• Journal of Institute of Convergence Technology
• /
• v.2 no.1
• /
• pp.38-42
• /
• 2012

A scroll compressor used in the air conditioning in automobile consists of the fixed scroll and the orbiting scroll. Temperature gradient in the scroll compressor during the operation induces the thermal expansion of two scrolls. Therefore, the gap between scrolls in the initial stage is regarded as an important variable in structural design of the scroll compressor. The coupled thermal-stress analysis was carried out for the scrolls of a scroll compressor. The temperatures of major points of two scrolls in the steady states were referred by the literature of C. Lin. The sequentially coupled thermal-stress analysis is utilized to the heat transfer analysis and the thermal expansion analysis. In the thermal expansion analysis, the contact analysis was considered between the fixed and the orbiting scrolls in order to obtain the penetration distance and the contact pressure between two scrolls. The range of deformation was from 44 to $76{\mu}m$ according to the height of the scroll. The maximum penetration distance of $60{\mu}m$ occurred at the top surface of the fixed scroll in the center of the scroll parts.

• Journal of Korean Society for Quality Management
• /
• v.47 no.3
• /
• pp.437-451
• /
• 2019

Purpose: The purpose of this study is to improve the quality of the PGM system by improving the structure and production process of slip-ring rotary joint for radar. Methods: The improvement measures for each cause are established through failure analysis of broken items. Specifically, changing in the housing to improve the heating system. Changing the transportation method to prevent damage to equipment during transport. Changing work process of the attenuator ring to prevent damage. etc. Results: The results of this study are as follows; improving the heating system reduces heat generated by the attenuator by about 7 degrees and obtain additional temperature margins. Reduction of defect rate because of adding X-band rotary joint run-out measurement test, ESS of slip-ring rotary joint and Transportation improvement(reinforced flight boxes, tube protection, etc). Getting stable VSWR values by improving work process of attenuator overheating due to a bad bonding process. Conclusion: Through this study, improvements were made to slip-ring rotary joint that failed repeatedly for various reasons. As a result of the application of the improvements, the same fault does not occur until now, so we can see that the quality of PGM has improved.

• Journal of the Korea Institute of Building Construction
• /
• v.18 no.6
• /
• pp.569-576
• /
• 2018

In modern society, a huge number of the buildings have been constructed with RC structure. RC structures have many structural instabilities due to earthquake, typhoon, construction fault, design phase errors. Therefore, many reinforcement methods are being implemented to solve this problem. In the reinforcement method, the organic epoxy adhesive used in the FRP reinforcing method is abruptly damaged when exposed to high temperature, which is directly connected to the fall of the reinforcing material. Therefore, the present study was conducted to develop inorganic refractory mortar with a certain level of adhesion ability to reduce the heat transferred to FRP reinforcement when exposed to high temperatures. As a result of the test, it showed high adhesion strength at room temperature condition with the inclusion of EVA resin, and showed no performance deterioration up to about $300^{\circ}C$ even under heating conditions. Also, it was confirmed that the backside temperature was lower as the thickness increased, and converged to a constant temperature of about $780^{\circ}C$ after 2 hours of heating.

• Journal of the Korea Institute of Information and Communication Engineering
• /
• v.23 no.3
• /
• pp.276-281
• /
• 2019

Food printers must use food ink cartridges approved by the Ministry of Food and Drug Safety (MFDS). A 2D bar code is used to read whether the ink cartridge is authentic. However, since the dye is diverged by heat pressure and printed, the barcode is contaminated. In this paper, we propose a pre-processing algorithm to solve the problem of barcode contamination by food coloring dust in a latte art printer. The algorithm is based on various morphological operations. We apply this algorithm before reading contaminated barcode images with a general QR code reader. It has been confirmed that, as compared with the existing QR code reader, the contamination rate that can be perceived is increased from 25% to 40% and even at a contamination rate of 45%, the recognition rate reaches 50%.

• Journal of the Korean Society of Propulsion Engineers
• /
• v.24 no.5
• /
• pp.34-42
• /
• 2020

In modern air combat, infrared signals play an important role in the detection of opponents and must be reduced to improve survivability and stealth. In particular, IR signals generated in the wake of aircraft engines have high intensity and short wavelengths, so most heat-tracking missiles detect these signals. Accordingly, the measurement and characteristic analysis of Gas radiation signals from the engine's wake were carried out in this study. Micro turbojet engine has been configured to simulate a real aircraft turbofan engine, and the characteristics of IR signal reduction by adjusting the bypass ratio were identified. Through this, the IR signal characteristics for each wavelength are analyzed and verification of signal reduction technologies is performed.

• Journal of the Korean Institute of Gas
• /
• v.26 no.5
• /
• pp.22-27
• /
• 2022

Atomic Layer Deposition (ALD) is a facility that deposits an atomic layer on a wafer by causing a chemical reaction after decomposition using heat or plasma by inputting two or more gases during the semiconductor process. The main gas used at this time is NH₃ (Ammonia). NH₃ has a relatively narrow explosive range with an upper limit (UFL) of 33.6% and a lower limit (LEL) of 15%, but it can explode if a large amount suddenly gathers in one place. It is Velocity and fatal if inhaled or in contact with the skin. NH₃ (Ammonia) of ALD (Atomic Layer Deposition) facility is supplied to the chamber through the gas inlet and discharged after the reaction.

• Journal of Animal Reproduction and Biotechnology
• /
• v.38 no.2
• /
• pp.84-88
• /
• 2023

Because multiple ovulation embryo transfer (MOET) in cattle includes several benefits such as wide spreading of genetically superior offspring for long distance, this biotechnological method has been widely applied to Hanwoo. When the recipients are not stayed close after embryo recovery from donor, the embryos are moved to other farms via several vehicles (car, train, and airplane). However, air travel induces lesser oxygen level, increased vibration, lower air pressure, higher noise, and increased exposure of cosmic radiation to living things than ground level. It was still unknown that fresh embryos obtained from multiple ovulation of Hanwoo could maintain their fertility after being transported via air plane, the present case report introduced a clinical case of MOET in Hanwoo after shipping fresh embryos via air transportation. The donor was multi-ovulated via follicle-stimulating hormone series of injection, which was followed by a gonadotrophin-releasing hormone injection and artificial insemination twice. The embryos were recovered by the uterine flushing, packed in ministraws, transported to recipients for 6 h including 1 h air flight, and then transferred to the synchronized recipients. During pregnancy diagnosis of early gestation period, 5 of 7 recipients (71.4%) presented no heat signs and showed fetal sacs with fluid under transrectal ultrasonography. After normal gestation period, all recipients naturally delivered healthy calves (male n = 2 and female n = 3) without abortion, stillbirth, and premature birth. The present case report indicated that transportation of fresh embryos for MOET via domestic flight in Korea did not affect to their fertility.

• Journal of the Korean Society of Safety
• /
• v.39 no.1
• /
• pp.55-61
• /
• 2024

In response to the COVID-19 pandemic, the logistics industry in Korea has rapidly been expanding, with offline demand concentrating on online platforms owing to the development of digital infrastructure. This has increased the workload of courier drivers considerably, along with labor intensity. A delivery driver died recently from overwork due to the continuous increase in delivery volume, which raises social concerns. Delivery drivers work long hours, (over 12 hours) and are greatly affected by weather conditions, such as snow, rain, heat waves, and cold waves. In addition, they lack a fixed workplace; perform atypical work handling workpieces of various sizes, weights, and shapes; and spend a large amount of time driving as part of their work. This work involves a high level of tension and requires attention and concentration. Despite the frequency of industrial accidents in the courier industry, studies on safety and health to quantitatively analyze and systematize the work of courier workers are very scarce. Therefore, to define the work process necessary for investigating the harmful factors in delivery service and the work analysis, this study conducted interviews and on-site surveys to analyze the unit work of the delivery service by targeting delivery workers. In other words, a framework of unit work for work analysis was presented to enable research and analysis by considering the aforementioned characteristics of the courier industry. The process was broadly divided into work, transport, storage, delay, and inspection. Work was divided into loading, sorting, unloading, and door subcategories, and transportation was divided into vehicle, cart, and walking subcategories as well as 10 small processes. Moreover, 22 unit works were again drawn by conducting field surveys and interviews. The risk of unit work derived from this study was ergonomically evaluated, and the ergonomic analysis revealed that uploading and transportation were the most dangerous. The results of this study could be used as basic data for preventing industrial accidents among courier workers, whose work has increased with the logistics volume and the development of the logistics industry.

• Journal of Environmental Policy
• /
• v.7 no.2
• /
• pp.1-32
• /
• 2008

This study examined the income distribution effect of the environmental taxes in the energy sector by applying the Urban Family Survey and the Household Income and Expenditure Survey to the Kakwani index. The results analyzed are as follows: first, taxes of the non-transportation energy sector show progressive tax schemes, while those of transportation energy show regressive ones. Second, we calculated the scenario-specific progressivity index on basis of the existing energy price structure. Contrary to the previous works claimed to be regressive, the progressivity in scenario I got higher than before, except for the congestion taxes. Also, the index by the total sum of taxes in scenario II showed just a little bit higher progressive tax system. In scenario III, both the value added tax and the total sum of taxes have a little regressive structure, but the indexes in the environmental taxes, heat capacity taxes, and those which the environmental tax and the congestion tax and heat capacity taxes are summed up, are in general progressive. Third, subsidizing the tax revenues raised from the environmental taxes to the poor classes by a simulation approach shows more progressive as expected, implying the more subsidy the higher the progressivity index. As a result, it is said that the implementation of the environmental taxes has no negative impact on the income distribution, and the subsidy of the tax revenue raised from it to the poor can make the income inequality improve.

• Science of Emotion and Sensibility
• /
• v.13 no.4
• /
• pp.635-646
• /
• 2010

This article focuses on Funology and a new classified application system based on concept of language and thought which are formed by body experience. It is defined by Funology Body as that. Funology Body is classifying and searching system which are consisted of a body, world (environment), and device tool. The body is sectioned by Brain, Eyes, Ears, Nose, Mouth, Hand, Torso, Feet, and Heart according as parts of the human body. This allows intuiting and experience searching as making classified system connected to the application relationship with concept of an each part of body. The Brain of the body is sub-classified by Book, Account, Business, Memory, Education, Search, and Aphorism to imply the application with thought. The Eyes take Video, Photography, and Broadcast for visibility. The Ears is categorized as Music, Instrument, Audio, and Radio for hearing. The Nose gets Perfume, Smell for olfactory sense. The Mouth is sectioned by Food, SNS, Chatting, Email, and Blog for eating and communication. The Hand sorts into Games, Kits, and Editing to handle, create, and play. The Torso is grouped by Health, Medical, Dance, Sport, Fashion, and Testyuorself related by protecting internal and meaning of the body core. The Feet is classified by Travel, Transportation, Map, and Outdoor for moving and concept of expanding the terrain. The Heart is consisted of Fear, Anger, Joy, Sadness, Acceptance, Disgust, Expectation, and Surprise for a human feeling. Beyond that, the World takes News, Time, Weather, Map, Fortune, and Shop, and Device tool gets Interface, Utilities. The Funology Body has a unique characteristic of giving intuitive and sensuous pleasure and reflection of users' attitude and taste for changing application flexibly.