• Bulletin of the Korean Chemical Society
• /
• v.30 no.1
• /
• pp.153-156
• /
• 2009

Low temperature methane steam reforming to produce $H_2$ for fuel cells has been calculated thermodynamically considering both heat loss of the reformer and unreacted $H_2$ in fuel cell stack. According to the thermodynamic equilibrium analysis, it is possible to operate methane steam reforming at low temperatures. A scheme for the low temperature methane steam reforming to produce $H_2$ for fuel cells by burning both unconverted $CH_4$ and $H_2$ to supply the heat for steam methane reforming has been proposed. The calculated value of the heat balance temperature is strongly dependent upon the amount of unreacted $H_2$ and heat loss of the reformer. If unreacted $H_2$ increases, less methane is required because unreacted $H_2$ can be burned to supply the heat. As a consequence, it is suitable to increase the reaction temperature for getting higher $CH_4$ conversion and more $H_2$ for fuel cell stack. If heat loss increases from the reformer, it is necessary to supply more heat for the endothermic methane steam reforming reaction from burning unconverted $CH_4$, resulting in decreasing the reforming temperature. Experimentally, it has been confirmed that low temperature methane steam reforming is possible with stable activity.

• Asian-Australasian Journal of Animal Sciences
• /
• v.15 no.6
• /
• pp.851-858
• /
• 2002

This study was conducted to determine effects of whole (intact), coarsely-ground (4 mm), finely-ground (1 mm), steam-flaked and steam-flaked-ground (1 mm) corns on in vitro and in situ DM digestibilities and also in vitro fermentation characteristics. After 48 h incubation, in vitro dry matter digestibilities of whole, steam-flaked, coarsely-ground, steam-flaked-ground, and finely-ground corns were 6.79, 61.68, 76.48, 85.72 and 90.31%, respectively. Steam-flaked-ground corn showed the highest digestibility until 24 h incubation (p<0.01). After 48 h incubation, pH of whole corn decreased with a small range. However the values of pH of other media significantly decreased (p<0.01). The gas productions of finely-ground and steam-flaked-ground corns were higher than those of the other corns (p<0.01). After 24 h incubation, $NH_3$-N concentration of finely-ground and steam-flaked-ground corns increased rapidly. Total VFA was the highest in finely-ground corn, followed by steam-flaked-ground, steam-flaked, coarsely-ground and whole corns. Incorporating steam-flaked corn resulted in the highest propionate concentration (p<0.01) and the lowest acetate : propionate value (p<0.05). Finely-ground corn showed the highest in situ DM digestibility throughout the incubation period (p<0.01), followed by coarsely-ground, steam-flaked and whole corns, respectively. Overall, DM of whole corn was merely digested in vitro as well as in situ.

• Proceedings of the Korean Nuclear Society Conference
• /
• 2005.05a
• /
• pp.857-858
• /
• 2005

• International Journal of Advanced Culture Technology
• /
• v.6 no.3
• /
• pp.1-11
• /
• 2018

The purpose of this study is to develop and analyze the meaning and contents of the "H-STEAM teaching & learning model" which combines Science, Technology, Engineering, Arts & Mathematics (STEAM) with the elements of Humanities. We developed this model based on the key competencies linked with career path for middle school students in Korea, with the recognition of two issues. First, the existing Korean STEAM education lacks the elements of humanities, thus failing to achieve an authentic convergence education. Second, it is necessary to develop a program that might correspond to the Free Semester Program that was first introduced in 2013, and implemented at full scale in 2016 for middle school students in Korea. The advantages of H-STEAM are as follows: First, H-STEAM enables students to flexibly think while traversing the physical world and the symbolic world in the process of dealing with the daily problems. Second, it combines advanced technology with human sensibility and imagination, and enables students to derive creative outcomes that stimulate their minds. Third, it makes students feel and realize a point of contact between the subject that students learn, and jobs of the real world.

• Proceedings of the KSME Conference
• /
• 2003.04a
• /
• pp.2174-2179
• /
• 2003

For many years, T/G Supplier has constructed a number of thermal power plants and researched to improve the performance and the reliability of steam turbine, which are achieved by advances in design and materials technology. In recent, interest is renewed in advanced steam condition as means of improving economy of thermal power plant and reducing environmental pollution. Improvements in the maximum power have been driven by the development of advanced rotor and bucket material and longer last stage bucket. Improvements in efficiency have been brought through advances in mechanical efficiency and thermodynamic efficiency. This paper describes a number of new steam path design features introduced to the steam turbine product. And also this paper describes new design technologies' development, new technologies' trend and technologies' development for ultra-super critical steam turbine.

• Journal of computational fluids engineering
• /
• v.20 no.3
• /
• pp.1-7
• /
• 2015

When the steam is used as working fluid in fluid machinery, different from other gases as air, phase transition (steam condensation) can occur and it affects not only the flow fields, but also machine performance & efficiency. Therefore, considering phase transition phenomena in CFD calculation is required to achieve accurate prediction of steam flow and non-equilibrium wet-steam model is needed to simulate realistic steam condensing flow. In this research, non-equilibrium wet-steam model is implemented on in-house code(T-Flow), the flow fields including phase transition phenomena in convergent-divergent nozzle are studied and compared to results of advance researches.

• Resources Recycling
• /
• v.30 no.6
• /
• pp.12-18
• /
• 2021

The water-gas shift reaction is the subsequent step using steam for hydrogen enrichment and H₂/CO ratio-controlled syngas from gasification. In this study, a water-gas shift reaction was performed using syngas from an RPF gasification system. The water-gas shift using a catalyst was performed in a laboratory-scale tube reactor with a high temperature shift (HTS) and a low temperature shift (LTS). The effects of the reaction temperature, steam/carbon ratio, and flow rate on H₂ production and CO conversion were investigated. The operating temperature was 250-400℃ for the HTS system and 190-220℃ for the LTS system. Steam/carbon ratios were between 1.5 and 3.5, and the composition of reactant was CO : 40 vol%, H₂ : 25 vol%, and CO₂ : 25 vol%. The CO conversion and H₂ production increased as the reaction temperature and steam/carbon ratio increased. The CO conversion and H₂ production decreased as the flow rate increased due to reduced retention time in the catalyst bed.

• Journal of Institute of Control, Robotics and Systems
• /
• v.5 no.3
• /
• pp.363-369
• /
• 1999

In this paper, we design the robust $H_{\infty}$ controller for water level control of steam generator using a mixed $H_{\infty}$ optimization with model-matching method. Firstly we choose the desired model which has good disturbance rejection performance. Secondly we design a stabilizing controller to keep the model-matching error small and also provide sufficiently large stability margin against additive perturbations of the nominal plant. Simulation results show that proposed robust $H_{\infty}$ controller at specific power operation has satisfactory performances against the variations of load power, steam flow rate, primary circuit coolant temperature, and feedwater temperature. It can be also observed that the proposed robust $H_{\infty}$ controller exhibits better robust stability than conventional PI controller.

• Nuclear Engineering and Technology
• /
• v.35 no.4
• /
• pp.286-298
• /
• 2003

A steam explosion module, STX, has been developed using the mechanistic steam explosion analysis code, TEXAS-V, in order to estimate the dynamic load with steam explosion by implementing the module to the integrated safety analysis code, MELCOR. One of the difficulties in using mechanistic steam explosion codes is that they do not have any obvious criteria for defining some uncertain parameters such as triggering timing, triggering magnitude, mesh axial length and mesh cross-sectional area. These parameters have been user decision parts in the past. Steam explosion sample calculations and sensitivity studies on uncertain parameters were conducted to investigate those uncertain parameters. The TEXAS-V simulations were summarized in the format of a look-up table and a linear interpolation technique was adopted to calculate the steam explosion load between the data points in the table. The STX-module merged with MELCOR showed the same results as the original MELCOR and additionally it could estimate the steam explosion load in the reactor cavity.

• Journal of the Korean Society of Tobacco Science
• /
• v.17 no.2
• /
• pp.139-148
• /
• 1995

This study was carried out to investigate the effects of super heated steam on the physical and chemical changes of burley cut tobacco. Total sugar, total alkaloid, ether extracts, crude ash, total nitrogen and pH for leaf chemical constituents were analyzed. Filling power and fineness index for physical properties, and carbonyl compounds, phenol compounds, amonia, pH, hydrogen cyanide nicotine, carbon monoxide, total volatile base and tar for smoke components were also analyzed. The cut tobacco treated with super heated steam showed significant decrease in total sugar and total alkaloid. The filling power of the sample treated with the super heated steam system was increased abruptly when heated at over 250℃. The fineness index showed similar tendency to that of common toast method. Super heated steam treatment slightly decreased carbonyl compounds, phenol compounds, hydrogen cyanide, nicotine, carbon monoxide and tar in the tobacco. Especially the decrease of ammonia was the most remarkable. The pH of smoke was a little different compared with that in the common toast. The sensory test results showed that, compared to the common conveyer moving system, the tobacco treated with super heated steam system brought out more roasted flavor, lowered impact, irritation, and sting, further improved aftertaste, and lowered bitterness. The super heated steam treatment method used in the studies is expected to give better filling power, mild taste and toasted odor of tobacco than that of the common method for toast treatment. Key words : burley tobacco, super heated steam, expansion, toast.