• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.28 no.2
• /
• pp.92-98
• /
• 2015

The magnetoelectric characteristics on layered Ni-PZT-Ni, Co, Fe composites by epoxy bonding for magnetic field sensor were investigated in the low-frequency range. The ME coefficient of Ni-PZT-Ni, Ni-PZT-Co and Ni-PZT-Fe composites reaches a maximum of $200mV/cm{\cdot}Oe$ at $H_{dc}=110$ Oe, $106mV/cm{\cdot}Oe$ at $H_{dc}=90$ Oe and $87mV/cm{\cdot}Oe$ at $H_{dc}=160$ Oe, respectively. A trend of ME charateristics on Ni-PZT-Co, Ni-PZT-Fe composites was similar to that of Ni-PZT-Ni composites. The ME output voltage shows linearly proportional to ac field $H_{ac}$ and is about 0~150 mV at $H_{ac}$=0~7 Oe and f=110 Hz in the typical Ni-PZT-Ni sample. The frequency shift effect due to the load resistance $R_L$ shows that the frequency range for magnetic field sensor application can be modulated with appropriate load resistance $R_L$. This sample will allow for a low-magnetic ac field sensor in the low-frequency (near f=110 Hz).

• Bulletin of the Korean Chemical Society
• /
• v.13 no.3
• /
• pp.306-311
• /
• 1992

The stable structures of pure ethylene and mixed ethylene-ammonia cluster ions are studied using an electron impact ionization time-of-flight mass spectrometer. Investigations on the relative cluster ion distributions of $(C_2H_4)_n(NH_3)_m^+$ under various experimental conditions suggest that $(C_2H_4)_2(NH_3)_3^+$ and $(C_2H_4)_3(NH_3)_2^+$ ions have the enhanced structural stabilities, which give insight into the feasible structure of solvated ions. For the stable configurations of these ionic species, we report an experimental evidence that both $(C_2H4)_2^+(C_2H_4)_3^+$ clusters as the central cations provide three and two hydrogen-bonding sites, respectively, for the surrounding $NH_3$ molecules. This interpretation is based on the structural stability for ethylene clusters and the intracluster ion-molecular rearrangement of the complex ion under the presence of ammonia solvent molecules.

• Bulletin of the Korean Chemical Society
• /
• v.33 no.5
• /
• pp.1547-1550
• /
• 2012

Second-order rate constants ($k_N$) have been measured spectrophotometrically for the reactions of benzyl 2-pyridyl carbonate $\mathbf{3}$ and $t$-butyl 2-pyridyl carbonate $\mathbf{3}$ with a series of alicyclic secondary amines in MeCN at $25.0{\pm}0.1^{\circ}C$. Substrate $\mathbf{4}$ is much less reactive than $\mathbf{3}$ and the steric hindrance exerted by the bulky $t$-Bu group in $\mathbf{4}$ has been attributed to its decreased reactivity. The Br${\o}$nsted-type plots for the reactions of $\mathbf{3}$ and $\mathbf{4}$ are linear with ${\beta}_{nuc}=0.57$ and 0.45, respectively. Thus, the reactions have been concluded to proceed through a concerted mechanism, although the current reactions were expected to proceed through a stepwise mechanism with a zwitterionic tetrahedral intermediate $T^{\pm}$. It has been proposed that the rate of leaving-group expulsion is accelerated by the intramolecular H-bonding interaction in $T^{\pm}$ and the "push" provided by the RO group through the resonance interaction. Thus, the enhanced nucleofugality forces the reactions to proceed through a concerted mechanism. The reactivity-selectivity principle (RSP) is not applicable to the current reaction systems, since the reaction of the less reactive $\mathbf{4}$ results in a smaller ${\beta}_{nuc}$ than that of the more reactive $\mathbf{3}$. Steric hindrance exerted by the bulky $t$-Bu group in $\mathbf{4}$ has been suggested to be responsible for the failure of the RSP.

• Proceedings of the Korean Society for Technology of Plasticity Conference
• /
• 2006.05a
• /
• pp.295-299
• /
• 2006

The inner-structure bonded(ISB) sheet metal is defined as a composite sheet metal which has middle layer of truss-structure between two skin sheets. The characteristics such as ultra-light weight, high rigidity, high strength, etc are required especially for automobile parts. The characteristic of ISB sheet metal depends on inner-structure pattern or method of bonding. Pyramid type of crimped expanded metal is used for inner-structure and both of resistance welding and adhesive bonding are applied to make a specimen. As a result of compression test, it is appeared that forming limit is 10% reduction in thickness under a load of 8kgf per unit element(one inner-structure). In case of uniaxial tensile test the non-uniform surface integrity rather than the buckling of inner-structure happened at a load of 450kgf, which indicates elongation of 7.2% and thickness reduction of 13%. The eye-inspection method was applied to examine the defects occurring on the specimen during stretch forming. In case of biaxial stretch forming only the non-uniform deformation on the surface of a skin sheet could be observed. The forming limit in stretching of ISB sheet metal with the hemi-spherical punch of 150mm in diameter was 3mm in forming depth and 5% reduction in thickness.

• Journal of the Korean Ceramic Society
• /
• v.33 no.12
• /
• pp.1414-1420
• /
• 1996

Using Si powder with average particle size of 8${\mu}{\textrm}{m}$ Si compacts were formed by pressureless powder packing method. The compacts were reaction bonded at 1350, 140$0^{\circ}C$ for 3~35 hrs under N2/H2 atmosphere and its microstructures were examined. Reaction bonded silicon nitrides showed nitridation of 90% and relative density of 88% After the impregnation of 5wt% MgO as sintering additive using aqueous solution of Mg nitrate the Si compacts were reaction bonded at 140$0^{\circ}C$ for 15hrs. The reaction bonded bodies were gas pressure sintered at 180$0^{\circ}C$ 190$0^{\circ}C$ 200$0^{\circ}C$ for 150, 300min. They showed relative density of 95% bending strength of 600MPa and fracture toughness of 6 MPa.m1/2.

• Journal of the Institute of Electronics Engineers of Korea SD
• /
• v.42 no.6 s.336
• /
• pp.17-22
• /
• 2005

Organic-inorganic hybrid type thin films are the next generation candidates as low-k materials. SiOC films are analyzed the bonding structure by the red and blue chemical shift using the fourier transform infraredspectra. Conventional chemical shift of organic chemistry is a red shift, but hybrid type SiOC films were observed the red and blue shift. The chemical shift originates from the interaction between the C-H bond and high electronegative atoms, and the blue shift in SiOC films is caused by the porosity due to the increase of the electron rich group such as much methyl radicals. The bonding structures of SiOC films are also divided into the Si-O-C cross-link structure and the Si-O-C cage-link structure due to the chemical shifts. The Si-O-C cross-link structure progressed the adhesion attributed to the C-H bond elongation in the reason of the red shift, and the dielectric constant also decreases.

• Journal of Adhesion and Interface
• /
• v.12 no.4
• /
• pp.125-132
• /
• 2011

As the enhancement of indoor air quality is increasingly compelling the use of natural materials without any emission, this study reports the preparation and performance of natural garlic adhesives for wallpaper. The natural garlic adhesives were successfully prepared by the extraction of the clove of raw garlic with water to isolate carbohydrates and proteins. Properties of the prepared garlic adhesives such as the non volatile solids content, viscosity, density, and pH were 62%, 2,789 mPa.s, $1.3g/cm^3$, and 6.6, respectively. The non-volatile solids content has a great impact on the adhesion performance of the prepared garlic adhesives, which was adequate about 60%. Bonding strength of prepared garlic adhesives was greater than the requirement of a Korean standard for wallpaper. In addition, the garlic adhesives showed antibacterial activity inheriting from the garlic. It is expected that the prepared garlic adhesives could be used as safe and natural adhesives without emitting any volatile organic compounds and formaldehyde gas.

• The Journal of Advanced Prosthodontics
• /
• v.5 no.2
• /
• pp.126-132
• /
• 2013

PURPOSE. Post surface conditioning is necessary to expose the glass fibers to enable bonding between fiber post and resin cement. The purpose of the present study was to evaluate the effect of different surface conditioning on tensile bond strength (TBS) of a glass fiber reinforced post to resin cement. MATERIALS AND METHODS. In this in vitro study, 40 extracted single canal central incisors were endodontically treated and post spaces were prepared. The teeth were divided into four groups according to the methods of post surface treatment (n=10): 1) Silanization after etching with 20% $H_2O_2$, 2) Silanization after airborne-particle abrasion, 3) Silanization, and 4) No conditioning (Control). Adhesive resin cement (Panavia F 2.0) was used for cementation of the fiber posts to the root canal dentin. Three slices of 3 mm thick were obtained from each root. A universal testing machine was used with a cross-head speed of 1 mm/minute for performing the push-out tests. Two-way ANOVA and Tukey post hoc tests were used for analyzing data (${\alpha}$=0.05). RESULTS. It is revealed that different surface treatments and root dentin regions had significant effects on TBS, but the interaction between surface treatments and root canal regions had no significant effect on TBS. There was significant difference among $H_2O_2$ + Silane Group and other three groups. CONCLUSION. There were significant differences among the mean TBS values of different surface treatments. Application of hydrogen peroxide before silanization increased the bond strength between resin cements and fiber posts. The mean TBS mean values was significantly greater in the coronal region of root canal than the middle and apical thirds.

• Restorative Dentistry and Endodontics
• /
• v.42 no.2
• /
• pp.125-133
• /
• 2017

Objectives: This study compared the effect of hexamethyldisiloxane (HMDSO) and ammonia ($NH_3$) plasmas on the bond strength of resin cement to fiber posts with conventional treatments. Materials and Methods: Sixty-five fiber posts were divided into 5 groups: Control (no surface treatment); $H_2O_2$ (24% hydrogen peroxide for 1 min); Blasting (blasting with aluminum oxide for 30 sec); $NH_3$ ($NH_3$ plasma treatment for 3 min); HMDSO (HMDSO plasma treatment for 15 min). After the treatments, the Ambar adhesive (FGM Dental Products) was applied to the post surface (n = 10). The fiber post was inserted into a silicon matrix that was filled with the conventional resin cement Allcem Core (FGM). Afterwards, the post/cement specimens were cut into discs and subjected to a push-out bond strength (POBS) test. Additionally, 3 posts in each group were evaluated using scanning electron microscopy. The POBS data were analyzed by one-way analysis of variance and the Tukey's honest significant difference post hoc test (${\alpha}=0.05$). Results: The Blasting and $NH_3$ groups showed the highest POBS values. The HMDSO group showed intermediate POBS values, whereas the Control and $H_2O_2$ groups showed the lowest POBS values. Conclusion: Blasting and $NH_3$ plasma treatments were associated with stronger bonding of the conventional resin cement Allcem to fiber posts, in a procedure in which the Ambar adhesive was used.

• Macromolecular Research
• /
• v.11 no.1
• /
• pp.9-13
• /
• 2003

Poly (vinylidene fluoride) (PVDF) samples were implanted by using high energy (MeV)F$^{2+}$ and Cl$^{2+}$ ions. We observed that AC dielectric constant of the ion-implanted PVDF samples decreased from 10.5 to 2.5 at 1 kHz as the ion dosage increased from 10$^{11}$ to 3 $\times$ 10$^{14}$ ions/$\textrm{cm}^2$. From differential scanning calorimetry experiments, we observed that PVDF samples become more disordered state through the ion implantation. The decrease of the number of bonding of C-H and C-F and the increase of unsaturated bonding were observed from X-ray photoelectron spectroscopy experiments. The emission of HF and H$_2$ molecules during the ion implantation was detected by residual gas analyzer spectrum. Based upon the results, we analyzed that the low AC dielectric constant of the MeV ion-implanted PVDF samples originated from the reduction of polarization due to the structural change of the CF$_2$ molecules in the MeV ion-implanted PVDF samples.les.