• Korean Journal of Metals and Materials
• /
• v.48 no.2
• /
• pp.148-153
• /
• 2010

The effects of Cu(II) and Al(III) on the extraction and separation of Pt(IV) and Pd(II) have been investigated in a mixed chloride solution using Alamine336 as the extractant. In the HCl concentration range of 1 to 5 M, more than 99% of Pt and Pd could be extracted by Alamine336 from all of the mixed chloride solutions investigated in this study. Lower HCl concentration led to a higher separation factor between Pd and Pt when Alamine336 concentration was constant. Extraction percentage of Cu increased with the increase of HCl concentration, while that of Al was nearly constant at 33% in our experimental range. The optimum conditions to extract Pt and Pd from Cu or Al and the separation factor under these conditions were obtained.

• Journal of Life Science
• /
• v.27 no.7
• /
• pp.754-759
• /
• 2017

The 100 l culture system was made on the basis of LED light, and Nannochloropsis oculata was cultured in f/2 medium at light intensity ($100{\mu}mol/m^2/s$), culture temperature ($20^{\circ}C{\pm}1^{\circ}C$) and LD cycle (12hr). As a result, the maximum biomass of 1.07 g/l was cultured as a result of 100 l mass culture at $100{\mu}mol/m^2/s$ and 24 mg/l nitrate concentration in LED blue (475 nm). The extraction was carried out using sonicator, homogenizer and chemical method 0.5M HCl shredding method. The contents of chlorophyll a, chlorophyll b and carotenoid were 1.6, 0.5 and 0.3 mg/g cell. When using homogenizer, it was measured at 1.0, 0.6 and 0.2 mg/g cell. The chemical breakdown method of 0.5M HCl, chlorophyll a, b, and carotenoid contents were measured as 0.9, 0.8, 0 mg/g cell. The highest amount of biomass during the distruption time was measured at 3.6 mg/g cell at 15 min disintegration and acetone, 3.6 mg/g cell of acetone, methanol, and ethanol were measured as effective solvents. Concentration was measured by using microfilter, disk type continuous centrifuge and tubular type continuous centrifuge were 16.0, 1.1 and 0.5 g/l, respectively. Four kinds of equipment such as hot air dryer, vacuum dryer, spray dryer and freeze dryer were tested to optimize the drying process. As a result, the recovery rates of spray dryer and freeze dryer were 80% and 60%.

• Bulletin of the Korean Chemical Society
• /
• v.31 no.7
• /
• pp.1945-1950
• /
• 2010

Solvent extraction experiments of Pt(IV), Pd(II) and Rh(III) by Alamine336 were performed from the mixed chloride solutions. In the HCl concentration range from 1 to 5 M, most of Pt and Pd were extracted from the mixed solutions. However, the extraction percentage of Rh was much smaller than that of Pt and Pd. Lower concentration of Alamine336 in strong HCl solution led to higher separation factor of Rh from Pt and Pd. Adding $SnCl_2$ to the mixed solutions increased the extraction percentage of Rh, while the extraction percentage of Pt and Pd was little affected. Our results showed that selective separation of Rh or coextraction of the three platinum group metals from the mixed solution would be possible by adjusting the extraction conditions.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2010.02a
• /
• pp.350-350
• /
• 2010

에너지 효율이 높은 LED조명을 사용하면 에너지 절감, 이산화탄소, 환경오염물질 배출 감소의 효과를 얻을 수 있다. 그러나 LED조명에서 발생하는 열은 LED조명의 수명과 에너지 효율을 감소시킨다. 따라서 LED조명을 상용화하기 위해서는 LED조명에서 발생되는 열을 효율적으로 제거하는 것이 필수적이며 LED조명 방열판의 생산단가 또한 낮아야 한다. 이러한 조건을 충족하는 LED조명용 방열판은 Al 6063이 주로 사용되고 있다. Al 6063은 열전도 특성이 우수하고 생산단가가 저렴하다. 그러나 100 W급 이상의 고출력 LED조명에 Al 6063을 사용하기 위해서는 Al 6063의 열 방출 특성을 향상시킬 필요가 있다. 금속의 열 방출 특성을 향상시키기 위해서 주로 이용되는 방법은 표면적을 극대화 시키는 것이다. 금속에 국부적인 깊이 부식을 일이키는 Pitting corrosion을 이용하면 저렴한 비용으로 Al 6063의 표면적을 극대화하여 방열판의 열 방출 특성을 향상시킬 수 있다. 실험에 사용한 기본적인 구조의 Al 6063 방열판의 크기는 $50{\times}50{\times}30(mm)$ 이며 1M HCl + 0.05M $H_2SO_4$에서 $I_a$ = +40 mA, $t_a$ = 60 ms, $I_c$ = -40 mA, $t_c$ =20 ms로 50, 100, 200 cycle AC 에칭 하였다. Pitting corrosion된 방열판은 $3W{\times}3$개의 LED모듈에서 1시간 발광 시킨 후, 열화상 카메라를 이용하여 표면온도를 측정하였다. 실험결과 AC에칭 cycle이 증가할수록 발열특성이 우수하였으며, Pitting corrosion을 이용하지 않은 방열판에 비해 최대 $5^{\circ}C$의 표면온도 감소가 이루어졌다. 본 연구를 통해, 저렴하면서도 열 방출 특성이 높은 방열판을 설계하면, 고출력 LED조명의 상용화를 앞당길 수 있을 것이다.

• Proceedings of the Materials Research Society of Korea Conference
• /
• 2010.05a
• /
• pp.56.1-56.1
• /
• 2010

A novel electrochemical potentiostatic method has been examined in order to enhance the hole concentration of p-type GaN thin films using KOH and HCl electrolyte. The hole concentration was increased more than 2 times by the electric voltge apply with the mobility of $10{\sim}12cm^2/V.s$. At optimum condition of 3V apply, hole concentration was enhanced more than reference sample from $1.7{\times}10^{-17}cm^{-3}$ to $4.1{\times}10^{-17}cm^{-3}$. Application of this activation method to blue-LED fabrication improved optical output from 18.4mW to 20.6mW, that is ~12% increase. SIMS analysis indicates that nearly 70% of hydrogen atoms could be removed by this method.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2014.02a
• /
• pp.313-313
• /
• 2014

GaN계 물질 기반의 광 반도체는 조명 및 디스플레이 관련 차세대 광원으로 많은 관심을 받고 있고, 효율 증대를 위한 에피, 소자 구조 및 패키지 등의 많은 연구가 진행되고 있다. 특히, 투명 전극을 이용한 광 추출 효율의 증가에 대한 연구는 전체 외부양자효율을 증가시키는 중요한 기술로 각광을 받고 있다. 이러한 투명전극은 가시광 영역의 빛을 투과하면서도 전기 전도성을 갖는 기능성 박막 전극으로 산화인듐주석이 널리 사용되고 있으나 인듐 가격의 상승과 산화인듐주석 전극 자체의 크랙 특성으로 인하여 많은 문제점이 지적되고 있다. 이러한 문제를 극복하기 위하여 GaN계 발광 다이오드에 있어서 산화인듐주석 투명 전극의 대체 물질들에 대한 많은 연구들이 활발하게 이루어 지고 있다. 특히, 투명전극 층으로 사용되는 산화인듐주석 대체 박막으로 산화아연에 대한 연구가 각광을 받고 있는 실정이다. 또한, 발광 다이오드의 효율 증가를 위해 발광소자에 표면 요철 구조 형성과 나노구조체 형성 등 박막 표면의 구조 변화를 통한 광추출효율 향상에 대한 많은 연구가 진행되고 있다. 본 연구에서는 산화아연 박막을 투명전극으로 사용하였으며 광추출효율 향상을 위해 산화아연 투명전극에 패터닝을 형성하고, 그 위에 산화아연 나노막대를 형성하여 기존에 사용하던 산화아연 투명전극보다 우수한 추출효율 및 전류 퍼짐 향상 구조를 제안하고 이에 따른 LED 소자의 광추출효율 향상을 연구하였다. 금속유기화학증착법을 이용하여 c-면 사파이어 기판에 n-GaN, 5주기의 InGaN/GaN 다중양자우물 구조 및 p-GaN의 간단한 LED구조를 성장한 후, p-GaN층 상부에 원자층 증착법을 이용하여 투명전극인 산화아연 박막을 60 nm 두께로 증착하였다. 산화아연 투명전극만 증착한 LED-A와 이후 0.1% HCl을 이용한 습식식각을 통하여 산화아연 투명전극에 육각형 모양의 패턴을 형성한 LED-B, 그리고 LED-B위에 전기화학증착법을 이용하여 $1.0{\mu}m$의 산화아연 나노 막대를 증착한 LED-C를 제작하였다. LED-A, -B 및 -C에 대한 표면 구조는 SEM이미지를 통하여 확인한 바 산화아연의 육각 패턴과 그 상부에 산화아연의 나노막대가 잘 형성된 것을 확인하였다. I-L 분석으로부터 패턴이 형성되지 않은 산화아연 투명전극으로만 구성된 LED-A에 비하여 산화아연 투명 전극에 육각 패턴을 형성한 LED-B의 전계 발광 세기가 더욱 큰 것을 확인하였다. 또한, 육각 패턴에 산화아연 나노막대를 성장시켜 융합구조를 형성한 LED-C에서는 LED-B와 -A보다 더 큰 전계 발광세기를 확인할 수 있었다. 특히, 인가 전류가 고전류로 갈수록 LED-C의 발광세기가 더욱 강해지는 것으로 효율저하현상 또한 나노융합구조의 LED-C에서 확인할 수 있었다. 이는 기존 산화아연 투명전극에 육각형의 패턴 및 나노막대융합구조를 형성할 경우 전류퍼짐현상을 극대화 할 뿐 아니라, 추가적인 광추출효율 향상 효과에 의해 질화갈륨 기반LED 소자의 광효율이 증가된 것으로 판단된다.

• Journal of the Korean Crystal Growth and Crystal Technology
• /
• v.22 no.1
• /
• pp.11-14
• /
• 2012

The AlGaN layer has direct wide bandgaps ranging from 3.4 to 6.2 eV. Nowadays, it is becoming more important to fabricate optical devices in an UV region for the many applications. The high quality AlGaN layer is necessary to establish the UV optical devices. However, the growth of AlGaN layer on GaN layer is difficult due to the lattice mismatch and difference thermal expansion coefficient between GaN layer and AlGaN layer. In this paper, we attempted to grow the LED structure on GaN template by mixed-source HVPE method with multi-sliding boat system. We tried to find the optical and lattice transition of active layer by control the Al content in mixed-source. For the growth of epi layer, the HCl and $NH_3$ gas were flowed over the mixed-source and the carrier gas was $N_2$. The temperature of source zone and growth zone was stabled at 900 and $1090^{\circ}C$, respectively. After the growth, we performed the x-ray diffraction (XRD) and electro luminescence (EL) measurement.

• Proceedings of the Korean Institute of Resources Recycling Conference
• /
• 2004.05a
• /
• pp.218-226
• /
• 2004

Solvent extraction and stripping experiments were conducted to separate iron from a spent $FeCl_3$ etching solution containing nickel. In the extraction, PC88A, MIBK and Alamine336 were tested as an extractant in various diluents. Alamine336 salt in toluene led to the highest extraction percentage of iron. Stripping percentage of iron from the loaded organic by Alamine336 increased with decreasing HCl conentration of stripping solution and with increasing volume ratio of aqueous to organic. In the operation of bench scale mixer-settler, 7 extraction stage with 1.0M Alamine336 salt in toluene and 10 stripping stage with 0.01M HCl solution resulted in a stripped solution with 133g/L of iron and in a raffinate with most of nickel together with a small amount of iron when the flow rate ratio of organic to aqueous was 7.

• Journal of the Korean Chemical Society
• /
• v.46 no.5
• /
• pp.427-436
• /
• 2002

Reaction of $trans-[FeHCl(dppe)_2]$ (1) with KSeCN led to the formation of $trans-[FeH(NCSe)(dppe)_2](2).$ Compound 2 $·CH_2Cl_2$ was structurally characterized by X-ray diffraction, in which the hydride ligand appears to be involved in the dihydrogen bonding of the type M-H${\cdot}$${\cdot}$${\cdot}$H-C.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.37 no.5
• /
• pp.486-493
• /
• 2024

Lighting has been used for a long time as a medium to convey brightness from darkness, and through incandescent lamps and fluorescent lamps, LED light sources have now become the standard in the lighting industry. Recently, the lighting equipment industry has been undergoing rapid digital transformation, starting with smart lighting, and is evolving into smart lighting customized for individuals and spaces through the development of IoT technology, cloud-based services, and data analysis. However, the blue light emitted from digital devices (computers, smartphones, tablets, etc.) or LED lights stimulates the melanopsin in the optic ganglion cells in the retina of the eye, which in turn stimulates the secretion of melatonin through the pineal gland, which regulates the secretion of melatonin. This can reduce sleep quality or disrupt biological rhythms. This interaction between blue light and melatonin has such a significant impact on human sleep patterns and overall health that it is essential to reduce exposure to blue light, especially in the evening. Human-centered lighting refers to lighting that takes into account the effects of light on the physical and mental areas, such as human activity and awakening, improvement of sleep quality, and health management. Many research institutes study the effects in the visible area and the non-visible area. By studying the impact, it is expected to improve the quality of human life. In this study, we plan to study ways to implement human-centered lighting by collecting sunrise and sunset data and linking commercialized LED packages and control devices with open-source hardware.