• 한국주조공학회지
• /
• 제29권4호
• /
• pp.176-180
• /
• 2009

Effect of matrix microstructure on creep behaviors of squeeze cast magnesium matrix composites was investigated. Aluminum borate whisker was used as reinforcement and AZ31, AS52 and Sr added AS52 Mg alloys were used for matrix alloys. The reinforcement was distributed homogeneously and defect-free composite was manufactured. Creep tests were carried out at the temperature of $150^{\circ}C$ under the applied stress of 50 and 100 MPa for Mg alloys and Mg MMCs, respectively. The creep resistance of Mg MMCs was in this order: AS52-Sr > AS52 AZ31 MMCs. Void initiation during creep mainly occurred at $Mg/Mg_{17}Al_{12}$ interface and propagation went along grain boundaries. On the other hand, $Mg_2Si$ phase was not attributed to the creep void initiation.

• 동력기계공학회지
• /
• 제14권5호
• /
• pp.36-40
• /
• 2010

The ultrasonic guided wave propagates along with the given structure's wall direction. Because of this specific character, the ultrasonic guided waves arc used in many other fields. Especially, it can be readily utilized for nondestructive inspection of various structures that are made up of gas pipes, heat exchanger tubes, and thin plates. Further, the guided wave technology can be readily utilized when inspecting pipes or thin plates which pose high risk of the accident but for which the nondestructive inspection itself is impossible because it is difficult to get to them since they are coated or buried underground. In the other hand, conventional ultrasonic testing such as thickness gauging uses bulk waves and only tests the region of structure immediately below the transducer. As a result of the application about inlet and outlet cooling water line using guided wave test, we conformed that the overall corrosions were in the lower side of the 304.8 mm inlet valve and these corrosions were engaged in not locally but through the lower side of the valve line. In the near future, we can expect that the detectable defect size is smaller than before along with the development of the sensing technology.

• 한국전기전자재료학회논문지
• /
• 제29권3호
• /
• pp.135-140
• /
• 2016

In this study, we developed the solution-processed PMMA-$HfO_x$ hybrid ReRAM devices to overcome the respective drawbacks of organic and inorganic materials. The performances of PMMA-$HfO_x$ hybrid ReRAM were compared to those of PMMA- and $HfO_x$-based ReRAMs. Bipolar resistive switching behavior was observed from these ReRAMs. The PMMA-$HfO_x$ hybrid ReRAMs showed a larger operation voltage margin and memory window than PMMA-based and $HfO_x$-based ReRAMs. The reliability and electrical instability of ReRAMs were remarkably improved by blending the $HfO_x$ into PMMA. An Ohmic conduction path was commonly generated in the LRS (low resistance state). In HRS (high resistance state), the PMMA-based ReRAM showed SCLC (space charge limited conduction). the PMMA-$HfO_x$ hybrid ReRAM and $HfO_x$-based ReRAM revealed the Pool-Frenkel conduction. As a result of flexibility test, serious defects were generated in $HfO_x$ film deposited on PI (polyimide) substrate. On the other hand, the PMMA and PMMA-$HfO_x$ films showed an excellent flexibility without defect generation.

• 한국통신학회논문지
• /
• 제15권3호
• /
• pp.252-259
• /
• 1990

本 論文은 기존 LOCOS工程의 張點을 모두 겸비한 側面璧 SWAMI 技術에 대한 새로운 構造를 提示한다. 새로운 SWAMI공정은 순수 窒化膜 壓力과 體積 膨腸에 기인한 壓力을 크게 줄이기 위해서 側面璧 주위에 얇은 질화막과 反應性이온 飾刻으로 기울어진 실리콘 측면벽을 結合시켰따. 製作된 結果에 의하면, 缺陷이 없는 완전히 새부리 모양이 形成되지 않는 局地的 酸化 공정은 기울어진 面의 異方性 산화 隔離에 의해 實現시킬 수 있었다. 추가적인 마스크 段階는 要求되지 않는다. 이 工程에서 PN 다이오드의 漏泄電流는 기존 LOCOS 공정 보다 減少되었다. 한편 가장자리 部位는 漏泄電流 密度에서 평편한 接合 부위 보다 높게 分析되었다.

• 한국구조물진단유지관리공학회 논문집
• /
• 제17권4호
• /
• pp.91-100
• /
• 2013

이 연구에서는 기존아파트 외벽체의 단열 성능저하 및 보수보강에 필요한 기초 자료를 만들기 위해서 아파트의 구조체 단열성능 측정분석과 함께 단열하자에 대한 기준수립 및 평가를 하고자 한다. 또한 아파트 건축물 구조체의 열교 및 결로발생 부분을 예측하고자 하였다. 한편 시공연도별 분석에 의하여 단열기준 및 시간 경과에 따른 단열성능 정도를 분석하기 위함이다.

• 대한음성학회지:말소리
• /
• 제58호
• /
• pp.67-81
• /
• 2006

For a large corpus of time-aligned data, HMM based approaches are most widely used for automatic segmentation, providing a consistent and accurate phone labeling scheme. There are two methods for training in HMM. Flat starting method has a property that human interference is minimized but it has low accuracy. Bootstrap method has a high accuracy, but it has a defect that manual segmentation is required In this paper, a new algorithm is proposed to minimize manual work and to improve the performance of automatic segmentation. At first phase, voiced, unvoiced and silence classification is performed for each speech data frame. At second phase, the phoneme sequence is aligned dynamically to the voiced/unvoiced/silence sequence according to the acoustic phonetic rules. Finally, using these segmented speech data as a bootstrap, phoneme model parameters based on HMM are trained. For the performance test, hand labeled ETRI speech DB was used. The experiment results showed that our algorithm achieved 10% improvement of segmentation accuracy within 20 ms tolerable error range. Especially for the unvoiced consonants, it showed 30% improvement.

• 한국재료학회지
• /
• 제12권7호
• /
• pp.580-586
• /
• 2002

The effect of processing and designing variables such as pouring temperature(1400 or $1500^{\circ}C$), inoculation and risering design(T and H type) on the formation of defects such as external depression, primary and secondary shrinkage cavities in GC150 gray cast iron was investigated. In T type risering design, external depression or primary shrinkage cavity due to liquid contraction was formed in all of the eight cases. Regardless of its modulus value, the riser could not function properly in T type risering design because directional solidification was not promoted toward the riser. On the other hand, the four cases of H type risering design in which thermal sleeves were set onto the risers produced defect-free castings. In both types of the risering designs, secondary shrinkage cavity caused by solidification contraction was not observed in the casting because of the expansion pressure due to graphite precipitation and the application of rigid pep-set mold. The degree of external depression or primary shrinkage cavity was reduced with lowered pouring temperature. The effect of inoculation was diminished because of the high carbon equivalent of GC 150 gray cast iron.

• Bulletin of the Korean Chemical Society
• /
• 제21권8호
• /
• pp.769-773
• /
• 2000

The dependence of photoluminescence (PL) and photoluminescence itation (PLE) on preparation condi-tions and the aging of porous silicon carbide (PSC) have been investigatted. The fiber size of the material pre-pared under dark-current mode, labele d DCM, was larger than that of the photoassisted (PA)process.The intensity of the PL spectrum for the PA condition was higher than that of the DCM condition. The PA condition giving small fiber size exhibited amore prominent high-energy component but the emission bands of both con-ditionsobserved were rather similar. The origin of the PL may have played an importantrole in the surface defect center introduced by the reaction conditions ofHFatthe surface of the silicon carbide. Selective excita-tion of the PL bandsusingdifferent excitation wavelengths has been used to identify distinct componentswith-in the PL bandwidth. Two main PL bands with peak wavelength of494 and534 nm were clearly resolved. On the other hand, selectivc emission of the PLEbands using different emission wavelengths has been used to identify distinct components within the PLE bandwidth. The higher energy band with peak wavelength of 338 nm and the lower energy bands involving 390,451 and 500 nm were clearly resolved. According to the pro-ionged aging in air, PL spectra appearedasone band, This emission probably originated from states localized to the band-to-band recombination due to the oxidation on the crystallite surface.

• Design & Manufacturing
• /
• 제15권3호
• /
• pp.13-18
• /
• 2021

In plate forming technology, cylindrical drawing process is widely used in industry due to technological development. In this study, we used stainless steel 3042B and stainless steel 304J1, which are the most commonly used materials in the production of cold and hot water tanks for water purifiers, among cylindrical drawing products. Under the same conditions, the thickness of the sidewall of the product formed by drawn experiment was studied. As a result of the experiment, the bottom thickness of stainless steel 304J1 was considered to be thick. It is judged that the defect rate can be reduced by changing the breaking phenomenon of the floor surface of the cold and hot water bottles to the material of stainless steel 304j1. Stainless steel 304 2B material shows a sharp change in thickness from punch corner R to sidewall position, while stainless steel 304J1 material showed a uniform change from punch corner R to sidewall position. Stainless steel 304J1 material is considered to improve the clamping of the product in the process of extracting the product after hand drawing. The appearance of stainless steel 3042B products is considered to produce more wrinkles in the flange, which exerts greater tensile force on the sidewall during molding, resulting in uneven sidewall thickness.

• Journal of Ceramic Processing Research
• /
• 제20권1호
• /
• pp.59-62
• /
• 2019

Y2O3-MgO nanocomposites are promising materials for hypersonic infrared windows and domes due to their excellent midIR transmittance and mechanical properties. In this work, influence of SPS heating rate on the microstructure, IR transmittance, and mechanical properties of Y2O3-MgO nanocomposites was investigated. It was found that the average grain size decreases with a decreasing heating rate, which can be attributed to high defect concentration by rapid heating and deformation during densification. Also, the residual porosity decreases with a decreasing heating rate, which is ascribed to the enhancement of grain boundary diffusion by a large grain-boundary area (a small grain size). Consequently, high transmittance and hardness were attained by the low heating rate. On the other hand, the mechanical strength showed little difference with the heating rate change, which is somewhat different from the general knowledge on ceramics and will be discussed in this letter.