• 한국자동차공학회논문집
• /
• 제10권1호
• /
• pp.17-23
• /
• 2002

In order to reduce exhaust emissions from diesel engine under wide operating range, an experimental study based on a new concept of combustion called HCDC(Homogeneous Charge Diesel Combustion) was conducted. In this concept, most of the fuel is supplied as premixed homogeneous charge and the rest is directly injected into a cylinder to ignite. In this study we compared combustion characteristics of an HCDC engine with those of conventional diesel engines. At high premixed fuel ratio and high load range, it was observed that premixed combustion heat release rate was low and diffusion combustion duration was shorten. from this experiment, it was found that NOx is reduced by the lower maximum temperature and soot is reduced by rapid combustion during diffusion combustion phase.

• 동력기계공학회지
• /
• 제21권6호
• /
• pp.110-116
• /
• 2017

Recently the global warming caused by greenhouse gas has emerged as a global environmental problem. For this reason the continued efforts to reduce greenhouse gas emission by international cooperation and each country are in progress. Climate changing has been recognized as the world economy development from fossil fuel use is the culprit. The international maritime organization marine environment protection committee of the global warming reduction emerged restrictions on air pollution have been strengthened. Therefore, the author has investigated the effects of fuel temperature on the characteristics of combustion and performance, using an four-cycle, six cylinders and direct injection diesel engine. The results of cylinder pressure, rate of pressure rise, rate of heat release and specific fuel consumption were increased by changing of fuel temperature.

• 한국자동차공학회논문집
• /
• 제16권1호
• /
• pp.152-157
• /
• 2008

The biodiesel becomes one of the favorite alternative fuel applied to diesel engines. This research aims to understand the physics of spray and combustion characteristics of a biodiesel fuel in a constant volume chamber. For spray visualization, biodiesel was injected into a combustion chamber and a high speed camera was applied at various combustion conditions. To investigate heat-release rates and flame propagations, spark was ignited on a hydrogen fuel for the premixed combustion and then biodiesel was injected directly. In addition, parametric study was made by various geometries of combustion chambers and temperatures of fuels and injection pressures. This technology may contribute to improve the performance of bio-diesel engine and reduce emissions in future.

• 한국주조공학회지
• /
• 제9권1호
• /
• pp.73-79
• /
• 1989

Microstructural characteristics of Al-3.63wt.%Pb hyper-monotectic alloy rapidly-solidified by melt spinning were examined. Possibility of forming a planar liquid -solid interface during rapid solidification of this alloy was also considered with a morphological stability theory, and a mechanism of forming banded structure observed at the bottom parts of melt-spinned specimens was considered as well. Application of the absolute stability criterion predicts the liquid-solid interface of the primary aluminium phase to be able to maintain a planar interface during the early stage of rapid solidification. Formation of banded structure was supposed to be resulted from the release of latent heat during solidification, which affect the stability of a planar liquid-solid interface.

• 수산해양기술연구
• /
• 제28권2호
• /
• pp.184-190
• /
• 1992

The combustion characteristics, ignition delay, p-t, dp/dt, Q-t of diesel oil and fish oil blended diesel oils was investigated according to pressure and temperature in a constant volume combustion bomb. The results are as follows: 1) The influence of temperature and pressure on the ignition delay was almost constant in high temperature, regardless of the blending rates, and the ignition delay was shortest in the 60% blend. 2) The maximum pressure was high in order of with pure diesel oil, with the 20% blend and the 60% blend. 3) The rate of pressure rise was high in order of with pure diesel oil, with the 20% blend and the 60% blend. The rate of maximum pressure rise was significantly higher with pure diesel oil than with two blends. 4) The amount of accumulative heat release was large in order of with pure diesel oil, with the 20% blend and the 60% blend.

• 한국기계가공학회지
• /
• 제4권1호
• /
• pp.56-62
• /
• 2005

In this study, A controlled auto-ignition (CAI) single cylinder gasoline engine is considered, focusing on the extension of operating conditions. The fuel is injected indirectly into electrically heated inlet air flow. Investigated are the engine performance characteristics under the wide range of operating conditions such as 32 to 63 in the air-fuel ratio, 1000 to 1800 rpm in the engine speed, and 150 to $180^{\circ}C$ in the inlet-air temperature. A controlled auto-ignition gasoline engine which has the super ultra lean-burn with self-ignition of gasoline fuel can be achieved by heating inlet air.

• 한국건축시공학회:학술대회논문집
• /
• 한국건축시공학회 2012년도 춘계 학술논문 발표대회
• /
• pp.295-298
• /
• 2012

Repair and strengthening is necessary to extend the service life of existing buildings. Polymer-modified cement mortar (PCM) has been extensively used as a high performance material particularly for finishing and repairing works in concrete building because of itsexcellent adhesion, waterproofing, resistance to chemical attack, and workability. As PCM contains organic polymer, it is necessary to clarify its properties at high temperature under fire, on which sufficient data are not available. This paper evaluated the burn-up characteristics of polymer-modified cement mortar with cone calorimeter test, non-combustibility test and flammability test with experimental parameters such as the types of polymer, unit-polymer content, polymer-cement ratio and thickness of the specimen.

• 한국분무공학회지
• /
• 제14권4호
• /
• pp.163-170
• /
• 2009

The present study has numerically investigates the vaporization, auto-ignition and combustion processes in the high-pressure and high-temperature conditions encountered in the diesel engine. In the present study, in order to understand the overall spray combustion characteristics of DME fuel as well as to identify the distinctive differences of DME combustion processes compared to conventional hydrocarbon liquid fuels, the sequence of the comparative analysis has been systematically made for DME and n-Heptane liquid fuels. Computations for DME fuel are made for two cases including constant fuel mass flow rate condition and fixed heat release rate. Based on numerical results, the discussions are made for the detailed combustion processes of DME and n-Heptane spray.

• 한국자동차공학회논문집
• /
• 제12권6호
• /
• pp.66-73
• /
• 2004

In this study, combustion characteristics and various performances of a Diesel fuel DI-HCCI engine using 2-stage injection method were investigated. From these researches, application ability of 2-stage injection strategy to a DI-HCCI engine was confirmed and improvement methods of performances were considered. As the results, Using 2-stage injection method, without change of engine specifications and loss of IMEP, exhaust of NOx and Smoke emissions could be reduced to about 1/3 (at 1400rpm, IMEP 6bar) compared to conventional Diesel combustion.

• 한국건축시공학회:학술대회논문집
• /
• 한국건축시공학회 2013년도 춘계 학술논문 발표대회
• /
• pp.107-108
• /
• 2013

In this study, combustibles investigation and fire growth rate experiment were performed for predicting initial fire behavior in buildings. Combustibles investigation was performed for residential buildings, which is most frequently affected by fire in Korea. Spatial characteristics and combustibles properties were separately investigated, and occupied area and layout characteristics of combustibles were identified to produce general layout models. Of the layout models, room was selected for fire test of a single compartment. From this test, fire propagation for each combustible was identified, which was delayed compared to the summed heat release rate of a single combustible.