• 대한금속재료학회지
• /
• 제47권9호
• /
• pp.558-566
• /
• 2009

The alloying effect of a small amount of nickel on low alloy steel for application to flue gas desulfurization(FGD) systems was studied. The structural characteristics of the rust layer were investigated by scanning electron microscopy(SEM). The electrochemical properties were examined by means of potentiostatic polarization test, potentiodynamic polarization test, and electrochemical impedance spectroscopy(EIS) in a modified green death solution of 16.9 vol.% $H_2SO_4$+0.35 vol.% HCl at $60^{\circ}C$ and an acid rain solution of $6.25{\times}10^{-5}M\;H_2SO_4+5.5{\times}10^{-3}M\;NaCl$ at room temperature. It was found that as the amount of nickel increased, the corrosion rate increased in the modified green death solution, which seemed to result from micro-galvanic corrosion between NiS and alloy matrix. In acid rain solution, the corrosion rate decreased as the amount of nickel increased due to the repulsive force of $NiFe_2O_4$ rust against $Cl^-$ ions by electronegativity.

• 대한금속재료학회지
• /
• 제47권12호
• /
• pp.866-872
• /
• 2009

The effects of magnetic powder thickness on electromagnetic wave absorption characteristics in Fe-6.5Si-0.9Cr (wt%) alloy flakes/polymer composite sheets available for quasi-microwave band have been investigated. The atomized FeSiCr powders were milled by using attritor for 12, 24, and 36 h, powder thickness changed from $40{\mu}m$ to $3{\mu}m$ upon 36 h milling. The composite sheet, including thinned magnetic flakes, exhibited higher power loss in the GHz frequency range as compared with the sheets having thick flakes. Moreover, both the complex permeability and the loss factor increased with the decrease in thickness of the alloy flakes. Therefore, the enhanced power loss property of the sheets containing thin alloy flakes was attributed to the flakes of high complex permeability, especially their imaginary part. Additionally, the complex permittivity was also increased with the reduction of flake thickness, and this behavior was considered to be helpful for improvement of the electromagnetic wave absorption characteristics in the composite sheets, including thin alloy flakes.

• 한국재료학회지
• /
• 제32권11호
• /
• pp.449-457
• /
• 2022

Halide perovskites are emerging materials for next-generation display applications, thanks to their narrow emission linewidth and band gap tunability, capable of covering the entire range of visible light. Despite their short period of research, perovskite light emitting diodes (PeLEDs) have shown rapid progress in device external quantum efficiency (EQE) in the near-infrared (NIR), red, and green emission wavelengths, and the record EQE has exceeded over 20 %. However there has been limited progress with blue emission compared to the red and green counterparts. In this review, the current status and challenges of blue PeLEDs are introduced, and strategies to produce spectrally stable blue PeLEDs are discussed. The strategies include 1) a mixed halide system in the form of 3-dimensional (3D) perovskites, 2) colloidal perovskite nanocrystals and 3) low dimensional perovskites, known as quasi-2D perovskites. In the mixed halide system, previous reports based on the compositional engineering of 3D perovskites to reduce spectral instability (i.e., halide segregation) will be discussed. Since spectral instability issue originate from the mixed halide composition in perovskites, the two other strategies are based on enlarging the band gap with a single halide composition. Finally, the prospects for each strategy are discussed, for further improvement in spectrally stable blue PeLEDs.

• 한국전기전자재료학회논문지
• /
• 제36권2호
• /
• pp.151-157
• /
• 2023

Integrating dielectric materials into LTCC is a convenient method to increase the integration density in electronic circuits. To enable co-firing of the high-k and low-k dielectric LTCC materials in a multi-material hetero-laminate, the shrinkage characteristics of both materials should be similar. Moreover, thermal expansion mismatch between materials during co-firing should be minimized. The alternating stacking of an LTCC with silica filler and that with calcium-zirconate filler was observed to examine the use of the same glass in different LTCCs to minimize the difference in shrinkage and thermal expansion coefficient. For the LTCC of silica filler with a low dielectric constant and that of calcium zirconate filler with a high dielectric constant, the amount of shrinkage was examined through a thermomechanical analysis, and the predicted appropriate fraction of each filler was applied to green sheets by tape casting. The green sheets of different fillers were alternatingly laminated to the thickness of 500 ㎛. As a result of examining the junction, it was observed through SEM that a complete bonding was achieved by constrained sintering in the structure of 'calcium zirconate 50 vol%-silica 30 vol%-calcium zirconate 50 vol%'.

• 접착 및 계면
• /
• 제20권1호
• /
• pp.9-14
• /
• 2019

이 논문에서는 항공용 전도성 페인트에 들어가는 3가지 첨가제가 공기 및 질소 조건에 노출 되었을 때의 변화를 관찰하였다. 3가지 첨가제를 바이알병에 담았고 공기조건 및 질소조건에 각 일수에 따라 보관하였다. 각 일수에 보관하면서 3가지 첨가제 질량의 변화를 파악하였다. 또한, 각기 다른 대기조건에서의 화학적 변화를 보기 위해 적외선 분광기가 사용되었다. 더 나아가 질소조건 보관 후 페인트의 성능을 확인하기 위해 도장 후 도장부착력 실험을 하였다. 시약 A와 시약 B의 경우는 질소보관 후 질량의 감소 정도가 더 작은데 반해 시약 C의 경우는 질소보관 후 질량 감소 정도가 더 큰 것을 확인하였다. 특히, 시약 B의 경우는 공기 노출 시 경화가 되는 현상을 발견하였고 적외선 분광분석 시 아이소시아네이트기 피크인 $2250cm^{-1}$의 크기가 감소함을 확인하였는데, 질소조건에서 경화정도가 늦어짐을 확인하였다. 이는, 공기 중에 있는 수분이 아이소시아네이트기의 반응을 촉진시키는데, 질소조건으로 치환하면서 반응을 지연시켰다.

• Korean Chemical Engineering Research
• /
• 제59권4호
• /
• pp.521-531
• /
• 2021

진공가압함침공정(Vacuum Pressure Impregnation, VPI)은 발전기, 전동기 등 대형 회전기에 사용되는 고정자 권선에 에폭시 계열의 레진을 코팅시켜 물성을 강화하는 공정이다. VPI 공정 중 진공과 가압과정에서 에폭시 레진의 기화에 의해 레진 가스가 발생하고, 함침공정이 끝나고 경화를 위해 탱크 개방 시 레진 가스가 제거되지 않고 탱크 밖으로 유출된다. 유출된 레진 가스가 작업장 전체에 확산 시 화재, 폭발 및 호흡기 문제와 같은 안전 환경 문제가 있으므로 공정 내 레진 가스 배출시스템이 필요하다. 따라서, 본 연구에서는 VPI 공정에서 발생한 레진 가스를 배출하는 시스템을 설계하기 위해 전산유체역학(Computational Fluid Dynamics, CFD)을 이용하여 공기 유입구·배출구의 위치에 따른 배출효율에 대한 사례연구를 진행하였다. 본 연구의 최적의 배출시스템을 활용 시 1,800초 이내 90%이상의 레진 가스를 배출할 수 있으며, 레진 가스의 폭발하한계(Low Explosive Limit, LEL)이하로 레진 가스의 분율을 낮출 수 있었다.

• 한국전기전자재료학회논문지
• /
• 제35권5호
• /
• pp.499-503
• /
• 2022

La_0.7Sr_0.3MnO₃ precursor solution were prepared by a sol-gel method. La_0.7Sr_0.3MnO₃ thin films were fabricated by a spin-coating method on a Pt/Ti/SiO₂/Si substrate. Structural and electrical properties with the variation of sintering temperature were measured. All specimens exhibited a polycrystalline orthorhombic crystal structure, and the average thickness of the specimens coated 6 times decreased from about 427 nm to 383 nm as the sintering temperature increased from 740℃ to 830℃. Electrical resistance decreased as the sintering temperature increased. In the La_0.7Sr_0.3MnO₃ thin films sintered at 830℃, electrical resistivity, TCR, B-value, and activation energy were 0.0374 mΩ·cm, 0.316%/℃, 296 K and 0.023 eV, respectively.

• 한국전기전자재료학회논문지
• /
• 제37권3호
• /
• pp.297-303
• /
• 2024

In this study, KTN heterolayer thin films were fabricated by alternately stacking films of K(Ta_0.70Nb_0.30)O₃ and K(Ta_0.55Nb_0.45)O₃ synthesized using the sol-gel method. The sintering temperature and time were 750℃ and 1 hour, respectively. All specimens exhibited a polycrystalline pseudo-cubic crystal structure, with a lattice constant of approximately 0.398 nm. The average grain size was around 130~150 nm, indicating relatively uniform sizes regardless of the number of coatings. The average thickness of a single-coated film was approximately 70 nm. The phase transition temperature of the KTN heterolayer films was found to be approximately 8~12℃. Moreover, the 6-coated KTN heterolayer film displayed an excellent dielectric constant of about 11,000. As the number of coatings increased, and consequently the film thickness, the remanent polarization increased, while the coercive field decreased. The 6-coated KTN heterolayer film exhibited a remanent polarization and coercive field of 11.4 μC/cm² and 69.3 kV/cm at room temperature, respectively. ΔT showed the highest value at a temperature slightly above the Curie temperature, and for the 6-coated KTN heterolayer film, the ΔT and ΔT/ΔE were approximately 1.93 K and 0.128×10^-6 K·m/V around 40℃, respectively.

• 한국정보디스플레이학회:학술대회논문집
• /
• 한국정보디스플레이학회 2006년도 6th International Meeting on Information Display
• /
• pp.942-945
• /
• 2006

The picture quality of a plasma display panel is very sensitive to the phosphor characteristics such as luminescence, decay time, surface properties, and even longevity of phosphor material in itself. In our previous work, the discharging characteristics in green cell of PDP were demonstrated to be enhanced by coating $Zn_2SiO_4:Mn^{2+}$ phosphors with positively charged metal oxide such as MgO. Here, $Zn_2SiO_4:Mn^{2+}$ phosphors were coated by various metal oxides for examining the coating effect on the picture quality. Specially, longevity while fabricating the panel was investigated for panel application in this work. Also the effects of ion and electron bombardment on the phosphor surface will be discussed in this work.

• 한국정보디스플레이학회:학술대회논문집
• /
• 한국정보디스플레이학회 2005년도 International Meeting on Information Displayvol.II
• /
• pp.1523-1525
• /
• 2005

$CaZrO_3:Tb$ as a new green-emitting phosphor, has been synthesized by solid state reaction. Photoluminescence and cathodoluminescence properties for the phosphor with a Perovskite structure were investigated. The $CaZrO_3:Tb$ phosphor, which has several emission peaks due to energy transfer from $^5D_4$ to $^7F_J(J=6,5,4,3)$ of $Tb^{3+}$ ion, exhibited strong green luminescence with the main emission peak centered at 545 nm. Optimum Tb concentration was 0.02mol%.