• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 1999.05a
• /
• pp.505-508
• /
• 1999

The effect of the heat treatment on electrochromic properties of $MoO_3$ thin films is investigated by studing optical modulation, optical density, response time, and cyclic voltammetry. From the results of XRD analysis, heat-treated at $450^{\circ}C$ in air for 1 hour $MoO_3$ thin films are found to be crystalline while as-deposited film and heat-treated at low temperature (${\leq}300^{\circ}C$) are amorphous. The electrochrornic devices using as-deposited $MoO_3$ films exhibits good electrochromic properties compare to those using the heat treated $MoO_3$ films. It has shown that the heat-treatment affected the stability and the electrochromic properties of $MoO_3$ films.

• The Journal of Korean Academy of Prosthodontics
• /
• v.27 no.2
• /
• pp.219-248
• /
• 1989

The purposes of this study were to analyze the microstructural and compositional changes of metal surfaces following different conditions of preoxidizing heat treatment, to investigate the composition of metal oxides, and to evaluate the effect of preoxidation and removal of surface oxides on microstructure and diffusion profiles. The techniques of EDAX (energy-dispersive analysis of x-ray), ESCA (electron spectroscopy for chemical analysis), and EPMA (electron probe micro analysis) were used, along with SEM (scanning electron microscopy). The obtained results were as follows : 1. A surface of the specimen became rough and the amount of the metal oxides increased with increasing the heat treatment time and temperature and the partial pressure of oxygen. 2. At an air pressure of 28' vacuum, the higher the temperature and the longer the time of preoxidation, the higher Ni concentration was detected. 3. Cr concentration in the specimen heat treated with air was higher than that of with vacuum. 4. The oxides in the specimens were mainly composed of Ni and Cr oxides. On the globular growth particles, significant rises in Al concentration of Rexillium III and Ti concentration of Verabond were noted. 5. Atomic diffusion occurred at the ceramic-metal interface, furthermore the amount of the flux was increased with preoxidation heat treatment.

• Journal of Ginseng Research
• /
• v.39 no.4
• /
• pp.304-313
• /
• 2015

Background: Ginsenoside Rg3 is a promising anticancer agent. It is usually produced by heat treatment of ginseng, in which ginsenoside Rb1 is the major ginsenoside. A kinetic study was conducted to optimize ginsenoside Rg3 production by the heat treatment of ginsenoside Rb1. Methods: Ginsenoside Rb1 was heated using an isothermal machine at $80^{\circ}C$ and $100^{\circ}C$ and analyzed using HPLC. The kinetic parameters were calculated from the experimental results. The activation energy was estimated and used to simulate the process. The optimized parameters of ginsenoside Rg3 production are suggested based on the simulation. Results: The rate constants were $0.013h^{-1}$ and $0.073h^{-1}$ for the degradation of ginsenosides Rb1 and Rg3 at $80^{\circ}C$, respectively. The corresponding rate constants at $100^{\circ}C$ were $0.045h^{-1}$ and $0.155h^{-1}$. The estimated activation energies of degradation of ginsenosides Rb1 and Rg3 were 69.2 kJ/mol and 40.9 kJ/mol, respectively. The rate constants at different temperatures were evaluated using the estimated activation energies, and the kinetic profiles of ginsenosides Rb1 and Rg3 at each temperature were simulated based on the proposed kinetic model of consecutive reaction. The optimum strategies for producing ginsenoside Rg3 from ginsenoside Rb1 are suggested based on the simulation. With increased temperature, a high concentration of ginsenoside Rg3 is formed rapidly. However, the concentration decreases quickly after the reaching the maximal concentration value. Conclusion: The optimum temperature for producing ginsenoside Rg3 should be the highest temperature technically feasible below $180^{\circ}C$, in consideration of the cooling time. The optimum reaction time for heat treatment is 30 min.

• Journal of the Korean Society for Heat Treatment
• /
• v.36 no.6
• /
• pp.402-411
• /
• 2023

In order to examine the effect of cementite precipitated on the steel surface on the carburizing rate, the carburizing process was carried out at various boost times to measure the mass gain and carbon flux, phase analysis and carbon concentration analysis were performed on the surface of the carburized specimen. In the case of the only boost type, the longer the boost time, the more the mass gain by the diffused carbon follows the parabolic law and tends to increase. In particular, as the boost time increased, the depth of cementite precipitation and the average size of cementite on the steel surface increased. At a boost time of 7 min, the fraction of cementite precipitated on the surface is 7.32 vol.%, and the carburizing rate of carbon into the surface (surface-carbon flux) is about 17.4% compared to the calculated value because the area of the chemical (catalyst) where the carburization reaction takes place is reduced. The measured carbon concentration profile of the carburized specimen tended to be generally lower than the carbon concentration calculated by the model without considering precipitated cementite. On the other hand, in the pulse type, the mass gain by the diffused carbon increased according to the boost time following a linear law. At a boost time of 7 min, the fraction of cementite precipitated on the surface was 3.62 vol.%, and the surface-carbon flux decreased by about 4.1% compared to the calculated value. As a result, a model for predicting the actual carbon flux was presented by applying the carburization resistace coefficient derived from the surface cementite fraction as a variable.

• Journal of the Korean Society of Marine Environment & Safety
• /
• v.22 no.1
• /
• pp.138-144
• /
• 2016

Titanium is resistant to general corrosion and in sea water because of the passivity layer film on the surface of material, but may be attacked by environments that cause breakdown of the protective oxide layer including hydrochloric, sulfuric and phosphoric acids. In this study, the Ti alloys were solution heat treatment 5hours at $1066^{\circ}C$ and $966^{\circ}C$, and followed by aging heat treated, 1, 4, 8 and 16 hours in $500^{\circ}C$, $600^{\circ}C$ and $650^{\circ}C$ respectively. The heat treated specimens were measured micro Vicker's hardness, and then accomplished electrochemical polarization test for comparing corrosion in 1N sulfuric acid solution. Additionally, micro structures were taken for corrosion tested specimens. The results showed that corrosion resistance was higher in solution heat treated alloy than base and age heat treated metal. Measured corrosion resistants were increased as increasing aging heat treatment time and temperature.

• Journal of Advanced Marine Engineering and Technology
• /
• v.24 no.6
• /
• pp.70-77
• /
• 2000

In this paper, the effect of solution and age heat treatment to the corrosion behavior for the Ti-6Al-4V alloy were studied by cyclic polarization methods. Ti-6Al-4V was solution heat treated at $1,066^{\circ}C$ and $966^{\circ}C$ for 5 hours, and followed by age heat treated at $650^{\circ}C$, $600^{\circ}C$ and $550^{\circ}C$ with 1, 2, 4, 8 and 16 hours under vacuum environment. Test solution was 3.5% NaCl with temperature $25^{\circ}C$. The obtained results were as follows: 1. Base metal was exhibited higher electrical charge than that of solution and aged material. With decrease of solution-treatment temperature from 1066 to $966^{\circ}C$, the electrical charge was increased due to softening of micro structure. 2. The corrosion resistance of specimen that solution treated at $966^{\circ}C$ for 5 hours and age heat treated at 650, 660 and $550^{\circ}C$ were increased with increase of aging time to 4, 8 and 16 hours respectively, and then decreased. 3. In case of 316L stainless steel, measured charge and corrosion potential was 0.0627 coulomb and -614 mV respectively. Corrosion resistance of Ti-6Al-4V was higher than that of 316L.

• Weed & Turfgrass Science
• /
• v.2 no.2
• /
• pp.170-175
• /
• 2013

Korea is carrying out weed quarantine by plant quarantine regulations including heat-treatment method to prevent the influx of exotic weeds. In order to confirm suitability for current heat-treatment criteria and find field-applicable methods which can completely devitalize quarantine weed seeds, the conditions for heat-treatment with/without 40% relative humidity were studied with 9 species among quarantine weed seeds and one weed species similar to quarantine weed. Dry heat-treatments had been tested under various temperatures and time conditions. All seeds were dead at the conditions of $95^{\circ}C$ for 48 hours, $100^{\circ}C$ for 36 hours, $110^{\circ}C$ for 24 hours, $121^{\circ}C$ for 4 hours and $130^{\circ}C$ for 30 minutes. Heat-treatments at 40% relative humidity resulted in complete seed death at the conditions of $85^{\circ}C$ for 36 hours and $90^{\circ}C$ for 16 hours. The above results show that current heat-treatment criteria are not suitable for several quarantine weeds and these conditions could be applied as a quarantine method to prevent the influx of quarantine weeds along with agricultural imports. More specific conditions for heat tolerant species such as Picris echioides and heat susceptible species such as Cuscuta spp. are necessary and will improve plant quarantine process in devitalizing quarantine weed seeds with different heat tolerances.

• The Journal of Korean Medicine
• /
• v.42 no.3
• /
• pp.153-164
• /
• 2021

Objectives: The aim of this study is to investigate the effect of Heat-sensitive Moxibustion on Benign Prostatic Hyperplasia Methods: We searched articles from Academic Journals(CAJ) online databases, Oriental Medicine Advanced Searching Integrated System (OASIS), Searching key words were '前列腺增生', '熱敏灸' and '열민구', '전립선비대'. The search range included randomized controlled trials (RCTs). Among the articles published to 2020, 10 articles were found. After review the title, abstract and original, 3 articles were selected finally to rule out treatment combined with completely different treatments. Result: The Heat-sensitive moxibustion at acupoints in the treatment of Benign prostatic hyperplasia were significantly superior to control group after treatment in the symptoms of patients, IPSS, QOL, PVR and Qmax(P<0.05). The Heat-sensitive moxibustion can significantly reduce the incidence of temporary urinary incontinence after Transurethral resection of the prostate(TURP) and improve life quality and satisfaction of patients(P<0.05). The individualized desensitization saturated time and amount of Heat-sensitive moxibustion is superior effective to general amount and time of traditional moxibustion in the total effective rate, IPSS, Ru and Qmax(P<0.01) for Benign prostatic hyperplasia. Conclusion: Heat sensitive moxibustion directly transfer heat to the source of a disease. So it can be considered as a good treatment for Benign prostate hypertrophy. It was also shown a better effect on BPH compared to traditional moxibustion, According to the thermo principles of tumor, if the tumor cell's death temperature of 43℃ is reached, that can cause tumor degeneration. Therefore I think Heat sensitive moxibustion can be applied to various tumor disease. The results of this study could be applied to clinical treatment of BPH. However, additional large-scale clinical researches should be conducted.

• Journal of the Korean Society for Heat Treatment
• /
• v.36 no.3
• /
• pp.161-173
• /
• 2023

This study investigated the effects of K_N and process time on the formation of a compound layer at a nitriding temperature of 540℃ for SCR420H material. As a result of controlled nitriding from 3 h to 20 h at K_N 1.2 atm^-1/2, compound layers were formed up to about 10 ㎛, and an effective hardening depth of about 460 ㎛ was obtained. Initially, an ε+γ' complex phase was formed, and the phase fraction changed over time, and finally, the fraction of ε phase decreased to less than 1%. With higher K_N, the compound thickness increased, a pore layer was formed on the surface, and the surface hardness decreased. By applying the controlled nitriding process, it was possible to produce annulus gears with a compound thickness of 12.8 ㎛ and an ε phase of 5% or less. The annulus gears made through controlled nitriding were mounted on a 6-speed transmission and tested for durability. As a result, the durability test of 250,000 km was satisfied, and the transmission efficiency was also confirmed to be expected.

• Korean Journal of Metals and Materials
• /
• v.50 no.6
• /
• pp.433-438
• /
• 2012

Strength change in ultra low carbon steel carburized at $880^{\circ}C$ and $930^{\circ}C$ for 10, 30, 60 and 120 minutes was investigated. The results were analyzed by a tensile test, chemical composition analysis, optical microscopy and scanning electron microscopy. Stress in the 0.5% strain specimen in the tensile test increased as the time treated at $880^{\circ}C$ and $930^{\circ}C$ increased, because the carbon diffusion layer and the martensite of the specimen increased with increasing treatment time. Martensite was found in the ferrite region in the specimen treated at $880^{\circ}C$, which is attributed to grain boundary diffusion.