• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.28 no.7A
• /
• pp.433-439
• /
• 2003

In this paper, we proposed a novel true time-delay (TTD) feeder for phased array antennas (PAAs) using fiber Bragg gratings (FBGs) and fibers coated with Cr/Au film. This structure requires less number of FBGs than the previously proposed FBG TTD feeders since one FBG is replaced with a metal film reflector in a strand of optical delay line connected to each antenna element and also provides the flexible wavelength selection since the metal film shows wide reflectance spectrum. A TTD for 10 GHz linear PAAs capable of steering beams in three different directions at 0$^{\circ}$and $\pm$30$^{\circ}$has been built. Experimental results on time delays are in good agreement with those calculated at all the steering angles. A 10 GHz linear array antenna with eight antenna elements red from the proposed TTD has been designed and the far-field radiation pattern or this antenna has been obtained by simulation.

• Journal of the Institute of Electronics and Information Engineers
• /
• v.51 no.10
• /
• pp.21-25
• /
• 2014

Scan capabilities of Fabry-Perot cavity (FPC) antennas are investigated for the case of a $4{\times}1$ thinned array placed inside the cavity. The FPC array antenna has higher maximum gain and lower sidelobe level (SLL), but the maximum scan angle of the thinned array is 14-17% lower than the patch array alone, due to increased mutual coupling in the FPC structures. However, unlike the bare thinned array, the SLL of FPC array does not suffer from the grating lobe problem even though it has a relative large element spacing of more than $1.0{\lambda}_0$.

• Korean Journal of Optics and Photonics
• /
• v.15 no.6
• /
• pp.591-596
• /
• 2004

In this paper, a photonic RF true-time delay based on a partially side-polished fiber Bragg grating with heating electrode has been proposed and fabricated. It features continuous voltage-controlled operation, requiring no mechanical perturbation and no moving parts. For an RF signal carried over an optical signal, the time delay has been obtained by controlling the voltage applied to the electrode and thus adjusting its reflection positions from the fiber grating via the thermooptic effect. The achieved time delay is about 100 ps with the electrical power consumption of 280 mW.

• Journal of the Korean Institute of Telematics and Electronics D
• /
• v.36D no.4
• /
• pp.25-33
• /
• 1999

Leaky wave radiation and surface wave launching problems in a dielectrically covered and periodically slitted parallel-plate waveguide(PPW) are considered for the TEM wave incidence case. Both the infinite and finite periodic geometries are analyzed by use of the method of moments. Some numerical results for the reflected and transmitted powers in the PPW, radiation efficiency into the free space, surface wave launching efficiency into the slab, antenna gain, and radiation patterns against dielectric thickness are presented to show the effect of the dielectric cover on the performances of the slitted leaky wave antenna. In addition, the method for improving surface wave launching efficiency using the proposed periodic geometry is described and maximum launching efficiency of 97.5% is obtained theoretically. So this structure is thought to be promising as an efficient feeder of dielectric grating antenna as well as image guide.

• The Journal of the Institute of Internet, Broadcasting and Communication
• /
• v.19 no.3
• /
• pp.141-147
• /
• 2019

In this paper, a beam pattern performance analysis was performed according to number of array elements and spacing of the phase array antenna. The distance between array elements in an array structure design was reduced due to the electrical length of Ka-band, which increases the number of array elements in applying the aperture. If the number of elements reduce by widening the array distance, the grating lobes of the same size as the main beam will occur in visible region. If the number of array elements should be applied to a system where the number of array elements should be minimized, the analysis was performed on a plan to reduce the number of array elements and minimize degradation of performance, such as beam width and side lobe level.

• Journal of the Korean Institute of Telematics and Electronics D
• /
• v.35D no.12
• /
• pp.12-20
• /
• 1998

The non-uniform leaky wave structure of the slits in a parallel-plate waveguide is analyzed from the viewpoints of transmitting(receiving) leaky wave antenna and grating coupler. Period and slit width are simultaneously varied along the leaky wave structure to construct the leaky wave structure with a specific distribution of complex propagation constant. Some results for the equivalent magnetic current distributions over the slits and the radiation characteristics of the leaky wave structure with various source(equivalent magnetic current) distributions such as Gaussian, uniform, cosine, cosine-squared, and Taylor distributions are given and compared with each other.

• Korean Journal of Optics and Photonics
• /
• v.17 no.1
• /
• pp.7-17
• /
• 2006

In this paper, we proposed an optical true time-delay (TTD) for planar phased array antennas (PAAs), which is composed of a wavelength-dependent optical true time delay (WDOTTD) followed by a wavelength-independent optical true time delay (WIOTTD). The WDOTTD is a fiber Bragg gratings (FBGs) Prism and the WDOTTD is a fiber delay-lines matrix of which each component consists of a certain length of fiber connected to cross-ports of a 2${\times}$2 MEMS switch. A 10-GHz 2-bit${\times}$4-bit two-dimensional optical TTD has been fabricated by cascading a WDOTTD with a maximum time delay of 810 ps to a WIOTTD of $\pm$50 ps. Time delay and insertion loss for each radiation angle have been measured. Time delay error for the WIOTTD has been measured to be less than $\pm$1 ps. We have also designed a two-dimensional 10-GHz PAA composed of 8${\times}$8 microstrip patch antenna elements driven by the proposed TTD. The radiation patterns of this PAA have been obtained by simulation and analyzed.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.29 no.8
• /
• pp.599-607
• /
• 2018

This paper presents a ground-to-air bistatic radar system and its implementation algorithm, which resembles an SAR(synthetic aperture radar) reconstruction algorithm. Via cooperative working between a standoff transmitting radar and an array of ground based receiving radars, it detects and images moving targets under clutter in the air. In the proposed system, the whole receiving antenna aperture is synthesized by physical ground based radars, and thus, unlike conventional SAR, it does not require long illumination time of the target area. The reconstruction algorithm uses planewave approximation based polar format processing, which alleviates the requirement of positioning the receiving radars, which can cause grating lobes if not chosen properly. We derive a reconstruction algorithm including clutter suppression and discuss implementation issues, such as the resolution of a reconstructed image and the method of compensation for the irregularity of the receiving radars' positions. A simulation that validates the proposed algorithm is also shown.