• Korean Journal of Food Science and Technology
• /
• v.12 no.3
• /
• pp.170-175
• /
• 1980

A mass production of chestnut necessiates the development of economic long-term storage method. The main objective of this study was to confirm the technical aspect of the chestnut storage method which was developed by two year project and to review the method of commercial application. The chestnut used for the experiments were separated in brine $(5.5{\sim}6.0^{\circ}\:B{\acute{a}}ume)$ into matured and unmatured lots and fumigated with $CS_2$ at a 5 $lb/27\;m^3$ level for $25{\sim}30\;hrs.$ The chestnuts were packed in wooden boxes with sawdust (50% moisture) in the ratio of 1 : 1 by volume. The boxes were stored in the cold room $(1{\pm}1^{\circ}C,\;85{\sim}95%\;RH)$ and the cellar ($0{\sim}10^{\circ}C$, controlled only by circulating night cool air). The results obtained were as follows: 1. Fully matured chestnut could be successfully preserved $8{\sim}9\;months$ at a l0% decay level in the cold room and $4{\sim}5\;months$ months in cellar. 2. Immatured chestnuts wire inferior to the matured in storage stability. At the maximum storage period, its storage life was two months shorter. 3. The heat transfer equation of piled chestnuts with sawdust can be suggested as $T_{\infty}-T_0=(T_{\infty}-T_0){\cdot}10^{-t/320}$ and j and $f_h$ values were 1 and 320 min, respectively. 4. The chestnuts in the package of storage unit had longer shelf life than naked chestnut during the retail distribution at ambient temperature.

• Journal of the Korean Magnetics Society
• /
• v.9 no.4
• /
• pp.190-195
• /
• 1999

The crystallographic and magnetic properties of the system of $Fe_{1-x}Co_x$(x=0.2 and 0.4) prepared by microwave arc-melting with the maximum power of 3.5 kW and a iron-foil with thickness of 25 ${\mu}{\textrm}{m}$ have been studied by the methods of X-ray diffraction and the measurement of the magnetic hysteresis using the vibrating sample magnetometer at room temperature. The samples were prepared in three different ways: First, pellet form pressed under the pressure of 9,000 N/$\textrm{cm}^2$. Second, the sheet cold rolled. Third, thin sheet treated with the temperature of 90$0^{\circ}C$. The X-ray diffraction pattern of the sample prepared by the first method shows that the crystal structure of the sample is bcc as same as that of Fe with a good uniformity. The iron-foil has the coercivity of 43 Oe and the initial slope of magnetization of 0.328 emu/gOe. The coervicity and magnetization of the sample prepared by the second method increased as the Co content increased. But the initial slop of the magnetization decreased as the Co content increased. This means that the displacement of domain wall is suppressed by the increases of coercivity as the Co content increased. The saturation magnetization of the samples made by the third method increased. On the other hand, the coercivity of these samples decreased. The increase of saturation magnetization of the samples seems to be related to the changes in X-ray intensity after heat treatment. Also some magnetic parameters of the samples were calculated by using a simple model and compared with other values.

• The Korean Nurse
• /
• v.33 no.5
• /
• pp.63-75
• /
• 1995

The need of oriental nursing role is recently increasing. The implication of this trend is enormous not only for the need of independent of independent oriental nursing intervention. Hence, this study was designed to describe the characteristics of oriental nursing activity and identify the meaning of nursing activity in oriental hospital. A total of 24 nurses were selected by convenience sampling from eight units at one oriental hospital. A total of 168 data were collected using minute-by-minute recording during nurse s work shift. The data were analyzed using nova and scheffe method as post-hoc test The results of this study are as follows; 1. the category of nursing activity in oriental hospital 74.4% of nursing activity was the patient-oriented nursing care. The nursing activity included others (18.28%), the function-oriented nursing care (7.07%), and staff-oriented care (0.2%). 29.1 % of the patient-oriented nursing care was the direct care, and 24. 5 % of the patient-oriented nursing care was the indirect care. There was a lack of patient education and the communication patient. 2. Nursing activity in oriental hospital by characteristics 1) Nursing activity by unit For patient-oriented nursing care, there was a statistically significant difference among 8 units. In the critical care unit, the patient-oriented nursing care was mostly performed. For function-oriented nursing care, there was statistically significant difference among 8 units. In the physical therapy unit, the function-oriented nursing care was mostly performed. 2) Nursing activity in oriental hospital For all kinds of nursing activity, there was a statistically significant difference between shifts. In night shift patient-oriented nursing care, function-oriented nursing care, and other kinds of nursing care was mostly performed. Patient-oriented nursing care included indirect care, treatment set management, and the breaktime. In day shift, staff-oriented nursing care was performed. 3) Nursing activity in oriental hospital For all kinds of nursing activity, there was not a statistically significant difference by day. The day has not impact on nursing activity. 3. the meaning of activity in oriental hospital The results of this study show that the patient-oriented care was vital check, input! output check, medication, bedsore prevention, nasogastric feeding, oral care, catheterization care, perinatal care, nursing care associated with acupuncture and moxacautery, observation (fever, sweating), heat and cold application communication with patent and family, and patient room management In conclusion, two issues associated with the findings of the research appeated to be involved in the difficulty of nursing activity in hospital. The first issue was the nursing care in oriental hospital provided by nurses who have a limited understading of the principles of oriental medicine. The second issue was the deficiency of systematic guideling for oriental nursing activity. The findings suggest the need to develop the systematic guideline for oriental nursing activity. The need of continuing education for nurses who work in the oriental hospital, and the need of nursing education including oriental nursing are critical.

• Korean Journal of Materials Research
• /
• v.22 no.2
• /
• pp.61-65
• /
• 2012

A $Li_2O-2SiO_2$ ($LS_2$) glass was investigated as a lithium-ion conducting oxide glass, which is applicable to a fast ionic conductor even at low temperature due to its high mechanical strength and chemical stability. The $Li_2O-2SiO_2$ glass is likely to be broken into small pieces when quenched; thus, it is difficult to fabricate a specifically sized sample. The production of properly sized glass samples is necessary for device applications. In this study, we applied spark plasma sintering (SPS) to fabricate $LS_2$ glass samples which have a particular size as well as high transparency. The sintered samples, $15mm\phi{\times}2mmT$ in size, ($LS_2$-s) were produced by SPS between $480^{\circ}C$ and $500^{\circ}C$ at 45MPa for 3~5mim, after which the thermal and dielectric properties of the $LS_2$-s samples were compared with those of quenched glass ($LS_2$-q) samples. Thermal behavior, crystalline structure, and electrical conductivity of both samples were analyzed by differential scanning calorimetry (DSC), X-ray diffraction (XRD) and an impedance/gain-phase analyzer, respectively. The results showed that the $LS_2$-s had an amorphous structure, like the $LS_2$-q sample, and that both samples took on the lithium disilicate structure after the heat treatment at $800^{\circ}C$. We observed similar dielectric peaks in both of the samples between room temperature and $700^{\circ}C$. The DC activation energies of the $LS_2$-q and $LS_2$-s samples were $0.48{\pm}0.05eV$ and $0.66{\pm}0.04eV$, while the AC activation energies were $0.48{\pm}0.05eV$ and $0.68{\pm}0.04eV$, respectively.

• Transactions of the Korean Society of Mechanical Engineers B
• /
• v.36 no.4
• /
• pp.457-463
• /
• 2012

Current refrigerators are designed to have thin doors and walls to facilitate user convenience and increase inner storage space. However, the thin doors and walls gives rise to the problem of dew generation on the outer surface of a refrigerator due to a large critical temperature difference between the outer wall and the room air; So far, an electric heater is commonly used for making the dew to evaporate; in this case, the heater inevitably requires additional electrical power. We propose a new approach to reduce the dew generation in a refrigerator by redesigning the gasket and varying the thickness of the inner case of the refrigerator. The results of simulations performed in this study indicate that the surface temperature in the region where dew was generated was increased by approximately $0.39{\sim}3.07^{\circ}C$ without the use of a heater.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.25 no.12
• /
• pp.974-978
• /
• 2012

The effect of Cu coating on the sensing properties of nano $SnO_2:Cu$ based sensors for the $CH_4$, $CH_3CH_2CH_3$ gas was studied. This work was focussed on investigating the change of sensitivity of nano $SnO_2:Cu$ based sensors for $CH_4$, $CH_3CH_2CH_3$ gas by Cu coating. Nano sized $SnO_2$ powders were prepared by solution reduction method using stannous chloride($SnCl_2{\cdot}2H_2O$), hydrazine($N_2H_2$) and NaOH and subsequent heat treatment. XRD patterns showed that nano $SnO_2$ powders with rutile structure were grown with (110), (101), (211) dominant peak. The particle size of nano $SnO_2:Cu$ powders at 8 wt% Cu was about 50 nm. $SnO_2$ particles were found to contain many pores, according to SEM analysis. The sensitivity of nano $SnO_2:Cu$ based sensors was measured for 5 ppm $CH_4$ gas and $CH_3CH_2CH_3$ gas at room temperature by comparing the resistance in air with that in target gases. The sensitivity for both $CH_4$ and $CH_3CH_2CH_3$ gases was improved by Cu coating on the nano $SnO_2$ surface. The response time and recovery time of the $SnO_2:Cu$ gas sensors for the $CH_4$ and $CH_3CH_2CH_3$ gases were 18~20 seconds, and 13~15 seconds, respectively.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2009.11a
• /
• pp.5-5
• /
• 2009

Thin-film-transistors (TFTs) that can be prepared at low temperatures have attracted much attention because of the great potential for transparent and flexible electronics. One of the mainstreams in this field is the use of organic semiconductors such as pentacene. But device performance of the organic TFTs is still limited due to low field-effect mobility and rapid degradation after exposing to air. Alternative approach is the use of amorphous oxide semiconductors as a channel. Amorphous oxide semiconductors (AOSs) based TFTs showed the fast technological development, because AOS films can be fabricated at room temperature and exhibit the possibility in application like flexible display, electronic paper, and larges solar cells. Among the various AOSs, a-IGZO has lots of advantages because it has high channel mobility, uniform surface roughness and good transparency. [1] The high mobility is attributed to the overlap of spherical s-orbital of the heavy post-transition metal cations. This study demonstrated the effect of the variation in channel thickness from 30nm to 200nm on the TFT device performance. When the thickness was increased, turn-on voltage and subthreshold swing was decreased. The a-IGZO channels and source/drain metals were deposited with shadow mask. The a-IGZO channel layer was deposited on $SiO_2$/p-Si substrates by RF magnetron sputtering, where RF power is 150W. And working pressure is 3m Torr, at $O_2/Ar$ (2/28 sccm) atmosphere. The electrodes were formed with electron-beam evaporated Ti (30 nm) and Au (70 nm) bilayer. Finally, Al (150nm) as a gate metal was thermal-evaporated. TFT devices were heat-treated in a furnace at 250 $^{\circ}C$ and nitrogen atmosphere for 1hour. The electrical properties of the TFTs were measured using a probe-station. The TFT with channel thickness of 150nm exhibits a good subthreshold swing (SS) of 0.72 V/decade and on-off ratio of $1{\times}10^8$. The field effect mobility and threshold voltage were evaluated as 7.2 and 8 V, respectively.

• The Journal of the Korea Contents Association
• /
• v.16 no.8
• /
• pp.419-426
• /
• 2016

The research is done to analyze the change of personal dosimeter according to the elapsed times(24 hours, 1 week, 2 weeks, 3 weeks, 4 weeks) and magnetic field and find out the effective exposure treatment for radiation workers. At first, research the heat treatment and radiation of grouped TLD and keep them in different environments-exposed separately to observe the consequences of glow curve and the level of radiation exposure. As a result, we could find that 24 hours passing TLD group showed the difference in glow curve and the level of radiation. This can be considered as the change caused by magnetic exposure. Also the average radiation exposure level of TLD group, unexposed to the magnetic field, was 15.41 mSv. And the average radiation exposure level of TLD group, exposed to the magnetic field, was 14.83 mSv which decreased the biggest amount(3.80%) among the other groups. If a radiation worker, who works in PET-MRI room, uses TLD as a personal dosimeter, the level of real radiation exposure caused by exposure to the magnetic field won't change significantly as recorded at a regular record cycle but with not regular record but interim record, the lower exposure dose will be appeared than the real level of radiation.

• Journal of Dairy Science and Biotechnology
• /
• v.33 no.3
• /
• pp.203-207
• /
• 2015

The majority of food drying processes are based on the use of thermal energy. However, such methods may deteriorate the quality of the final product. Freeze-drying is one of the most useful processes for drying thermosensitive substances. Food that contains beneficial bacteria, for example, is susceptible to heat treatment, but during freeze-drying beneficial bacteria are preserved in these food items. The primary goals of this study were to develop yogurt snacks and to compare the viability of lactic acid bacteria (LAB) in yogurt snacks under different freeze-drying temperatures. In addition, the survival of LAB during storage was investigated. Survival of LAB in freeze-dried yogurt snacks gradually decreased over 16 weeks of storage. LAB had a residual viability of 25.5% after 16 weeks of storage at room temperature. LAB survived better in freeze-dried plain yogurt snacks than in freeze-dried strawberry yogurt snacks during storage. Freeze-dried yogurt snacks contained 11.9% fat, 57.1% carbohydrate, and 18.7% protein. In conclusion, the viability of LAB in freeze-dried yogurt snacks depends on the temperature during freeze-drying: the higher the freeze-drying temperature, the lower the viability of LAB in yogurt snacks. The viability of LAB in yogurt snacks was also dependent on the moisture content and nutritional value.

• Korean Journal of Food Science and Technology
• /
• v.26 no.6
• /
• pp.791-798
• /
• 1994

Ohmic heating is a food processing operation in which heat is internally generated within foods by the passage of alternating electric current. The process enables highly viscous paste foods such as Kochujang, and fermented soybean paste to be heated very fast. In order to develope the novel pasteurization process of paste foods, static Ohmic heating system was built, and heating characteristic during Ohmic heating under various conditions were studied. Electric conductivities of Kochujang and fermented soybean paste at room temperature were 1.865 S/m and 2.510 S/m, respectively and increased linearly with increasing temperature. Specific heating rate was highly dependent on the frequency. The highest heating rate was achieved at 5 KHz for Kochujang and 20 KHz for fermented soybean paste. Uniform heating throughout the sample was achieved during Ohmic heating with low frequency electrical currents, however above 5 KHz frequency, surface temperature was several degrees higher than the bulk.