "Powder being deposited", the piping temperature was raised to $80^{\circ}C$ or more by using the heater jacket, and the bellows at the rear end of the vacuum pump ruptured. So conducted a case study and try to prevent the similar accidents from occurring through case studies. The causes of the accident were analyzed as follows: the inflow of outside air due to the generation of a gap on the suction side of the vacuum pump and heating the pipe with the heater jacket resulted in the overpressure in the pipe due to the volumetric expansion of the gas generated by decomposition of the unreacted TEMAZ, It can be assumed that the most vulnerable bellows of the piping has been ruptured. In order to prevent such accidents, This study is aimed to identify the cause of pipeline rupture accident and to establish safety measures for the prevention of similar accidents by evaluating physical hazards of TEMAZ, which is assumed to be the cause of pipe rupture accident.

• Journal of the Korean Chemical Society
• /
• v.37 no.7
• /
• pp.635-641
• /
• 1993

Electrochemical cell, $Pt|air(PO_2=5.3{\times}10^{-3}atm)|Zr_{0.85}Ca_{0.15}O_{1.85}|air(PO_2= 0.21atm)|Pt$, has been designed to characterize the solid electrolyte and the temperature dependence of the electromotive force (EMF) has been measured in a temperature range of 600∼1000${\circ}$C. Solid electrolyte shows pure ionic conduction of the oxygen anion. The Fe-FexO, Co-CoO, Ni-NiO, and Cu2O-CuO electrodes have been prepared by mixing the 1 : 1 mole ratio of each metal and metal oxide and then by heating at 800${\circ}$C for 6 hours. Electrochemical cells, Pt│M(s), $MO(s)|Zr_{0.85}Ca_{0.15}O_{1.85}|air(PO_2=0.21atm)|Pt$, have been designed and the temperature dependence of the EMF has also been measured in the same temperature range. The changes of the thermodynamic state functions for the formation of the metal oxides are calculated from the electromotive forces and their temperature dependences. The material properties of the oxide systems are also discussed with the function changes.

• Nuclear Engineering and Technology
• /
• v.21 no.2
• /
• pp.89-98
• /
• 1989

The expanding copper mandrel test performed at three strain rates (3.2$\times$10E -5/s, 2.0$\times$10E-6/s and 1.2$\times$10E-7/s) over 553-873 K temperature range by varying the heating rates (8-1$0^{\circ}C$/s, 1-2$^{\circ}C$/s and 0.5$^{\circ}C$/s) in air and in vacuum (5$\times$10E-5 torr). The yield stress peak, the strain rate sensitivity minimum and the activation volume peaks could be explained in terms of the dynamic strain aging. The activation energy for dynamic strain aging obtained from the yield stress peak temperature and strain rate was 196 KJ/mol and this value was in good agreement with the activation energy for oxygen diffusion in $\alpha$-zirconium and Zircaloy-2 (207-220 KJ/mol). Therefore, oxygen atoms are responsible for the dynamic strain aging which appeared between 573 K and 673 K. The yield stress increase due to the oxidation was obtained by comparing the yield stress in air with that in vacuum and represented by the percentage increase of yield stress ( $\sigma$$^{a}$ $_{y}$ - $\sigma$$^{v}$ $_{y}$ / $\sigma$$^{v}$ $_{y}$ ). The slower the strain rate, the greater the percentage increase occurs. In order to estimate the yield stress of PWR fuel cladding material under the service environment, the yield stress in water was obtained by comparing the oxidation rate in air that in water assuming the relationship between the oxygen pick-up amount and the yield stress increase.

• Journal of the Society of Cosmetic Scientists of Korea
• /
• v.39 no.2
• /
• pp.149-158
• /
• 2013

L-ascorbic acid, the representative antioxidants, has a great effect on skin whitening, collagen synthesis, and anti-aging, but has low oxidative stability during storage. Therefore, in this study, thermal and oxidation properties of L-ascorbic acid under various storage conditions (powder, aqueous phase, changes of temperature, UV-irradiation, and inflow of external air etc.) were investigated. And the storage stability of ingredient was validated in the double-spaced pouch by analysing oxidation properties under each storage conditions (powder phase and blended with essence). In oder to analyze the thermal properties, TGA, DSC, and FT-IR analysis were carried out and UV-visible spectrophotometer & redox titration were used in parallel for oxidation property analyses. From the result of experiment, L-ascorbic acid was oxidized fast when it contained lots of metallic ion, hydroxy ion in aqueous solution under high temperature, UV-irradiation & inflow external air, whereas it was not oxidized for a long time when it was stored as pure powder although it has same condition as heating up, UV-irradiation & inflow external air. Based on this result, retention period of cosmetics which is using L-ascorbic acid, less stable material in oxidation can be innovatively increased when using double-spaced pouch that is designed and produced for separating storage of active ingredients.

• Food Science and Preservation
• /
• v.10 no.2
• /
• pp.192-199
• /
• 2003

To prepare soybean curd utilizing effectively bioactive component of soybean, ultra fine whole soybean flour(UFWSF) was used as a soybean curd material for preparation of uncompressed whole soybean flour curd(UWSFC) in this study. The UWSFC was made with treatment by proteinase and coagulant, and proximate composition, color, textural properties and sensory evaluation of that were analyzed. Protease produced from Aspergillus sojae, bromelain and papain showed soybean curd coagulation ability and the pretense produced from Aspergillus sojae showed the highest soybean curd coagulation ability. When, after first heating and homogenizing, the proteinase was added to soybean milt textural properties of UWSFC were the best. Hunter's L and b values and textural properties (hardness, fracturability springiness, gumminess and chewiness) of UWSFC using proteinase and coagulant were higher than commercial soft soybean curd and adhesiveness and cohesiveness showed contrary tendency.

• Journal of Life Science
• /
• v.21 no.1
• /
• pp.56-61
• /
• 2011

This study was performed to investigate effective extract conditions in fronds of the Ostrich fern (Matteuccia struthiopteris) to increase antioxidant compound contents and antioxidant capacity. Powder (1 g) of lyophilizated fronds were mixed with 3 kinds of solvents (MeOH, 80% EtOH and water). Extractions were carried out using not only immersion (room temp.), heating ($60^{\circ}C$) and stirring (200rpm) for 6 hr, but also through sonication in a 42 kHz ultrasonic bath for 15, 30 and 45 min. Extracts were filtrated and measured for contents of soluble solids (SS), total polyphenols (TP; tannic acid as a standard) and total flavonoids (TF; Naringin as a standard). Antioxidant activity was expressed as $RC_{50}$ for DPPH and ABTS radical scavenging. SS (0.317 $g{\cdot}g^{-1}$ db), TP (70.90 $mg{\cdot}g^{-1}$ db) and TF (41.53 $mg{\cdot}g^{-1}$ db) contents reached their highest levels when 30 minute sonication extraction with 80% EtOH was performed, and the highest DPPH and ABTS scavenging activity was observed in the same extraction conditions ($RC_{50}$=0.14 $mg{\cdot}ml^{-1}$ and 0.09 $mg{\cdot}ml^{-1}$, respectively). From the present investigation, it can be concluded that fronds of the ostrich fern can be used as a natural material for antioxidants, and sonication for 15-30 min with 80% EtOH is an ideal extraction method for increasing their antioxidant effects and saving extraction time.

• Journal of the Korean Ceramic Society
• /
• v.39 no.9
• /
• pp.822-828
• /
• 2002

Fabrication and electrical characterization of R. F. High-power unit capacitors were investigated to study on condition of fabrication processing for R. F. High-power unit capacitor and electrical characteristics according to addition of $ZrO_2$. The unit capacitors were fabricated using tape casting. The optimum mixture ratio of dielectrics and mixing binder for the slurry fabrication was 57.5∼60.0: 42.5∼40.0 wt%. The slurry viscosity was 4000∼5000 cps and casting state of green tape fabricated using these slurry was excellent. Optimum stacking was made by 200 kg/$cm^2$ pressure with 80$^{\circ}C$ heating. $ZrO_2$ was added to improve the electrical characteristics of unit capacitor, especially breakdown characteristics. The dielectric constant and loss factor of the unit condenser having different $ZrO_2$ amounts was not changed in the addition range of 1 to 5 wt%. Also, dielectric constant was not changed in the frequency range of 10 to 500 kHz. It was found that characteristics of resistance voltage was improved through the formation of $CaZrO_3$ and the reduction of particle size as about 3wt% $ZrO_2$ was added.

• Journal of Bio-Environment Control
• /
• v.21 no.4
• /
• pp.428-436
• /
• 2012

This study aimed to develop the multi-span plastic greenhouse which is suitable for tomato cultivation and is safe against climatic disasters such as typhoon or heavy snow. The width and heights of eaves and ridge of newly developed tomato greenhouse are 7, 4.5 and 6.5 m, respectively. The width is the same but the eaves and ridge heights are 1.8 and 2 m higher than conventional 1-2 W greenhouses, respectively. Cross beam has been designed as a truss structure so it can sustain loads of tomato and equipment. Tomato greenhouse has been designed according to climatic disaster preventing design standard maintaining the high height. In other words, the material dimensions and interval of materials including column and rafter have been set to stand against $40m{\cdot}s^{-1}$ of wind and 40 cm of snow. Tomato greenhouse has been equipped with rack-pinion type roof vents which have been used in glass greenhouse in order to prevent excessive rise in air temperature. This vent type is different from that of 1-2 W type greenhouse which is made by rolling up and down the vinyl at upper part of column. Roof vents are installed at ridge, and thus external air inflow and natural ventilation are maximized. As the height increases, heating cost increase as well and, therefore, tomato greenhouse has been equipped with multi-layered thermal curtain, of which thermo-keeping is excellent, to prevent heat from escaping.