• 대한기계학회논문집B
• /
• 제36권8호
• /
• pp.829-837
• /
• 2012

벽면 난류의 항력과 밀접한 관련이 있는 유동구조를 조사하기 위해 $Re_{\tau}$ = 180, 395, 590 의 난류채널유동에 대한 직접수치모사를 수행하였다. 확률밀도함수를 조사하여 레이놀즈 전단응력에 가장 큰 기여를 하는 Q2 이벤트를 파악하였으며 Q2 이벤트의 각도의 변화가 $y^+<50$ 에서는 벽 단위로 스케일링되며, y/h > 0.5 에서는 채널의 높이로 스케일링 됨을 확인하였다. Q2 이벤트를 조건으로 하는 조건부 평균 유동장을 조사하여 레이놀즈 전단응력의 발생과 관련이 있는 유동구조는 주 유동방향의 보텍스 및 헤어핀 형상의 보텍스임을 보였다. 또한, 순간 유동장을 관찰하여 높은 레이놀즈 전단 응력의 분포가 이러한 보텍스 구조와 관련이 있으며 1.5 ~ 3h 의 크기를 갖는 대형유동구조를 구성함을 확인하였다.

• Journal of Microbiology and Biotechnology
• /
• 제19권2호
• /
• pp.167-171
• /
• 2009

The effects of culture conditions on succinic acid production and its possible scale-up have been studied. Mannheimia succiniciproducens LPK7, engineered for enhanced production of succinic acid and reduced by-product secretion, was used for the experiments. Mannheimia succiniciproducens LPK7 is a knock-out strain of wild type deficient in the ldhA, pflB, and pta-ackA genes, and is derived from Mannheimia succiniciproducens MBEL55E. Process optimization of factors including optimal temperature, pH, carbon source, and nitrogen source was performed to enhance the production of succinic acid in flasks. To observe scale-up effects, batch fermentation was carried out at various working volumes. At a working volume of 7.0 l, the final succinic acid concentration and yield were 15.4g/l and 0.86g/g. This result shows similar amount of succinic acid obtained in lab-scale fermentation, and it is possible to scale up to larger fermentors without major problems.

• 한국소성가공학회:학술대회논문집
• /
• 한국소성가공학회 2006년도 춘계학술대회 논문집
• /
• pp.105-108
• /
• 2006

It has been issued to fabricate nano-scale patterns with large-scale in the field of digital display. Also, large-scale fabrication technology of nano pattern is very important not only for the field of digital display but also for the most of applications of the nano-scale patterns in the view of the productivity. Among the fabrication technologies, UV nano imprinting process is suitable for replicating polymeric nano-scale patterns. However, in case of conventional UV nano imprinting process using flat mold, it is not easy to replicate large areal nano patterns. Because there are several problems such as releasing, uniformity of the replica, mold fabrication and so on. In this study, to overcome the limitation of the conventional UV nano imprinting process, we proposed a continuous UV nano imprinting process using a pattern roll stamper. A pattern roll stamper that has nano-scale patterns was fabricated by attaching thin metal stamper to a roll base. A continuous UV nano imprinting system was designed and constructed. As practical examples of the process, various nano patterns with pattern size of 500, 150 and 50nm were fabricated. Finally, geometrical properties of imprinted nano patterns were measured and analyzed.

• 한국축산시설환경학회지
• /
• 제10권1호
• /
• pp.1-10
• /
• 2004

현장규모 (8.6${\times}$2.5${\times}$2.4 m) 및 파이롯트규모 (1.39${\times}$0.89${\times}$0.89 m)의 고온호기산화장치를 이용하여 공기투입량 및 처리온도에 따른 양돈분뇨의 감량화 효율을 검토하였다. 현장규모에서 공기투입장치, 거품제거장치의 설치조건이 양돈슬러리 증발량과 처리온도에 모두 영향을 미치고 있음을 알 수 있었다. 현장규모 연구는 3가지의 처리방법 (처리A:공기공급량 120㎥/h, 수중펌프 2대, 소포장치2대: 처리 B: 공기공급량 180㎥/h, 수중펌프 3대, 소포장치 3대; 처리C: 공기공급량 180㎥/h, 수중펌프 3대, 소포장치 4대)으로 실행되었다. 1일 5㎥ 양돈슬러리를 동일하게 투입하면서 얻어진 연구결과, 수위변화, 온도변화 및 증발량은 각각 처리A: 50∼100cm, 31∼$64^{\circ}C$, 55L/$\m^2$ㆍday, 처리B: 40∼90cm, 29∼$52^{\circ}C$, 75L/$\m^2$ㆍday, 처리C: 40∼70cm, 45∼$54^{\circ}C$, 120L/$\m^2$ㆍday이었다. 한편 파이롯트 규모 연구는 반 연속식으로 양돈분뇨를 투입하면서 매일 투입량을 처리1: 50L/2h, 처리2: 50L/3h, 처리3: 40L/3h, 처리4: 60L/4h으로 하여 최대 슬러리 감량조건을 도출하기 위해 수행하였다.

• 소성∙가공
• /
• 제19권3호
• /
• pp.167-172
• /
• 2010

Roll-to-roll forming process is one of important metal processing technology because the process is simple and economical. These days, with these merits, roll-to-roll forming process is tried to be employed in manufacturing the circuit board, barrier ribs and solar cell plate. However, it is difficult to apply to the forming of micro scale or sub-micro scale pattern. In this study, the roll forming processing for the micro scale is designed and analyzed. The forming of micro pattern for small electric device such as LCD panel by incremental roll forming process is analyzed. Firstly, the optimum analysis conditions are found by several analyses. And then, formability is analyzed for various protrusion shapes at various forming temperatures. The formability is evaluated in terms of filling ratio and damage value. The filling ratio is defined from the tool geometry and critical damage is determined from the analysis of uniaxial tensile test. Finally, optimum forming conditions that guarantee the successful forming are found.

• Earthquakes and Structures
• /
• 제18권6호
• /
• pp.677-689
• /
• 2020

A building structural system of moment resisting frame (MRF) with concrete filled steel tubular (CFST) columns and wide flange H beams, is one of the most conveniently constructed structural systems. However, there were few studies on evaluating seismic performance of full-scale CFST columns under high axial compression. In addition, some existing famous design codes propose various limits of width-to-thickness ratio (B/t) for steel tubes of the ductile CFST composite members. This study was intended to investigate the seismic behavior of CFST columns under high axial load compression. Four full-scale square CFST column specimens with a B/t of 42 were carried out that were subjected to horizontal cyclic-reversal loads combined with constantly light, medium and high axial loads and with a linearly varied axial load, respectively. Test results revealed that shear strength and deformation capacity of the columns significantly decreased when the axial compression exceeded 0.35 times the nominal compression strength of a CFST column, P₀. It was obvious that the higher the axial compression, the lower both the shear strength and deformation capacities were, and the earlier and faster the shear strength degradation occurred. It was found as well that higher axial compressions resulted in larger initial lateral stiffness and faster degradation of post-yield lateral stiffness. Meanwhile, the lower axial compressions led to better energy dissipation capacities with larger cumulative energy. Moreover, the study implied that under axial compressions greater than 0.35P₀, the CFST column specimens with B/t limits recommended by AISC 360 (2016), ACI 318 (2014), AIJ (2008) and EC4 (2004) codes do not provide ultimate interstory drift ratio of more than 3% radian, and only the limit in ACI 318 (2014) code satisfies this requirement when axial compression does not exceed 0.35P₀.

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 2006년도 춘계학술대회 논문집 전기기기 및 에너지변환시스템부문
• /
• pp.383-385
• /
• 2006

This paper summarizes the results of these efforts by offering a photovoltaic system structure in 50kW large scale applications installed in Chosun University dormitory roof and simulation tool. This describes configuration of utility interactive photovoltaic system which generated power supply for dormitory. In this paper represent 50kW utility PV system examination result.

• 대한기계학회논문집B
• /
• 제31권2호
• /
• pp.173-180
• /
• 2007

A series of field tests were performed to develop aerodynamic characteristic evaluation method and countermeasure technology in conventional and high-speed railway. The strength of rolling stock-induced wind which affect the people and substructure in platform and nearby track were investigated. The slipstream of passing trains was measured by hot-wire array system. The speed of trains was 110 - 125km/h for conventional ones and 300km/h for high-speed ones. The streamlined shape trains cause about 50% smaller-scale slipstream compared to the non-streamlined ones.

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 2005년도 추계학술대회 논문집 전기기기 및 에너지변환시스템부문
• /
• pp.337-339
• /
• 2005

A photovoltaic panel is a device that, through the photovoltaic effect, converts luminous energy into electric energy. Photovoltaic generation system uses infinity of sofa energy, cost of fuel is needless and there is no air pollution or waste occurrence. This paper summarizes the results of these efforts by offering a photovoltaic system structure in 50kW large scale applications installed in Chosun University dormitory roof and simulation tool. This describes configuration of utility interactive photovoltaic system which generated power supply for dormitory. In this Paper represent 50kW utility PV system examination result.

• 천문학회지
• /
• 제38권2호
• /
• pp.187-190
• /
• 2005

The Cosmic Evolution Survey (COSMOS) is a Hubble Space Telescope (HST) treasury project. The COSMOS aims to perform a 2 square degree imaging survey of an equatorial field in I(F814W) band, using the Advanced Camera for Surveys (ACS). Such a wide field survey, combined with ground-based photometric and spectroscopic data, is essential to understand the interplay between large scale structure, evolution and formation of galaxies and dark matter. In 2004, we have obtained high-quality, broad band images of the COSMOS field (B, V, r', i', and z') using Suprime-Cam on the Subaru Telescope, and we have started our new optical multi-band program, COSMOS-21 in 2005. Here, we present a brief summary of the current status of the COSMOS project together with contributions from the Subaru Telescope. Our future Subaru program, COSMOS-21, is also discussed briefly.