• Journal of the Korean Society of Industry Convergence
• /
• v.4 no.1
• /
• pp.35-40
• /
• 2001

A spectral measurement system for reflection and transmission properties by using an optical fiber and an ellipsoidal mirror was newly developed. The hemispherical reflectance and transmittance spectra of several heating resisting ceramics materials were measured from visible to middle infrared region. The directional characteristics of reflection and transmission were also investigated in consideration of the absorptance. The measured data were analyzed by using a four flux model of radiation transfer, The radiation properties could be estimated by the obtained scattering and absorption coefficient spectra.

• Journal of the Korean Society of Industry Convergence
• /
• v.5 no.1
• /
• pp.39-43
• /
• 2002

In present much CMOS devices used in VLSI circuit and Logic circuit. With increasing a number of device in VLSI, the confidence becomes more serious. This paper describe the mechanism of breakdown on CMOS, especially n-MOS, based on Hydro Dynamic model with device self-heating. Additionally, illustrate the CMOS latch-up characteristics on simplified device structure on this paper.

• Proceedings of the Korea Concrete Institute Conference
• /
• 2001.05a
• /
• pp.225-230
• /
• 2001

Cast-in-place foamed concrete is a high porous material placed as base the layer of mortar screeds in the panel heating system, so the quality of mortar is affected by it. Therefore, this study is aims to investigate how the absorption characteristics of foamed concrete influences on mortar screeds according to the foamed ratio-62%, 67% and 72%- and the surface treatments of foamed concrete-water and acrylic emulsion primer spray, etc. The result of this study shows that water-spray in the surface of foamed concrete has a good effects to reduce mortar cracking.

• Proceedings of the KIPE Conference
• /
• 1999.07a
• /
• pp.114-117
• /
• 1999

This paper has described about principle and form of proposed circuit made use of soft switching technology ZVS(Zero-Voltage-Switching) to reduce turn on and off loss at switching. Also, the analysis of the proposed circuit was described by using normalized parameter and operating characteristics has been evaluated as to switching frequency and parameters. Based on the characteristics value, a method of the circuit design is proposed. The theoretical results are in good agreement with the experimental ones. The proposed circuit is considerated to be useful for induction heating and discharge lamp.

• Proceedings of the Korea Society for Energy Engineering kosee Conference
• /
• 1995.05a
• /
• pp.78-81
• /
• 1995

In the present study, the spray column type of direct contact heat exchangers are studied experimentally to analyze heat transfer characteristics for solar energy utilization. These experiments are carried out in the line of solar heating system, major results are as follows ; 1) the flow and aspect of working fluid drop for maxium heat transfer 2) efficiency and volumetric heat transfer coefficient of D. C. H. X. with a heavier working fluid are higher than those of D. C. H. X. with a lighter working fluid

• Proceedings of the KIEE Conference
• /
• 2002.06a
• /
• pp.72-74
• /
• 2002

In this paper, we showed the erosion characteristics of MgO protector layer releated to lifetime of plasma display panel(PDP). We observed MgO erosion characteristic as a functions of deposition conditions. In RIE condition of Xe gas, the lowest erosion rate appears in the conditions of no heating, bias voltage -30V and pressure 5mtorr. In general. as deposition rate increases, erosion rate decreases.

• Journal of the Korea Organic Resources Recycling Association
• /
• v.15 no.1
• /
• pp.134-142
• /
• 2007

In this study the physico-chemical characteristics of solid waste and the thermagravimetric analysis of waste investigated. It was found that the combustible component, water and ash were 61%, 32%, 7% respectively. The amount of combustible component was much higher than those of others. It was shown that the total carbon and hydrogen of the waste 94% and the high heating value was 2897,883(Kcal/kg). The thermagravimetric analysis showed that the weight loss of wastes occurred as temperature increased, and the rate was higher in the temperature range of $300^{\circ}C$ to $500^{\circ}C$.

• Transactions of the Korean Society of Mechanical Engineers
• /
• v.17 no.5
• /
• pp.1313-1320
• /
• 1993

Flow patterns inside the riser section and the effects of the heater inlet-and exit-restrictions, liquid charging level and the heater inlet subcooling on the flow characteristics inside an open two-phase natural circulation loop were studied experimentally. Three basic circulation modes were observed ; periodic circulation (A)(flow oscillations with incubation(no boiling) period), continuous circulations(stable operation mode with no flow oscillations), and periodic circulation (B) (flow oscillations with continuous boiling). The circulation rate increases and then decreases with the increase of the heating rate and the maximum circulation rate appears with the continuous circulation mode. The decrease of the inlet-restriction or the increase of the exitrestriction destabilizes the system. When the liquid charging level or the inlet subcooling decreases, the continuous circulation mode starts at the lower heating rate and the system is stabilized.

• Korean Journal of Air-Conditioning and Refrigeration Engineering
• /
• v.17 no.7
• /
• pp.642-648
• /
• 2005

This study has been conducted to investigate the thermopneumatic and flow characteristics of diffuser/nozzle based thermopneumatic micropumps. In this study, a transient three-dimensional numerical analysis using FSI (Fluid-Structure Interaction) model has been employed to analyze the effects of the interaction between the membrane and two fluids (air and water) in the thermopneumtic micropump. The transient temperature and pressure in the cavity, the transient displacements of the membrane and the net flow rate of the micropump have been closely calculated for the frequency of 1 Hz. It has been found that the difference of the flow rates at the inlet and outlet is larger in the cooling period than in the heating period and that the duty ratio is very important in association with pump performance because the temperature in the cavity ascends drastically in the heating period and descends slowly in the cooling period. This study can be regarded as fundamental understandings for the design and analysis of thermopneumatic micropumps.

• The Journal of Korean Medicine
• /
• v.16 no.1 s.29
• /
• pp.370-378
• /
• 1995

In order to consider the clinical efficacy of moxa combustion, understand the quality and quantity of heat stimulation and get the basic data for the development of electric moxibustion apparatus, the pattern of combustion temperature was measured by size of moxa(small, medium, large and maximum size). The results were as follows. 1. The pattern of combustion temperature by moxa burning was classified into input period, consisting of preheating and heating periods, and output period, consisting of heat retaining and cooling periods, in all experimental groups. But it was difficult to observe the preheating period in small sized moxa. 2. It was inclined that the more moxa size was large, the more the heating and heat retaining periods were long and the maximum temperature was high. The characteristics of moxa combustion is primarily by the rate of combustion temperature, gradient temperature and duration of combustion, and their correlation among these factors and their clinical effects in practice.