• Journal of the Korean Wood Science and Technology
• /
• v.44 no.3
• /
• pp.350-359
• /
• 2016

We performed fast pyrolysis of empty fruit bunch (EFB) in the range of temperature from $400{\sim}550^{\circ}C$ and 1.3 s of residence time. The effect of temperature on the yields and physicochemical properties of pyrolytic products were also studied. Elemental and component analysis of EFB showed that the large amount of potassium (ca. 8400 ppm) presents in the feedstock. Thermogravimetric analysis suggested that the potassium in the feedstock catalyzed degradation of cellulose. The yield of bio-oil increased with increasing temperature in the range of temperature from $400{\sim}500^{\circ}C$, while that of gas and biochar decreased and showed monotonous change each with increasing temperature. When the EFB was pyrolyzed at $550^{\circ}C$, the yield of bio-oil and char decreased while that of gas increased. Water content of the bio-oils obtained at different temperatures was 20~30% and their total acid number were less than 100 mg KOH/g oil. Viscosity of the bio-oils was 11 cSt (centistoke), and heating value varied from 15 to 17 MJ/kg. Using GC/MS analysis, 27 chemical compounds which were classified into two groups (cellulose-derived and lignin-derived) were identified. Remarkably the concentration of phenol was approximately 25% based on entire chemical compounds.

• The Korea Journal of Herbology
• /
• v.21 no.2
• /
• pp.151-158
• /
• 2006

Objectives : The purpose of the present study is to observe the neuroprotective effect of the $NeuBo153^{\circledR}$ on transient focal cerebral ischemia in rats. Methods : $NeuBo153^{\circledR}$ was made by mixing the herbs, mainly the root of Panax ginseng, the root of Rehmannia glutinosa and Poria cocos, the stem bark of Acanthopanax senticosus, the root of Scutellaria baicalensis and Mel, and heating for 96 hours. Transient Focal cerebral ischemia (2 h of ischemia, 22 h of reperfusion) was induced by intraluminal suture method with SD rats. Sensory motor function was tested by rotarod test, prehensile traction test, beam balance test and foot fault test at 24 h after ischemia. The brain slices were stained by 2% 2, 3, 5-triphenyltetrazolium chloride and the infarct volume was measured by graphic analyzer at 24 h after ischemia. Results : $NeuBo153^{\circledR}$ treated group did not show significant differences compared with vehicle treated group in body temperature. Oral administration of $NeuBo153^{\circledR}$ reduced brain infarct volume by 29.7% compared with vehicle treated group. $NeuBo153^{\circledR}$ also showed protective effects on sensory motor functional deficits. Conclusion : $NeuBo153^{\circledR}$ treatment reduced brain damage and improved functional deficits induced by MCAo. It showed neuroprotective effects even when treatment was relayed 2 h after injury. Further research is required to evaluating long term functional recovery am accurate therapeutic range and mechanisms.

• Korean Journal of Materials Research
• /
• v.9 no.8
• /
• pp.804-809
• /
• 1999

Silica films were prepared on Si single crystal substrates by a sol-gel process without DMF using TEOS as a starting material. Films were fabricated by spin coating technique. For films having a composition of TEOS : HCI(1:0.05mol), gelation time, the thickness of films, the formation of cracks and the microstructure of the films were investigated as a function of the molar ratio of $CH_3OH and H_2O$. With 8mol $CH_3OH$, the longest gelation time was measured to be 640hr. The thickness of the coated films was decreased with increasing content of $CH_3OH$. The films were sintered at $500^{\circ}C$ for 1hr with a heating rate of $0.6^{\circ}C$/min. The coated films showed worm-like grains and partially cracked microstructures at an amount of $CH_3OH$ 2mol and 4mol. The addition of more than 8 mole of $CH_2OH$ resulted in crack-free silica films. This suggests that crack-free films can be fabricated by controlling the surface tension energy of the sol solutions without DMF.

• Journal of Periodontal and Implant Science
• /
• v.32 no.3
• /
• pp.577-588
• /
• 2002

Osseointegrated implants have been established as the standard treatment modality for full/partial edentulous patients since the 1960's, and the long term results for full edentulous patients have proven to be successful. Based on these results osseointegrated implants are now widely used for partial edentulous patients. There has been an increased interest towards the efficacy of wide implants, despite many reports mentioning the lower success rate of wide implants compared to regular implants. Recently, mandibular molar area defects are commonly restored using 2 wide implants, but it is not determined whether which treatment modality-3 regular implants or 2 wide implants-shows superior success rate. In this study, 2 wide implants and 3 regular implants used for the restoration of mandibular molar area are used to compare the survival rate of 1-4 years, and to analyze and compare the failure factors. The following conclusions could be drawn from this study. 1. Wide implants and regular implants showed 94.5% and 97,6% of survival rate respectively. After prosthodontic work, the survival rate was 100% and 98.1% for wide implants and regular implants respectively. 2. 5 failed implants have been removed. 2 wide implants and 1 regular implant have been removed due to failure of osseointegration. 1 wide implant was removed due to abscess formation caused by over-heating, and 1 regular implant was removed due to mechanical failure caused by over-loading within the first year of function. 3. No statistically significant difference was observed with respect to the amount of marginal bone loss of wide and regular implants.(P>0.05) In conclusion, restoration of the mandibular molar area using 3 regular implants was found to be a good treatment modality, and 2 wide implants could he considered a good treatment modality when success factors are taken into account.

• Korean Journal of Food Science and Technology
• /
• v.15 no.4
• /
• pp.414-420
• /
• 1983

Heating characteristics for retort pouches of Kimchi heated in hot water were determined as a function of various parameters for processing. Processing conditions in laboratory and commercial retort were also evaluated on the basis of storage test. D values for Lactobacillus plantarum isolated from test sample ranged from $D^{1.08}\;to\;D^{0.18}$ and z value was $10.5^{\circ}C$. Thermal diffusivity of Kimchi increased from 1.15 to $1.44{\times}10^{-3}cm/s$ by blanching for 15 min at $80^{\circ}C$. The rate of heat penetration was significantly decreased with increasing the thickness of the pouch although the decreases was less significant below 1.0cm thickness. Increasing in the ratio of solid to syrup up to 90:10 proportionately decreased $f_h$ value, but above the ratio $f_h$ values were nearly constant.

• Journal of Sensor Science and Technology
• /
• v.6 no.6
• /
• pp.500-507
• /
• 1997

For fine control of operating temperature of shape memory alloy, we investigated the effect of thermal teratment of shape memory alloy with the impurity kind. The martensitic transformation temperature in a Cu-17.25Zn-15Al and Cu-17.25Zn-15Al-1Ag/Fe was measured using electrical resistivity as a function of quenching temperature. Order-disorder phase transition temperatures in parent phase were measured and kind of transition were distinguised by DSC(differential scanning calorimeter) with heating rate variation. And structual changes were studied with XRD. For the Cu-17.25Zn-15Al shape memory alloy, the order-disorder phase transition temperature, $T_{B2}$ and $T_{L21}$ was 809K and 610K and for the Cu-17.25Zn-15Al-1Ag and Cu-17.25Zn-15Al-1Fe specimen $T_{B2}$ and $T_{L21}$ was 794K and 610K, and 803K and 613K, respectively. In all the specimens, quenching from near $T_{B2}$ leads to an increase in martensitic temperature, whereas quenching from near $T_{L21}$ leads to an decrease in martensitic temperature.

• Solar Energy
• /
• v.13 no.1
• /
• pp.1-10
• /
• 1993

The purpose of this research is to investigate the characteristics of heat transfer in the downward axisymmetric free water jet system impinged on a flat oblique plate which has the uniform heat flux. Experimental conditions considered were Reynolds number, distance between nozzle and Bat plate, inclination angle of heater surface and nozzle exit velocity. Local Nusselt number was subjected to the influence of Re number, Pr number, oblique angle of heating surface and local position of flat plate. In the wall region of downward surface, The secondary peak point of heat transfer appeared at the local point of X/D=-8 from the stagnation point. The stagnation heat transfer rate of this experimental study augments 2.4 times than that of laminar theorical solution. The stagnation nusselt number is function of Reynolds number, nozzle-plate spacing Prandtl number and oblique angle of impinging plate.

• Journal of the Microelectronics and Packaging Society
• /
• v.19 no.1
• /
• pp.47-53
• /
• 2012

Bonding strength of Sn-3.0Ag-0.5Cu solder joint due to degradation characteristic of OSP surface finish was investigated, compared with SnPb finish. The thickness variation and degradation mechanism of organic solderability preservative(OSP) coating were also analyzed with the number of reflow process. To analyze the degradation degree of solder joint strength, FR-4 PCB coated with OSP and SnPb were experienced preheat treatment as a function of reflow number from 1st to 6th pass, respectively. After 2012 chip resistors were soldered with Sn-3.0Ag-0.5Cu on the pre-heated PCB, the shear strength of solder joints was measured. The thickness of OSP increased with increase of the number of reflow pass by thermal degradation during the reflow process. It was also observed that the preservation effect of OSP decreased due to OSP degradation which led Cu pad oxidation. The mean shear strength of solder joints formed on the Cu pads finished with OSP and SnPb were 58.1 N and 62.2 N, respectively, through the pre-heating of 6 times. Although OSP was degraded with reflow process, the feasibility of its application was proven.

• Journal of Acupuncture Research
• /
• v.22 no.1
• /
• pp.109-115
• /
• 2005

Objective : The purpose of this case is to report the improvement after treatment about a patient with meralgia paresthetica. Methods : We treated the patient with acupuncture therapy and Herbal medication from 11th October 2004 to 15th October 2004 by evaluating femoral function with VAS score and R.O.M of femur joint. Results : After 5 times of treatment, this patient achieved excellent outcome following the technique, showing that clinical symptom as like heating sense, edema and pain was disappeared, VAS changed from 10 to 1 and there was no limitation of ROM of femur. Conclusions : Meralgia paresthetica is a symptom complex that includes numbness, paresthesias, and pain in the anterolateral thigh, which may result from either an entrapment neuropathy or a neuroma of the lateral femoral cutaneous nerve(LFCN). Oriental medical treatment for meralgia paresthetica resulted in satisfactory results by diminishing the symptoms progressively during the five days of treatment. Differential diagnosis was based on careful physical examination. More research of meralgia paresthetica is needed.

• KIEE International Transaction on Systems and Control
• /
• v.2D no.2
• /
• pp.78-91
• /
• 2002

In the thermal power plant, there are six manipulated variables: main steam flow, feedwater flow, fuel flow, air flow, spray flow, and gas recirculation flow. There are five controlled variables: generator output, main steam pressure, main steam temperature, exhaust gas density, and reheater steam temperature. Therefore, the thermal power plant control system is a multinput and output system. In the control system, the main steam temperature is typically regulated by the fuel flow rate and the spray flow rate, and the reheater steam temperature is regulated by the gas recirculation flow rate. However, strict control of the steam temperature must be maintained to avoid thermal stress. Maintaining the steam temperature can be difficult due to heating value variation to the fuel source, time delay changes in the main steam temperature versus changes in fuel flow rate, difficulty of control of the main steam temperature control and the reheater steam temperature control system owing to the dynamic response characteristics of changes in steam temperature and the reheater steam temperature, and the fluctuation of inner fluid water and steam flow rates during the load-following operation. Up to the present time, the Proportional-Integral-Derivative Controller has been used to operate this system. However, it is very difficult to achieve an optimal PID gain with no experience, since the gain of the PID controller has to be manually tuned by trial and error. This paper focuses on the characteristic comparison of the PID controller and the modified 2-DOF PID Controller (Two-Degrees-Freedom Proportional-Integral-Derivative) on the DCS (Distributed Control System). The method is to design an optimal controller that can be operated on the thermal generating plant in Seoul, Korea. The modified 2-DOF PID controller is designed to enable parameters to fit into the thermal plant during disturbances. To attain an optimal control method, transfer function and operating data from start-up, running, and stop procedures of the thermal plant have been acquired. Through this research, the stable range of a 2-DOF parameter for only this system could be found for the start-up procedure and this parameter could be used for the tuning problem. Also, this paper addressed whether an intelligent tuning method based on immune network algorithms can be used effectively in tuning these controllers.