• Anxiety and mood
• /
• v.10 no.1
• /
• pp.59-67
• /
• 2014

Objective : To obtain the incidence rate of anxiety disorders among the active duty Korean military personnel, who visited the military hospitals from 2011 to 2013, this descriptive epidemiological study was performed. Methods : After acquiring the data for the anxiety disorders from Defense Medical Statistics Information System, the annual incidence rates were analyzed by forces, position status, and specific disease entities. Results : One thousand, nine hundred and thirteen (1,913) active duty male military personnel were diagnosed with any kinds of anxiety disorders in their first visit to the psychiatric outpatient department (OPD). The total OPD visit counts were 7,870 during the same period. Anxiety disorder, NOS was the most frequent disorder, followed by panic disorder. While the incidence rate for anxiety disorder, NOS decreased, panic disorder displayed increasing tendency. Stress-related disorders and obsessive-compulsive disorder were positioned third and fourth, respectively, for the number of first visit and they both showed decreasing tendency in annual incidence rates. Social anxiety disorder, specific phobias, generalized anxiety disorder (GAD) and mixed anxiety-depressive disorder followed next. The annual incidence rates for anxiety disorders showed decreasing tendency, particularly evident in army soldiers. However, naval officers showed higher anxiety disorder incidence rate compared to those of the army and the air forces. Conclusion : Comparing to general population, panic disorder was higher while specific phobias and GAD were lower in the Korean military. It is interesting to observe higher incidence rate for anxiety disorder in naval officers and warrants further evaluation.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2012.02a
• /
• pp.256-256
• /
• 2012

Cu가 기존 배선물질인 Al을 대체함에 따라 resistance-capacitance delay와 electromigration (EM) 등의 문제들이 어느 정도 해결되었다. 그러나 지속적인 배선 폭의 감소로 배선의 저항 증가, EM 현상 강화 그리고 stability 악화 등의 문제가 지속적으로 야기되고 있다. 이를 해결하기 위한 방법으로 Cu alloy seed layer를 이용한 barrier 자가형성 공정에 대한 연구를 진행하였다. 이 공정은 Cu 합금을 seed layer로 사용하여 도금을 한 후 열처리를 통해 $SiO_2$와의 계면에서 barrier를 자가 형성시키는 공정이다. 이 공정은 매우 균일하고 얇은 barrier를 형성할 수 있고 별도의 barrier와 glue layer를 형성하지 않아 seed layer를 위한 공간을 추가로 확보할 수 있는 장점을 가지고 있다. 또한, via bottom에 barrier가 형성되지 않아 배선 전체 저항을 급격히 낮출 수 있다. 합금 물질로는 초기 Al이나 Mg에 대한 연구가 진행되었으나, 낮은 oxide formation energy로 인해 SiO2에 과도한 손상을 주는 문제점이 제기되었다. 최근 Mn을 합금 물질로 사용한 안정적인 barrier 형성 공정이 보고 되고 있다. 하지만, barrier 형성을 하기 위해 300도 이상의 열처리 온도가 필요하고 열처리 시간 또한 긴 단점이 있다. 본 실험에서는 co-sputtering system을 사용하여 Cu-V 합금을 형성하였고, barrier를 자가 형성을 위해 300도에서 500도까지 열처리 온도를 변화시키며 1시간 동안 열처리를 실시하였다. Cu-V 공정 조건 확립을 위해 AFM, XRD, 4-point probe system을 이용하여 표면 거칠기, 결정성과 비저항을 평가하였다. Cu-V 박막 내 V의 함량은 V target의 plasma power density를 변화시켜 조절 하였으며 XPS를 통해 분석하였다. 열처리 후 시편의 단면을 TEM으로 분석하여 Cu-V 박막과 $SiO_2$ 사이에 interlayer가 형성된 것을 확인 하였으며 EDS를 이용한 element mapping을 통해 Cu-V 내 V의 거동과 interlayer의 성분을 확인하였다. PVD Cu-V 박막은 기판 온도에 큰 영향을 받았고, 200도 이상에서는 Cu의 높은 표면에너지에 의한 agglomeration 현상으로 거친 표면을 가지는 박막이 형성되었다. 7.61 at.%의 V함량을 가지는 Cu-V 박막을 300도에서 1시간 열처리 한 결과 4.5 nm의 V based oxide interlayer가 형성된 것을 확인하였다. 열처리에 의해 Cu-V 박막 내 V은 $SiO_2$와의 계면과 박막 표면으로 확산하며 oxide를 형성했으며 Cu-V 박막 내 V 함량은 줄어들었다. 300, 400, 500도에서 열처리 한 결과 동일 조성과 열처리 온도에서 Cu-Mn에 의해 형성된 interlayer의 두께 보다 두껍게 성장했다. 이는 V의 oxide formation energy가 Mn 보다 작으므로 SiO2와의 계면에서 산화막 형성이 쉽기 때문으로 판단된다. 또한, $V^{+5}$이온 반경이 $Mn^{+2}$이온 반경보다 작아 oxide 내부에서 확산이 용이하며 oxide 박막 내에 여기되는 전기장이 더 큰 산화수를 가지는 V의 경우 더 크기 때문으로 판단된다.

• Analytical Science and Technology
• /
• v.13 no.5
• /
• pp.608-615
• /
• 2000

A determination method of trace nickel and cobalt in water samples was studied and developed by adsorbing their complexes on ion exchange resin suspension. The analytical ions were formed as complexes with a ligand of APDC (ammonium pyrrolidinedithiocarbamate) and adsorbed on anion exchange resin of Dowex 2-X8. After the suspension was filtered out with membrane filter, the complexes were dissolved in HCl solution by an ultrasonic vibrator for ET-AAS determination. Several conditions were optimized as followings. pH of sample solution: 5.0, amount of ligand APDC: more than 430 times in mole ratio, the type and concentration of acid: 0.1 M HCl, and vibration time: 7 minutes. The addition of palladium in the HCl solution could improve the reproducibility and sensitivity by a matrix modification in the absorbance measurement. This procedure was applied for the analysis of three kinds of real water samples. The detection limits equivalent to 3 times standard deviation of blank were Co 0.36 ng/mL and Ni 0.27 ng/mL and recoveries in spiked samples were 99-102% for cobalt and 100-105% for nickel.

• Journal of the Korean Society of Clothing and Textiles
• /
• v.34 no.2
• /
• pp.371-384
• /
• 2010

This research investigates the historical changes of the educational system for the clothing departments at vocational high schools. According to the growth of the fashion industry, employment potential in the clothing departments of the vocational high schools, numerical changes in the educational statistics, and curriculums were investigated by papers, reports, and statistic data. The statistic data were derived from the 'Center Educational Statistics and Information', 'School Information' (Hak-gyo Alimi), 'Korean Statistical Information Services' and internet home pages of vocational high schools. Technical service workers that graduate from clothing departments and vocational high schools have limited competitiveness in a thriving fashion industry field. Highly developed fashion industries require more professional workers in fashion design, fashion marketing, and fashion materials. Compared to 1994, when 35 classes were conducted in 5 vocational high schools, 69 classes are now conducted at 15 schools. They have over 2,000 students and produce over 600 graduates. However, 222 credits of the $1^{st}$ curriculum in 1958 went down to 82 credits in the 2007 revised curriculum to complete the credits of clothing departments. The 15 courses of the 1st curriculum fell to 5 courses in the 2007 revised curriculum on the number of major subjects. It is a fundamental problem that major courses in clothing education have been excessively reduced despite the demand for of highly specialized workers in the fashion industry. In the view of operating conditions of those schools, there were several problems such as the wide gaps in the curriculum, limited equipment, the supply of teachers, and counseling on the choice of college or a career. In conclusion, the following measures are required: 1) the increase of complement credits in major subjects and renovation of curriculum, 2) national substantial support to change the social circumstance concerning vocational education and occupational consciousness, 3) operation of credit approving systems in universities and colleges for students that have completed the same courses at vocational high schools, 4) designing realistic programs for vocational education and cooperation systems with corporate enterprises.

• The Journal of Engineering Geology
• /
• v.15 no.1
• /
• pp.29-39
• /
• 2005

For detecting a ground contamination survey, soil sampling method have been used a drilling or coring technique in general. However these methods are very difficult to systematically real-time monitoring of variation of contamination degree in field. ]'n this research frequency Domain Reflectometry (FDR) system was suggested and carried out to experimental approaches for determination of oil contamination on surface and underground. Experimental method using FDR method was discussed with feasibility of measurement in the laboratory column test. It is determined to degree of oil contamination due to response of dielectric constant re-lated with volumetric water content(θ/sub w/) and volumetric oil content( θ/sub al/ ) of saturated and unsaturated soil media. And physical properties such as effective porosity and oil residual ratio of saturated soil media were also measured through real-time monitoring works using installed FDR measurement sensors, which are defected characteristics of oil movement in the saturated soil media under the soil column tests. In the results of these experiments, a range of effective porosity was estimated to about 0.35 compared with initial porosity 0.40 of manufactured saturated soil media, which is also calculated to about 87.5% to the ratio of initial porosity to effective porosity. Finally oil residual ratio which is compared with volumetric water content and volumetric oil content was calculated about 62.5%.

• The Journal of Engineering Geology
• /
• v.15 no.1
• /
• pp.67-76
• /
• 2005

This paper presents the application of a neural network for prediction of the unconfined compressive strength from physical properties and schmidt hardness number on rock samples. To investigate the suitability of this approach, the results of analysis using a neural network are compared to predictions obtained by statistical relations. The data sets containing 55 rock sample records which are composed of sandstone and shale were assembled in Daegu area. They were used to learn the neural network model with the back-propagation teaming algorithm. The rock characteristics as the teaming input of the neural network are: schmidt hardness number, specific gravity, absorption, porosity, p-wave velocity and S-wave velocity, while the corresponding unconfined compressive strength value functions as the teaming output of the neural network. A data set containing 45 test results was used to train the networks with the back-propagation teaming algorithm. Another data set of 10 test results was used to validate the generalization and prediction capabilities of the neural network.

• The Journal of Engineering Geology
• /
• v.15 no.4 s.42
• /
• pp.381-390
• /
• 2005

S City depends on the T River as source water for water supply. Arsenic and boron from the hot-spring waste-water discharged from the hot-spring spa resort and emerging from the fractures of bedrock of the river have been prevalent contaminant of the T River water. This research was conducted to propose the simple and quick surrogate parameter for water quality management easily. And through making hexa-diagram of principal ions in the water samples, existing state of the water and influence of the human activity or geological origin can be figured out. As a results of characteristics of the T River water quality using principal component analysis, the contributory percentages of the 1st, 2nd and 3rd principal components were $40.80\%,\;21.40\%\;and\;11.31\%$, respectively. Therefore it was clarified that the quality of the T River water could be explained by these three principal components. Concentration of the chloride ion, which is one of the characteristics of the hot-spring water, was well correlated to both arsenic and boron concentrations. Hence concentrations of the arsenic and boron in the raw water of the water reatment plant can be predicted by the measurement of concentration of the chloride ion.

• The Journal of Engineering Geology
• /
• v.21 no.4
• /
• pp.381-391
• /
• 2011

Weathering can reduce rock strength and eventually affect the structural stability of a rock mass, which is important in the field of engineering geology. Several methods have been developed to evaluate the degree of weathering, including the chemical weathering index. In this study, we analyzed the weathering degree and characteristics of microtextures and pores in crystalline rocks (gneiss and granites) based on petrographic observations, the chemical weathering index, mineralogy by XRD, microtextural analysis by SEM/EDS, measurements of pore size and surface area by the BET method, and microporosity by X-ray CT. The formation of secondary minerals and microtexture in gneiss and granitic rocks are assumed to be affected by complex processes such as dissolution, precipitation, and fracturing. Hence, it is clear that some chemical weathering indices that are based solely on whole-rock chemistry (e.g., CIA and CWI) are unable to provide reliable assessments of the degree of weathering. Great care is needed to evaluate the degree of chemical weathering, including an understanding of the mineralogy and microtexture of the rock mass, as well as the characteristics of micropores.

• The Journal of Engineering Geology
• /
• v.22 no.2
• /
• pp.233-241
• /
• 2012

The objectives of this study were to test geothermal conductivity (k), water velocity, water quantity, and pipe pressure from a ground heat exchanger in the field, and then to analyze these data in relation to the effectiveness and economical efficiency for application of geothermal energy. After installation of the apparatus required for field tests, geothermal conductivity values were obtained from three different cases (second, third, and fourth). The k values of the second case (506 m depth) and third case (151 m depth) are approximately 2.9 and 2.8, respectively. The k value of the fourth case (506 m depth, double pipe) is 2.5, which is similar to the second and third cases. This result indicates that hole depth is a critical factor for geothermal applications. Analysis of the field data (k, water velocity, water quantity, and pipe pressure) reveals that a single geothermal system at 506 m depth is more economically efficient than three geothermal systems at depths intervals of 151 m. Although it is more expensive to install a geothermal system at 506 m depth than at 151 m depth, test results showed that the geothermal system of the fourth case (506 m, double pipe) is more economically efficient than the system at 151 m depth. Considering the optional cost of maintenance, which is a non-operational expense, the geothermal system of the fourth case is economically efficient. Large cities and areas with high land prices should make greater use of geothermal energy.

• The Journal of Engineering Geology
• /
• v.17 no.4
• /
• pp.525-534
• /
• 2007

The peculiarity of end-expanded soil nailing method(EESNM) is in fixing the wedge-type steel body spreaded by collars and grouting its surroundings by cement milk within soils, after extending hole bottom over drilling hole diameter with top drill bit. The present study was done to establish the effect of this method. Laboratory model test were carried out to investigate the behavior characteristics with the performance of the pull-out test and failure experiment, after preparing soil test box having 1,300mm length, width 1,000mm, and height 1,100mm, and the same experimental condition was set up to compare with the general soil nailing method(GSNM). The pull-out force of about 23 percentage was increased, and the horizontal displacements 1.2 from 9.1 percentage in soil-nailed wall decreased in EESNM compare with GSNM. The axial force acting on nail increased considerably at load level over 7 ton in EESNM and 5 ton in GSNM. The predicted failure line from the maxima analyzed by axial tensile strain located at long distance from soil-nailed wall in EESNM. The EESNM demonstrated the superiority of reinforcement effect in comparison with GSNM from the results above mentioned.